Cerebral microbleeds and cognitive decline in a hemodialysis patient: Case report and review of literature

Cerebral microbleeds (CMBs) are small hemosiderin deposits indicative of prior cerebral microscopic hemorrhage and previously thought to be clinically silent. Recent population‐based cross‐sectional studies and prospective longitudinal cohort studies have revealed association between CMB and cognitive dysfunction. In the general population, CMBs are associated with age, hypertension, and cerebral amyloid angiopathy. In the chronic kidney disease (CKD) population, diminished estimated glomerular filtration rate has been found to be an independent risk factor for CMB, raising the possibility that a uremic milieu may predispose to microbleeds. In the end‐stage renal disease (ESRD) population on hemodialysis, the incidence of microbleeds is significantly higher compared with a control group without history of CKD or stroke. We present an ESRD patient on chronic hemodialysis with a history of gradual cognitive decline and progressive CMBs. Through this case and literature review, we illustrate the need to develop detection and prediction models to treat this frequent development in ESRD patients.     

Improving the Reliability of Software-Defined Networks with Distributed Controllers Through Leader Election Algorithm and Colored Petri-Net

Wireless Personal Communications - Software-Defined Networks (SDNs) are developed to compensate the complicated function of the controlling parts of the given network elements and making the...     

Correction to: Cloud-based vehicular networks: a taxonomy,survey, and conceptual hybrid architecture

Wireless Networks - The original version of this article unfortunately contained a mistake in the title. The correct title has been published with this erratum.     

Imaging of two-dimensional unsaturated moisture flows in uncracked and cracked cement-based materials using electrical capacitance tomography

The development of visualizing tools to monitor unsaturated moisture flow in cement-based materials is of great importance, as most degradation processes in cement-based materials are connected to and take place in the presence moisture. This paper investigates the ability of electrical capacitance tomography (ECT) to image two-dimensional (2D) unsaturated moisture flow in cement-based materials. In ECT, the electrical permittivity distribution within an object is reconstructed based on measured capacitances between electrodes attached on the object’s surface. In a series of experiments, mortar specimens with and without discrete cracks were imaged with ECT during a 2D moisture ingress. The results show that ECT is able to monitor the evolution of the moisture flow, and to approximate the shape and position of the moisture front. These findings indicate that ECT is a viable method for monitoring and visualizing 2D unsaturated moisture flow in cement-based materials in the presence and absence of discrete cracks.     

A stochastic model for localized disturbances and its applications

A stochastic model for local disturbances, particularly for a temporal harmonic with random modulations in amplitude and/or phase, is proposed in this paper. Results for the second moment responses of a linear single-degree-of-freedom system to this type of stochastic loading demonstrate a significant change in response characteristics due to a small uncertainty. A local phenomenon may last much longer and resonance may be smeared to a broad range. Integrated with wavelet transform, the proposed approach may be used to model a random process with non-stationary frequency content. Especially, it can be effectively used for Monte Carlo simulation to generate large size of samples that have similar characteristics in time and frequency domains as a pre-selected mother sample has. The technique has a great potential for the case where uncertainty study is warranted but the available samples are limited.     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Continuous hydrolysis of olive oil by lipase in microporous hydrophobic membrane bioreactor

Continuous hydrolysis of olive oil byCandida cylindracea’s lipase was studied in a microporous hydrophobic membrane bioreactor. Olive oil and buffer solution, fed continuously through two compartments partitioned by membrane, caused reaction at the interface of lipase-adsorbed membrane and buffer solution. Fatty acid was obtained in a single phase without being mixed with components of other phases. At all mean residence times, countercurrent flow mode was superior to cocurrent one. The lipase was adsorbed onto the membrane, and its adsorption was suggested to be partially specific from the experiments with enzymes having various levels of purity. The percent hydrolysis depended hyperbolically on the interfacial enzyme concentration. The hydrolysis seemed to be limited by diffusion of fat or fatty acid through the micropores of the membrane at higher interfacial enzyme concentrations. The lipase was stabilized significantly by glycerol added to the buffer solution. Satisfactory performance of the membrane bioreactor was obtained in a longterm continuous operation which lasted for 24 days by feeding buffer-glycerol (18.0%) solution over the adsorbed lipase. The operational half-life of the adsorbed enzyme was 15 days at 40 C.     

An automated coding and classification system with supporting database for effective design of manufacturing systems

The philosophy of group technology (GT) is an important concept in the design of flexible manufacturing systems and manufacturing cells. Group technology is a manufacturing philosophy that identifies similar parts and groups them into families. Beside assigning unique codes to these parts, group technology developers intend to take advantage of part similarities during design and manufacturing processes. GT is not the answer to all manufacturing problems, but it is a good management technique with which to standardize efforts and eliminate duplication. Group technology classifies parts by assigning them to different families based on their similarities in: (1) design attributes (physical shape and size), and/or (2) manufacturing attributes (processing sequence). The manufacturing industry today is process focused; departments and sub units are no longer independent but are interdependent. If the product development process is to be optimized, engineering and manufacturing cannot remain independent any more: they must be coordinated. Each sub-system is a critical component within an integrated manufacturing framework. The coding and classification system is the basis of CAPP and the functioning and reliability of CAPP depends on the robustness of the coding system. The proposed coding system is considered superior to the previously proposed coding systems, in that it has the capability to migrate into multiple manufacturing environments. This article presents the design of a coding and classification system and the supporting database for manufacturing processes based on both design and manufacturing attributes of parts. An interface with the spreadsheet will calculate the machine operation costs for various processes. This menu-driven interactive package is implemented using dBASE-IV. Part Family formation is achieved using a KAMCELL package developed in TURBO Pascal.