Fast removal of Pb(II) and Cu(II) from contaminated water by groundwater treatment waste: impact of sorbent composition

ABSTRACT

A non-hazardous groundwater treatment waste (GWTW) was examined as a low-cost sorbent for Pb(II) and Cu(II) ions. The content of the dominant elements in GWTW was as follows: 78% Fe₂O₃, 7.4% P₂O₅, 7.4% CaO and 5.2% SiO₂. The removal of Pb(II) and Cu(II) was fast, and more than 67–95% of ions were accumulated by GWTW during the first 3 min. The sorption capacity of GWTW depends on solution pH, concentration and temperature. Equilibrium data fitted well with Langmuir–Freundlich and Langmuir-partition models. The inherently formed nano-adsorbent could be utilized for the treatment of water contaminated with Pb(II) and Cu(II) ions.     

MIG Brazing of Galvanized Thin Sheet Joints for Automotive Industry

MIG welding of zinc-coated thin plates in the automotive industry leads to major issues, mainly zinc evaporation followed by a decrease of corrosion resistance, as well as residual strains and stresses difficult to minimize. The use of a lower heat input technique for joining galvanized steels would bring significant benefit, if the final overall mechanical properties of the joints are adequate for the application. The use of MIG brazing (MIGB) with the recently commercialized alloyed copper-based filler metal is an alternative worth considering. The present paper addresses the MIGB processes, describing the influence of the different shielding gases and the process parameters on the mechanical, corrosion, and metallurgical properties of the joint, when lower heat input procedures are targeted. The paper describes the influence of the gases on the mechanical properties of the brazed joint, both in normal conditions after joining and after corrosion in a salt water environment. Microstructural features of the different zones are discussed. Results of corrosion and tensile tests are presented and interpreted.     

Solution properties of triphenylsilyl cellulose

Five samples of triphenylsilyl cellulose (TPSC) are characterized in solution by osmometry, viscometry, and size exclusion chromatography. The isolated and purified cellulose ethers are prepared in a N,N‐dimethylformamide and pyridine medium under heterogeneous starting conditions and a nitrogen atmosphere by silylation of activated celluloses with triphenylchlorosilane at 115–120°C. TPSCs are characterized by their polydispersities and degrees of substitution by osmometry and viscometry in various solvents. The Mark–Houwink–Sakurada equation coefficients are evaluated in 1,1,1‐trichloroethane, chloroform, and o‐xylene at 30°C and in o‐xylene over a temperature range of 30–70°C. Values of 2.12–2.18 are obtained for exponent a. This indicates, in combination with low values of the preexponential factor (on the order of 10^?12), strong stiffness of the macromolecular chains. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1257–1261, 2007     

Processing Ti-25Ta-5Zr Bioalloy via Anodic Oxidation Procedure at High Voltage

The current paper reports the processing of Ti-25Ta-5Zr bioalloy via anodic oxidation in NH4BF4 solution under constant potentiostatic conditions at high voltage to obtain more suitable properties for biomedical application. The maximum efficiency of the procedure is reached at highest applied voltage, when the corrosion rate in Hank’s solution is decreased approxomately six times. The topography of the anodic layer has been studied using atomic force microscopy (AFM), and the results indicated that the anodic oxidation process increases the surface roughness. The AFM images indicated a different porosity for the anodized surfaces as well. After anodizing, the hydrophilic character of Ti-25Ta-5Zr samples has increased. A good correlation between corrosion rate obtained from potentiodynamic curves and corrosion rate from ions release analysis was obtained.     

KINETICS OF THE SIMULTANEOUS SORPTION OF NONIONIC SURFACTANT AND COPPER(II) BY POLY ACRYLIC ACID - FUNCTIONALIZED ION EXCHANGER

ABSTRACT

Kinetics of the simultaneous sorption of nonionic surfactant oxyethylated alcohols (OS-20) and copper(II) by hydrogen containing form of Purolite C 106 polyacrylic acid-functionalized cation exchanger was investigated: kinetic curves measured, effective coefficients of intraparticle diffusion (D), effective kinetic coefficients of the external mass transfer ((β) were calculated. The sorption of copper (II) and OS-20 is controlled by the intraparticle diffusion. The diffusion rate depends on the solution acidity: on increasing the acidity both the rate of copper (II) intraparticle diffusion and the equilibrium sorption decrease while the rate of intraparticle diffusion and the equilibrium sorption of OS-20 increase. The presence of copper (II) results in an increase in OS-20 diffusion rate but leads to a decrease in the equilibrium sorption of OS-20. The action of OS-20 results in the decrease in the equilibrium sorption of copper (II).The simultaneous sorption of oxyethylated alcohols and copper (II) by Purolite C 106 can be applicable for the purification of sewage including copper plating rinsewater A column filled with Purolite C 106 would not limit the productivity if integrated into the system of sewage purification by ion exchange |The simultaneous sorption of OS-20 and copper (II) by Purolite C 106 ion exchanger can be applicable for the purification of sewage including copper plating rinsewater. With respect to the coefficients of intraparticle diffusion for both copper (II) and OS-20 the column filled with Purolite C 106 would not limit the productivity if integrated into the system of sewage purification using ion exchange,     

Alkali-activated blends of calcined AlF3 production waste and clay

Recently, alkali-activated materials have shown great potential for use in the construction industry. The aim of this research was to study the properties of alkali-activated clay and the effect of incorporating AlF₃ production waste from a fertilizer production plant. The AlF₃ production waste, which was rich in alumina and silica, contributed to improved mechanical behaviour for all the mixtures investigated. This demonstrated the potential for use of this waste material. It was also noted that the dosage of Na₂O, Al₂O₃, and SiO₂ are significant factors that influence the binding mechanism and properties of alkali-activated clay samples. The raw materials, precursors, and alkali-activated samples were investigated by X-ray diffraction, fluorescence spectroscopy, and scanning electron microscopy. The highest compressive strength (17.50?MPa) was observed for alkali-activated clay samples containing 25% AlF₃ production waste, with an increase in compressive strength of up to 64% compared to the samples without the AlF₃ production waste. Deleterious natrite was shown to form in the samples without the production waste, which could be the reason for the lower observed mechanical properties of such samples.     

Combinatorial Strategy for Studying Biochemical Pathways in Double Emulsion Templated Cell-Sized Compartments

Cells rely upon producing enzymes at precise rates and stoichiometry for maximizing functionalities. The reasons for this optimal control are unknown, primarily because of the interconnectivity of the enzymatic cascade effects within multi-step pathways. Here, an elegant strategy for studying such behavior, by controlling segregation/combination of enzymes/metabolites in synthetic cell-sized compartments, while preserving vital cellular elements is presented. Therefore, compartments shaped into polymer GUVs are developed, producing via high-precision double-emulsion microfluidics that enable: i) tight control over the absolute and relative enzymatic contents inside the GUVs, reaching nearly 100% encapsulation and co-encapsulation efficiencies, and ii) functional reconstitution of biopores and membrane proteins in the GUVs polymeric membrane, thus supporting in situ reactions. GUVs equipped with biopores/membrane proteins and loaded with one or more enzymes are arranged in a variety of combinations that allow the study of a three-step cascade in multiple topologies. Due to the spatiotemporal control provided, optimum conditions for decreasing the accumulation of inhibitors are unveiled, and benefited from reactive intermediates to maximize the overall cascade efficiency in compartments. The non-system-specific feature of the novel strategy makes this system an ideal candidate for the development of new synthetic routes as well as for screening natural and more complex pathways.     

Earth Observation application development based on the Grid oriented ESIP satellite image processing platform

Satellite images supply important information on earth surface, weather, clime, geographic areas, vegetation, and natural phenomena. Processing of satellite data requires high computation resources and flexible tools in order to search, discover, and reveal the main information, to experiment new algorithms, and to include them into new Earth Observation applications. This paper describes the features and the architectures of the ESIP and gProcess platforms, supporting the Grid based satellite imagery processing. The development methodology of Earth Observation applications is highlighted as well in order to hide the Grid complexity to the user.     

The rheological and structural behavior of silylcellulosics derivatives

The trimethylsilylcellulose (TMSC) samples were characterized in solution by osmometry, viscometry, and gel permeation chromatography. The Mark-Houwink-Sakurada (M-H-S) equation coefficients were determined in chloroform, 1,1,1-trichloroethane, and o-xylene, in all cases the exponent “a” being higher than unit, this indicating a great stiffness of the macromolecules in solution. Also, the temperature dependence of the limiting viscosity number and M-H-S coefficients respectively for TMSC in o-xylene were studied. The exponent from M-H-S equation is also higher than unit, and increases linearly with the temperature. The GPC studies indicates a relative high polydispersity of the studied samples; the polydispersity index being situated between 2 and 3. The change of the crystalline structure as the result of silylation reaction was evidenced, the crystallinity of silyl derivatives depending on the substitution degree (DS), and the molecular weight. The viscous flow parameters for dilute solutions of trimethylsilylcellulose in o-xylene were determined in the temperature range 30–70°C. The temperature dependence of the dynamic viscosity of the solutions obeys an Arrhenius-type equation in which the apparent activation energy is linearly dependent on both the solution's concentration and molecular weight. For preexponential factor no significant dependence on concentration and molecular weight was found. This behavior was attributed to the very great stiffness of the macromolecular chains. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2277–2285, 2001