Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

An improved Gaussian approximation for probability of bit-erroranalysis of asynchronous bandlimited DS-CDMA systems with BPSK spreading

This paper analyzes probability of bit-error (P_e) performance of asynchronous bandlimited direct-sequence code-division multiple-access systems with binary phase-shift keying spreading. The two present methods of P_e analysis under bandwidth-efficient pulse shaping: the often-cited standard Gaussian approximation and the characteristic function (CF) method suffer from either a low accuracy in regions of low P_e (< 10^-3) or a prohibitively large computational complexity. The paper presents an alternate method of P_e analysis with moderate computational complexity and high accuracy based on a key observation. A sequence of chip decision statistics (whose sum yields a bit statistic) forms a stationary, m-dependent sequence when conditioned on the chip delay and phase offset of each interfering signal. This observation permits the generalization of the improved Gaussian approximation previously derived for the rectangular pulse and the derivation of a numerically efficient approximation based on the CF method. Numerical examples of systems using the square-root raised-cosine and IS-95 pulses illustrate THE P _e performance, user capacity and the accuracy of the proposed method     

The onset of vortex instability in laminar forced convection flow through a horizontal porous channel

The onset of convective instability in a fluid-saturated porous layer between the two horizontal plates heated isothermally from below has been analyzed theoretically by using propagation theory. In the analysis the thermal dispersion coefficient is assumed to be proportional to the streamwise velocity. The results show that both inertia and thermal dispersion stabilize the system.     

Synthesis and characterization of an interpenetrating polymer network composed of poly(methacrylic acid) and poly(vinyl alcohol)

Temperature and pH‐responsive interpenetrating polymer network (IPN) hydrogels, constructed with poly(methacrylic acid) (PMAA) and poly(vinyl alcohol) (PVA), by a sequential IPN method, were studied. The characterization of IPN hydrogels was investigated by Fourier‐transform infrared spectroscopy, differential scanning calorimetry (DSC) and swelling under various conditions. The IPN hydrogels exhibited relatively high swelling ratios, in the range 230–380 %, at 25 °C. The swelling ratios of the PMAA/PVA IPN hydrogels were pH and temperature dependent. DSC was used for the quantitative determination of the amounts of freezing and non‐freezing water. The amount of free water increased with increasing PMAA content in the IPN hydrogels. Copyright © 2004 Society of Chemical Industry     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.     

Study on the c-axis preferred orientation of ZnO film on various metal electrodes

ZnO thin film was deposited on various metal electrodes by reactive sputtering, and c-axis preferred orientation of the film has been studied. ZnO, which has high piezoelectricity, is promising for oscillators or filter devices such as surface acoustic wave (SAW) device, gas sensor, and film bulk acoustic resonator (FBAR). But, for the application of ZnO film for these devices, the film should be grown with c-axis normal to the electrode. In this study, Pt, Al, and Au were deposited on Si wafer, and the surface roughness and crystal structure of the ZnO film on the electrode were investigated using AFM, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Columnar structures of ZnO films were grown with c-axis normal to all electrodes, and among them Pt electrode showed the highest preferred orientation of ZnO film.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.