Analysis of viscoelastic laminated composite plates

A micromechanics analysis is performed for the determination of the five independent elastic moduli of unidirectional fiber composites. By considering viscoelastic phases and by using the correspondence principle and the inversion of the Laplace transform, the five time-dependent functions which characterize the effective behavior of viscoelastic composites are established. The predicted time-dependent behavior is applied for the analysis of viscoelastic laminated plates. The resulting viscoelastic effects are shown, and comparison between the results obtained within the classical laminated plate theory and the first-order shear deformation theory is discussed.     

Synthesis of N,N-diethyl-N-{4-[(E)-(4-nitrophenyl)diazenyl]phenyl}amine via in situ diazotisation and coupling in supercritical carbon dioxide

The synthesis of azo dyes via a conventional aqueous-based diazotisation and coupling reaction requires the use of relatively high concentrations of mineral acids, which leads to high electrolyte concentrations in wastewater. Reported in this paper is an environmentally benign one-pot method for the synthesis of a nonionic azo dye, N,N -diethyl- N -{4-[( E )-(4-nitrophenyl)diazenyl]phenyl}amine, in supercritical carbon dioxide without using a mineral acid. The product yield increased significantly with temperature, with 91% theoretical yield afforded at 80 °C. The pressure of the system had little influence on product yield.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

程控电流源无需电源支持

工程实验室通常都配有各种电源设备、伏特计、函数信号发生器和示波器。然而．许多这样的工程实验室却缺少电流源。这令人感到非常遗憾，因为电流源有助于生成I-V（电流对电压）曲线，它能对电池进行充放电操作，对电源设备预加负荷，并可实现许多其他的应用。     

Analysis of the Datagram Congestion Control Protocol’s connection management procedures using the sweep-line method

State space explosion is a key problem in the analysis of finite state systems. The sweep-line method is a state exploration method which uses a notion of progress to allow states to be deleted from memory when they are no longer required. This reduces the peak number of states that need to be stored, while still exploring the full state space. The technique shows promise but has never achieved reductions greater than about a factor of 10 in the number of states stored in memory for industrially relevant examples. This paper discusses sweep-line analysis of the connection management procedures of a new Internet standard, the Datagram Congestion Control Protocol (DCCP). As the intuitive approaches to sweep-line analysis are not effective, we introduce new variables to track progress. This creates further state explosion. However, when used with the sweep-line, the peak number of states is reduced by over two orders of magnitude compared with the original. Importantly, this allows DCCP to be analysed for larger parameter values. Somsak Vanit-Anunchai was partially supported by an Australian Research Council Discovery Grant (DP0559927) and Suranaree University of Technology. Guy Edward Gallasch was supported by an Australian Research Council Discovery Grant (DP0559927).     

Polarization control in a vertical cavity surface emitting laser submitted to optical feedback

We study experimentally and theoretically two polarization effects in a vertical cavity surface emitting laser submitted to optical feedback. In a first experiment, we obtain flips between two linearly polarized laser modes up to a frequency of 50 MHz using an external cavity with a polarizer. In a second experiment, polarization self modulation is demonstrated up to a frequency of 2.6 GHz, using a quarter wave plate instead. Numerical calculations, based on a four levels model for the active medium, show a good agreement with the experiments.