影响掺矿渣的钢纤维砼强度的主要因素

研究结果表明 :水胶比、胶凝材料用量、钢纤维掺量、矿渣代水泥量对钢纤维砼强度影响显著。当矿渣取代水泥 10 %时 ,钢纤维砼强度最高。经试验选择出一个具有良好和易性和较高强度 (118MPa)的钢纤维砼配合比 ,为掺磨细矿渣的中含量超短异形钢纤维砼的设计和施工提供了试验依据     

Effect of temperature on the strength and conductivity of a deformation processed Cu-20%Fe composite

The high temperature (22–600 °C) properties were evaluated for a Cu-20%Fe composite deformation processed from a powder metallurgy compact. The ultimate tensile strengths decreased with increasing temperature but were appreciably better than those of similarly processed Cu at temperatures up to 450 °C. At 600 °C, the strength of Cu-20%Fe was only slightly better than that of Cu as a result of the pronounced coarsening of the Fe filaments. However, at temperatures of 300 and 450 °C, the strength of Cu-20%Fe is about seven and six times greater, respectively, than that of Cu, as compared to about a two fold advantage at room temperature. Therefore, Cu-20%Fe composites made by deformation processing of powder metallurgy compacts have mechanical properties much superior to those of similarly processed Cu at room temperature and at temperatures up to 450 °C. The pronounced decrease in electrical conductivity of deformation processed Cu-20%Fe as compared to Cu is attributed to the appreciable dissolution of Fe into the Cu matrix which occurred during the fabrication of the starting compacts where temperatures up to 675 °C were used. While the powder metallurgy compacts used for the starting material for deformation processing in this study did not lead to a high conductivity composite, the powder metallurgy approach should still be a viable one if processing temperatures can be reduced further to prevent the dissolution of Fe into the Cu matrix.     

Computation of the average power pattern of a reflector antennawith random surface errors and misalignment errors

To specify manufacturing tolerances of a reflector antenna, various errors such as random surface errors and misalignment errors must be considered at one time because superposition of the effects of those errors may not hold. Based on the Rahmat-Samii's formulation (1983), a method for computing efficiently the average power pattern of a reflector antenna with those errors is presented. Simulation results show that superposition of the effects of errors does not generally hold and demonstrate how those errors degrade the peak-gain and sidelobe levels     

Occurrence of correlation between occurrence of genital tract candidiasis in young girls and some subjective and objective examination parameters

The authors tried to find the correlation between the occurrence of genital tract candidiasis in adolescents and some subjective and objective examination parameters. The highest correlation rates were found for pudendal pruritus, lower abdominal pains and early applied antibiotic therapy material: 188 adolescent girls.     

Spontaneous hemorrhage of an adrenal cortical adenoma causing Cushing''s syndrome

A modified surgical splint for Le Fort I osteotomies with transverse expansion is presented. The splint is made of a transpalatal stainless steel bar with acrylic abutment against the palatal surface of the molar and bicuspid tooth. It is rigid and renders excellent retention. It causes minimal patient discomfort, and oral hygiene is hardly compromised.     

Pore‐free mold‐pattern‐transfer method for barrier ribs of HD PDPs

Abstract— Among various barrier‐rib manufacturing processes, the mold‐pattern‐transfer method has potential to reduce processing cost as well as the manufacture of high‐resolution pixels. In this study, the effects of major processing variables of the mold‐pattern‐transfer process on the formation of air‐trapped pores within barrier ribs were examined. The results indicated that with an optimum combination of the processing variables, barrier ribs without trapped defects can be produced, demonstrating the possibility of reducing the number of processing steps and costs of barrier ribs.