A video DSP with a macroblock-level-pipeline and a SIMD typevector-pipeline architecture for MPEG2 CODEC

A video DSP with macroblock-level-pipeline and a SIMD type vector-pipeline architecture (VDSP2) has been developed, using 0.5 μm triple-layer-metal CMOS technology. This 17.00 mm×15.00 mm chip consists of 2.5 M transistors, and operates at 100 MHz. The real-time encoder and decoder specified in the MPEG2 main profile at the main level can be realized with two VDSP2's and a motion estimation (ME) unit, and one VDSP2 respectively, at an 80 MHz clock rate, with a total power dissipation of 4.2 W at 3.3 V     

Thermodynamic study of the phase equilibria in the Sn−Ti−Zn ternary system

The Sn−Ti−Zn ternary phase diagram has been constructed using the CALPHAD technique. The Ti−Zn binary system phase boundaries were determined using differential scanning calorimetry and the solid-liquid diffusion couples method. In addition, the formation energy of some stoichiometric compounds was obtained using first-principle band energy calculations. For the ternary system, some alloys were prepared by equilibration at 600 or 700 °C, and the compositions of the precipitates were analyzed using electron probe microanalysis. Thermodynamic assessment of the Ti−Zn and Sn−Ti−Zn systems was performed based on the experimental information and by adopting reported values of the thermodynamic properties of the Sn−Zn and Sn−Ti binary systems. Microstructural observation showed that Sn₃Ti₅Zn₁₂ exists in the ternary system. Seven types of invariant reaction on the Sn-rich liquidus surface of the ternary system are predicted by the phase diagram calculations. The ternary eutectic point falls at 0,0009 mass% Ti and 8.69 mass% Zn, at T=192.40°C, which is slightly lower than the calculated eutectic point of Sn−Zn binary alloy (T=192.41°C). Based on these results, a nonequilibrium solidification process using the Scheil model was simulated. This paper was presented at the International Symposium on User Aspects of Phase Diagrams, Materials Solutions Conference and Exposition, Columbus, Ohio, 18–20 October, 2004.     

Local disturbances preceding a running crack front in a viscoelastic solid

The local disturbances ahead of a running crack front in a viscoelastic solid were measured through noncontact electro-optical tools. It was observed that the very high local strain rate up to 200/sec exists even in the present quasistatic loading case. It may be concluded that the running crack propagation velocities, not the conventional average strain rates ranging from about 10^?4/sec to 10^?2/sec, govern the local disturbances, as the crack propagation velocities always exceed 200m/sec for both average strain rates, while the local strain rates observed do not show much differences between both average strain rate cases.     

A manufacturing XML schema definition and its application to a data management system on the shop floor

Digitization for sharing knowledge on the shop floor in the machinery industry has been given much attention recently. To help engineers use digitization practically and efficiently, this paper proposes a method based on manufacturing case data that has a direct relation to manufacturing operations. The data are represented in XML schema, as it can be easily applied to Web-based systems on the shop floor. The definitions were made for eight manufacturing methods including machining and welding. The derived definitions consist of four divisions of metadata, work-piece, process and evaluation. Three divisions except for the “process” division are common to the manufacturing methods. The average number of elements for a manufacturing method is about 200. The represented schema is also used to convey knowledge such as operation standards and manufacturing troubleshooting on the shop floor. Using the definitions, a data management system is developed. It is a Web-based Q&A system, in which the engineers specify the manufacturing case data mainly by selecting from the candidates. Then, the system fills in the blank portions and/or shows messages to help complete the case data. The proposed method is evaluated through practical scenarios of arc welding and machining.     

A study of hypervelocity impact on cryogenic materials

This paper reports a result of hypervelocity impact experiments on cryogenically cooled aluminum alloys and a composite material. Experiments are carried out on a target palate at 122 K. Aluminum spheres at 1.95 km/s in 50 kPa air were impinged against the target plate at cryogenic temperature and the result was compared with room temperature target plates. Hypervelocity impact (HVI) processes were visualized with shadowgraph arrangement and recorded with high-speed video camera and to ensure the temperature dependence we compared HVI tests with metal target plates with AUTODYN 2D and SPH numerical simulations. We found that cryogenic impacts created slight differences of impact damage from room temperature ones, i.e., the shape and averaged diameters of HVI crater holes were less at cryogenic impacts.     

Pyrolysis Products of Lignin in Open and Sealed Vessels Studied by Py-GC-MS

The pyrolysis products of lignin in open and sealed vessels were studied by pyrolysis—gas chromatography—mass spectrometry (Py-GC-MS). Several kinds of phenolic derivatives were observed in the pyrolysates in both treatments, while phenolic compounds with alkenyl or acetyl groups had higher relative contents in the open vessel than those in the sealed vessel. Phenol and its alkyl or mono-methoxy substituted derivatives become the main pyrolysis products in the sealed vessel. Most of the lignin pyrolysis products in the open vessel could be detected by Py-GC-MS, but some active products would go through further reaction in the sealed vessel.     

Guiding and blocking of highly charged ions through a single glass capillary

Highly charged ions produced in an electron beam ion trap, I^q+, q = 10-50, were transmitted through a tapered glass capillary having diameter of at the end. We found that for a particular beam current, there exists an optimum tilting angle of the capillary in which a steady output of ions is observed, while for smaller angles, the ion counts first rise, then gradually decay on a time scale of minutes. In the case of steady transmission, the charge state distribution is found to be slightly towards the lower side.     

Observations of xenon gas-treated barley cells in solution by atomic force microscopy

Barley cells cut from a sprout were exposed to either air or high-pressure xenon gas for 3 days and the surface of those cells was observed by atomic force microscopy (AFM) to examine the effect of the gas treatment. This method enabled the direct observation of the fresh surface of the barley cells in solution at high resolution. The cuticle layer was preserved on the primary cell wall of 0.48 MPa xenon gas-treated barley cells, while air-treated barley cells lost the cuticle layer from the primary cell wall. These findings indicate that the high-pressure xenon gas treatment is effective to preserve the cuticle layer attached to the primary cell wall. AFM is a powerful tool for the observation of the surface structure of living plant cells in solution.     

Characterization of natural resin shellac by reactive pyrolysis-gas chromatography in the presence of organic alkali

A method to determine chemical composition of natural resin shellac was developed on the basis of reactive pyrolysis-gas chromatography (Py-GC) in the presence of an organic alkali, tetramethylammonium hydroxide ((CH(3))(4)NOH, TMAH). Py-GC using 25% TMAH aqueous solution enabled the highly sensitive determination of terpenic acids, aleuritic acid, several minor fatty acids, and the wax components of shellac as their methyl derivatives on the resulting pyrograms with less than 2.0% relative standard deviations without using any cumbersome pretreatment. The observed average distributions of each resin acid component determined by reactive Py-GC for shellac samples from India and Thailand showed that the average ratios among terpenic acids, aleuritic acid, and the other fatty acids were about 53:34:14 for Indian shellac and 51:35:14 for Thailand shellac, respectively, suggesting a slightly significant difference. However, clearer discrimination of the shellac samples from the two different growing places was attainable by applying principal component analysis for the mole percent distributions of all the acidic components determined by reactive Py-GC.     

The Chemistry of PCR Primers: Concept and Application

DNA is a typical organic compound with marked differences from other chemicals and biopolymers because DNA can be amplified by the enzyme polymerase. DNA can be, in principle, amplified from a single copy by the polymerase chain reaction (PCR). In this review, we focus our attention on the chemistry of PCR primers. Because PCR is basic technology in biology research fields, we sometimes use chemically labeled primers without any awareness of the chemistry they leave behind. We would like to emphasize that chemically labeled primers contain a lot of potential for different chemistry ideas and much study is still necessary to advance PCR for single-nucleotide polymorphism (SNP) typing, genetic diagnosis, and other fields. Two categories of primers, affinity-capture primers and signaling primers, are discussed from the viewpoints of their chemical concepts and applications. Affinity-capture primers are used for purification, isolation, and manipulation of PCR products by high specificity and affinity to the cognate molecules by molecule molecule interactions, whereas signaling primers report the hybridization and/or progress of PCR amplification by a signal change, in most cases by a fluorescence change. The content of this review may be useful for a better understanding of the chemistry of PCR primers and, more importantly, for the invention of novel PCR chemistry.