Carbon Bonding State Has a Small Effect on Melting of Direct-Reduced Iron

Metallurgical and Materials Transactions B - The concentration and chemical bonding state of carbon in direct-reduced iron (DRI) might affect DRI melting temperature and rate. The effects of carbon...     

Effect of heat treatment in air on the thermal properties of SiC fibre reinforced composite: Part 2 A magnesium aluminium silicate (MAS) matrix glass ceramic composite

The thermal properties of a magnesium aluminium silicate (MAS) glass ceramic matrix composite reinforced by SiC (Nicalon) fibres have been investigated before and after heat treatment in the temperature range 600–1,200 °C. Within this temperature range, during the heat treatment at lower temperatures such as 600 and 700 °C, the oxidation of the carbon layer occurred and mixture of silicon and carbon was formed in the interface. This results in a decrease in thermal diffusivity values. After heat treatment at the temperatures higher than 1,000 °C, the carbon layer was thickened and resulted in the higher thermal diffusivity values.     

Fast Decodable Turbo Codes

Decoding delay is an important consideration for the use of turbo codes in practical applications. We propose a new structure for turbo codes which is very suitable for parallel decoding. It is shown by union bound analysis and simulation results that the proposed system performance is comparable to that of the classical turbo codes     

Significance of fluid regime in biological filtration

A dispersed flow model previously developed to study substrate utilization in unsaturated media was experimentally verified and its practical application was considered. For this purpose, measurements were made using tap water and a synthetic feed solution. The importance of the change in fluid regime as regards to the simultaneous transport and reaction within biological filters were demonstrated. The effect of drop formation and the breakage of liquid jets inside the filters on substrate utilization was also shown.     

硅灰混凝土的研究及其在公路道面的应用

 了提高道路路面混凝土的抗磨能力，采用硅灰代替部分水泥的方法，对硅灰混凝土的性能进行了较系统的试验研究。成果表明其抗压强度、抗弯强度、抗磨强度等指标都得到明显提高，全面达到和超过了规范要求。并已在丹江口水利枢纽上坝公路中得到应用，实践证明硅灰混凝土技术可靠、经济合理、易于施工。特别是抗磨度的提高，对延长公路路面的使用寿命具有重要意义。     

High-quality photonic sampling streams from a semiconductor diodering laser

We report on the development of an ultralow-noise, external-cavity, actively mode-locked semiconductor diode laser for application in next-generation photonic sampling systems. A summary of harmonically mode-locked noise characteristics in a 65-MHz ring cavity is presented through the range of pulse repetition frequencies between 130 MHz and 8.3 GHz (2nd-128th harmonic). Important implications regarding the use of gain-versus-loss modulation as the active modelocking mechanisms are discussed. We also report what are, to our knowledge, the lowest noise characteristics achieved to date for a semiconductor diode laser operating at 10 GHz. Individually optimized results of 0.12% rms amplitude noise (10 Hz-10 MHz), and 43 fs rms residual phase jitter (10 Hz-10 MHz) provide a theoretical resolution of 8.6 bits in a 10-GSPS optical analog-to-digital converter. We have also achieved dispersion-compensated pulsewidths; as short as 1.2 ps, and shown successful operation of a novel phase-locked-loop capable of reducing the rms; residual phase noise by as much as 91% within its response bandwidth. Finally, the first measurements of residual phase noise out to the Nyquist frequency (5 GHz) are presented, providing an upper bound on the rms residual phase jitter of 121 fs (10 Hz-5 GHz)     

A STUDY OF THE FLOTATION OF OXIDIZED AHASRA COAL

The flotation of oxidized Amasra Coal which was collected between 1973-1978 and, stored in the atmospheric conditions was examined In this work. Coal samples were fractioned by wet screening to +0.560 mm, -0.500 + 0.140 mm, -0.140 mm particle sizes and first fraction was ground to -0.560 mm before flotation. Motorin and pine oil which had been heated at 125° C for 5 hours were used ns flotation reagents. The influence of impeller speed, aeration rate, solid concent of the pulp, reagent amounts were examined and optimum values were determined. Increase of the pine oil amount added to the pulp, increased the coal. recovery on the flotation of this oxidized coal.