Decreasing the number of test specimens by utilizing both fracture stress and fracture location for the estimation of Weibull parameter

In a bending load test for brittle materials, such as ceramics for spacecraft and aircraft, decreasing the number of test specimens required is a crucial problem. This paper discusses the effectiveness of using the information of both fracture stress and fracture location to decrease the number of specimens required to obtain the same precision as the Weibull estimator. The following results were obtained: It was found that by adding the fracture location information, the precision of the Weibull parameter estimation under the optimal design became 1.5–1.9 times better compared with the case of using only the fracture stresses. This means the number of samples necessary to attain the same precision becomes 1/1.5–1/1.9. Tables and figures which give information on the number of samples necessary to attain the required precision are given.     

Volumetric properties of mixtures of 1,4-dioxane and water at high pressures

Densities of aqueous of 1,4-dioxane have been measured at temperatures from 298 to 348 K and at pressures up to 40 MPa by a vibrating-tube method. Molar volumes obtained with an estimated uncertainty of ±0.2°,% are correlated with pressure by the Tait equation within the experimental uncertainty. Pressure and composition dependences of the excess molar volume, partial molar volume, and isothermal compressibility are determined and they are compared with those of other aqueous solutions.     

Preparation of pyrochlores. A1−xHxTaO3·nH2O (A=Na,K)

Pyrochlores of A_1?xH_xTaO₃·nH₂O (A=Na,K) were prepared under the hydrothermal conditions. The values of x for these compounds were increased from 0.3 to 0.5 for A=Na and from 0.2 to 0.5 for A=K by treatment with the distilled water. The compounds with x<0.5 were decomposed to a mixture of NaTaO₃ and Na₂Ta₄O₁₁ for A=Na, or to a mixture of KTaO₃ and a tetragonal tungsten bronze phase, and those with x=0.5 to a single phase of A₂Ta₄O₁₁ at elevated temperatures. Below the decomposition temperatures, defect pyrochlores with oxygen vacancies, $\text{A}{}_{\mathrm{<mtext>1?</mtext><mtext>x</mtext>}}\text{TaO}{}_{\mathrm{<mtext>3?</mtext><mtext>x</mtext><mtext>2</mtext>}}$, were produced. They were hygroscopic, and in the case of A=K and x=0.5 the original phase was recovered by leaving in air for several hours.     

Study on axiomatic rules for building up relationships between requirement and source programs

The purpose of our study is to build up relationships between requirement and source programs with our originally thought-out rules. When other rules to be derived from these original rules are applied to software development, even a single instruction in a programming language could be determined, and the program would satisfy the requirement. More specifically speaking, these rules will turn into a formula or a prototype of software programs. Hence, when the variables in the requirement are placed in the formula, we can get a required program in an automatic way.     

Is it possible to differentiate between choledochal cyst and congenital biliary atresia (type I cyst) by antenatal ultrasonography?

Both choledochal cyst and congenital biliary atresia (type I cyst) may share the same ultrasonographic pattern. We report 2 cases which were shown to have cystic structures on the upper abdomen by antenatal ultrasonography. The size of the choledochal cyst found at 24 weeks' gestation increased steadily as gestational age advanced. But the size of the cyst in congenital biliary atresia found at 29 weeks' gestation remained unchanged throughout the remaining pregnancy. Cyst enlargement, therefore, may suggest the possibility of a choledochal cyst.     

Forming mental models in learning operating procedures for terminalequipment

People faced with an unfamiliar product or service tend to fall back on mental models based on analogical relationships with familiar products or services. Two experiments on the analogical relationships or metaphors that people might use when operating a communications terminal are described. In the first experiment, the role previously acquired operating knowledge has in determining the mental models people use when directory dialing with novel equipment is examined. In a second experiment, it is shown that an explicit appeal to an analogy between conventional mail and electronic mail can help users learn to use an electronic mail system, and make it easier for them to remember how to use the system as long as 90 days after initial exposure. It is concluded that the mental model is constructed only from the user's operating knowledge acquired as a result of past experiences, and the metaphor method is effective when the instructions are metaphorically taught     

Robust stabilization of a magnetic suspension system using H∞ Control Theory

This paper presents the robust control design of a magnetic suspension system for a flexible beam which is a simplified model of an elastic rotor in a magnetic bearing system. To stabilize this magnetic suspension system which is unstable in nature, the H^infin; control theory is applied for a design of the control system. To apply the H^infin; control theory, a statespace model of an augmented plant with frequency-weighting functions is constructed. This augmented plant has two inputs which are the exogenous inputs and the control inputs, and two outputs which are the sensor outputs and the regulated outputs. Here we consider the mixed sensitivity problem. The H^infin; controller is implemented by a digital controller which is able to execute the computations very quickly. For the evaluation of the control performance, several experiments are made. The robustness of the closed-loop system is confirmed by the experimental results. The result of this study is useful for the control design of a magnetic bearing system.     

Design of electrofusion joints and evaluation of fusion strength using fusion simulation technology

Fusion simulation is one of the key techniques in designing and producing electrofusion (EF) joints for gas distribution and in evaluating fusion joint integrity. This paper describes the result of a numerical simulation of a thermal fusion process, using the finite element method. A nonlinear heat transfer computer program was used to obtain the temperature profile of a large electrofusion joint at fusion. The effects of applied voltage, heating time, wire pitch, and ambient temperature were examined for designing a 150-mm EF joint. A method to shorten the cooling time was also investigated. The fusion condition range suitable for a 150-mm EF joint was found to be slightly narrower than that suitable for a 50-mm EF joint. Examination of the effect of wire pitch revealed that if the pitch is extremely large, thermal degradation starts in the resin close to the wire before the fusion-interface strength reaches the maximum value. We have developed a program to simulate the process of closing the gap between the pipe and the joint due to resin expansion and melting after the power is supplied.