Response of dairy cows to high doses of a sustained-release bovine somatotropin administered during two lactations. 2. Health and reproduction.

Eighty-two lactating Holstein cows in their first, second, or third lactation received either one, three, or five concurrent i.m. injections of a unit dose (.6 g) of zinc methionyl bST (sometribove) or five doses of the vehicle. Injections were given at 14-d intervals from 60 +/- 3 d postpartum until the end of lactation or necropsy. Thirty-eight animals were continued on treatment for a 2nd yr. Sometribove did not affect the incidence of ketosis, milk fever, tetany, or pneumonia. Digestive disorders, primarily cows going off feed, were increased by bST during yr 1 only. The incidence of lameness was increased by bST in some time frames because of an increase in the 3.0-g bST group. Lameness was not associated with treatment-specific histopathologic changes or with abnormalities in cartilage or bone. Reproductive health generally was unaffected by treatment, but delayed conception and increased incidence of abortion were noted. Incidence of cystic ovaries was unaffected by bST. Pregnancy rates were decreased during the 100-d breeding interval of yr 1 but not during the 215-d interval of yr 2. The incidence of clinical mastitis was increased by bST, primarily at the 3.0-g dose. During the 2-yr study, 0, 3, 3, and 2 cows died or became moribund on 0, .6, 1.8, and 3.0 g of bST, respectively. Health issues identified for further evaluation included lameness and clinical mastitis for the 3.0-g group and early removal from the herd and decreased reproductive performance for all bST groups. Bovine somatotropin caused no treatment-specific toxic effects in dairy cows even at 3.0 g every 14 d.     

Studies of space-averaged mass transport in the FM01-LC laboratory electrolyser

Measurements of the mass transport limited current for the reduction of ferricyanide in 1M m potassium hydroxide and of copper(II) in 1.5 m sulphuric acid as a function of electrolyte flow rate are used to characterize the space-averaged mass transport properties of the FM01 laboratory electrolyser, with and without six types of polymer mesh turbulence promoters. In the absence of a promoter, the results followed the equation For the cell with the preferred turbulence promoter, the corresponding equation is Pressure drop data are also reported and it is confirmed that the presence of a turbulence promoter need not lead to a significant increase in the pressure drop over the reactor.     

The effect of solution variables on the solution of cellulose in dimethyl sulfoxide

Through the study of the effects of concentration, temperature, and molar ration (of paraformaldehyde to cellulose) on solution viscosity and per cent transmittance (at 530 nm), it has been demonstrated that cellulose solutions in dimethyl sulfoxide (DMSO) are readily produced. By heating 1, 2, and 50 to 100 parts by weight of cellulose, paraformaldehyde, and DMSO, respectively, extremely viscose cellulose solutions and gels were prepared. Solutions with concentrations as high as 10% were prepared. However, the optimum conditions to effect complete cellulose solution in DMSO at 75°C were found to be 0.5% cellulose and 0.8 and 1.0% paraformaldehyde. This corresponds to a paraformaldehyde-to-cellulose molar ratio of about 10:1.     

Chromium distribution between liquid iron and molten basic slags

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-SiO₂-FeO-Cr₂O₃ type in the temperature range 1526° to 1734°C The effects of slag oxidation, temperature, and basicity were observed.     

An investigation of multiphase CFD modelling of a lateral sloshing tank

A near-resonant, sway-induced sloshing flow in a rectangular tank is used to compare a homogeneous and inhomogeneous multiphase approach for fluid density and viscosity in a commercial CFD code. Dimensional analysis of the relative motion between the phases suggests the application of an inhomogeneous multiphase model whereas previous published work has used the computationally cheaper homogeneous (or average property) approach. The comparison between the computational and experimental results shows that the homogeneous model tends to underestimate the experimental peak pressures by up to 50%. The inhomogeneous multiphase model gives good agreement with the experimental pressure data. Examination of the relative velocity at the fluid interface confirms that the inhomogeneous model is the appropriate model to use for the simulation of a violent sloshing flow.     

Preferred Orientations in Iodide Titanium

The wire textures for cold rolled and recrystallized iodide titanium and the sheet textures for this material produced by cold and hot rolling, and recrystallization at a series of temperatures were determined. The effect of the α → β transformation on the sheet texture was noted.     

An investigation of the performance portability of OpenCL

This paper reports on the development of an MPI/OpenCL implementation of LU, an application-level benchmark from the NAS Parallel Benchmark Suite. An account of the design decisions addressed during the development of this code is presented, demonstrating the importance of memory arrangement and work-item/work-group distribution strategies when applications are deployed on different device types. The resulting platform-agnostic, single source application is benchmarked on a number of different architectures, and is shown to be 1.3–1.5× slower than native FORTRAN 77 or CUDA implementations on a single node and 1.3–3.1× slower on multiple nodes. We also explore the potential performance gains of OpenCL’s device fissioning capability, demonstrating up to a 3× speed-up over our original OpenCL implementation.     

多内核、多线程的SoC引致调试困难

有经验的开发人员都知道,要保证嵌入式产品的成功实现、调试和维护,好的工具支持是非常关键的.SoC(系统芯片)设计带来了一系列新的问题,使好的工具支持变得更加关键.部分问题可以归因于SoC设计使用的部件,其可访问性和可视性本来就有所下降;其它原因则可归因于在硬件和软件方面复杂性的增加.