A process-dependent real-time controller for sequencing batch reactor plants: results of full-scale operation.

This paper presents results of a research project, in which a process-dependent real-time control (RTC) strategy for a sequencing batch reactor plant was realised in full-scale. The cycle controller is based on NH4 analysers, NO3 probes, TSS probes and sludge level probes. With this new RTC strategy it was possible to increase the treatment capacity by 50%. By implementation of the new controller the TN, TP and NH4-N treatment efficiency could be improved significantly, too. The treatment efficiency concerning COD is comparable.     

Effects of sudden pressure changes in the surrounding gas phase on flow properties of bulk solids

The variation in the behaviour of bulk solids as a result of sudden pressure changes in the surrounding gas phase is of interest in the application of lock hoppers for transfer of bulk solids into pressure vessels. By using such sluice systems, problems occur due to consolidation of the pressurized bulk solids. This paper presents the results of experimental and theoretical research, which allow to describe the influence of several parameters on pressure compensation and the degree of consolidation. With reference to the forces and mechanisms responsible for consolidation, it is possible to describe the different consolidation behaviour of incompressible (limestone) and compressible (hard coal) bulk solids.     

The effect of lidocaine on growth of cells of head and neck squamous cell carcinoma

The relation between 21 absolute body dimensions as well as 20 anthropometric indices and the length as well as the regularity of the menstrual cycle have been investigated in 156 patients of the hormone ambulance of the I. Universit?ts-Frauenklinik in Vienna. It turned out, that the length as well as the regularity of the menstrual cycle significantly negatively with the amount of the subcutaneous fat tissue. With an increasing amount of adipose tissue, the cycle became shorter and more regular. The importance of the subcutaneous fat tissue as a secondary hormonal gland has been discussed as one cause for these significant connections. Regarding the length- and height dimensions and the menstrual cycle patterns, no statistically significantly relationship could be observed between these two trait system. This is also true for the relationship between body built and the bleeding duration.     

Tendon layout optimisation through configurational forces equilibration in plane stress analysis of prestressed concrete structures

The focus of this work is a novel application of configurational forces to tendon layout optimisation problems in prestressed concrete beams. To this end, the application of the method of the configurational forces is extended to two-dimensional plane stress analysis. The optimum tendon position is obtained by iteratively arriving at vanishing configurational forces. The performance of the optimisation algorithm is illustrated by means of numerical examples.     

Creep of thermally aged SnAgCu-solder joints

The creep behaviour of Sn96.5Ag3.5- and Sn95.5Ag3.8Cu0.7-solder was studied specifically for its dependence on technological and environmental factors. The technological factors considered were typical cooling rates and pad metallizations for solder joints in electronic packaging. The environmental factors included microstructural changes as a result of thermal aging of solder joints. Creep experiments were conducted on three types of specimens—flip–chip joints, PCB solder joints and bulk specimens. flip–chip specimens were altered through the selection of various under bump metallizations (Cu vs. NiAu), cooling rates (40 K/min vs. 120 K/min), and thermal storage (24 h, 168 h, and 1176 h at 125 °C). PCB solder joints were studied by using a copper pin soldered into a thru-hole connection on a printed circuit board having a NiAu metallization. Bulk specimens contained the pure alloys. The creep behaviour of the SnAg and SnAgCu solders varied in dependence of specimen type, pad metallization and aging condition. Constitutive models for SnAg and SnAgCu solders as they depend on the reviewed factors are provided.     

Microstructure and creep behaviour of eutectic SnAg and SnAgCu solders

The paper presents creep data, that was gained on specimens of different microstructures. The three specimen types have been flip chip solder joints, pin trough hole solder joints and standard bulk solder specimens. The bulk solder specimen was a dog-bone type specimen (diameter=3 mm, LENGTH=117 mm). The pin trough hole solder joint consisted on a copper wire that was soldered into a hole of a double sided printed circuit board (thickness 1.5 mm). The flip chip solder joint specimen consisted of two silicon chips (4 mm × 4 mm), which were connected by four flip chip joints (one on each corner). SnAg and SnAgCu flip chip bumps (footprint 200 μm × 200 μm, joint height 165–200 μm, centre diameter 90…130 μm) were created by printing solder paste.Constant–load creep tests were carried out on all three specimen types at temperatures between 5 and 70 °C. Creep data was taken for strain rates between 10⁻¹⁰ and 10⁻³ s⁻¹. The specimens were tested in “as cast” condition and after thermal storage.The microstructural properties of the bulk specimens and real solder joints were examined using metallographic sectioning, optical microscopy techniques, and SEM-microprobe analysis. The results of the microstructural analysis were related to the investigated mechanical properties of the solders. Models of SnAg3.5 and SnAg4Cu0.5, that can be used with the ANSYS FEM software package, will be presented.     

The effect of downscaling the dimensions of solder interconnects on their creep properties

The creep behaviour of solders is an important input for accurate material models for FE-analysis of electronic assemblies. Usually the mechanical behaviour of solders has been determined by tensile tests on bulk solder specimens. Although performing these tests is not complicated and the results are easy to interpret, one of the key problems lies in the fact that solder joints are very small and, therefore, cannot be represented by large tensile specimens. The paper describes the attempts to gain deformation data on ultra small solder joints. It compares creep data that was experimentally gained on bulky samples and on small solder joints.     

Brennstoffzellen

For two applications of fuel cells (SOFC and IMFC) system configurations and energy balances are presented. A decentralized combined heat and power plant on SOFC basis can be designed as a flexible system with high efficiency. A drive system with methanol reformer and fuel cell (IMFC) in comparison with a natural gas combustion engine has lower energy comsumption and much lower emissions.     

A ¹⁸F-labeled fluorobutyl-substituted spirocyclic piperidine derivative as a selective radioligand for PET Imaging of sigma₁ receptors

In this study, we synthesized and evaluated a new spirocyclic piperidine derivative 3 , containing a 4‐fluorobutyl side chain, as a PET radioligand for neuroimaging of σ₁ receptors. In vitro, compound 3 displayed high affinity for σ₁ receptors (K_i=1.2 nM ) as well as high selectivity. [¹⁸F] 3 radiosynthesis was performed from the corresponding tosylate precursor, with high radiochemical yield (45–51 %), purity (>98 %), and specific activity (>201 GBq μmol^?1). Metabolic stability of [¹⁸F] 3 in the brain of CD‐1 mice was verified, and no penetration of peripheral radiometabolites into the cerebral tissue was observed. Results of ex vivo autoradiography revealed that the distribution of [¹⁸F] 3 in the brain corresponded to regions with high σ₁ receptor density. The highest region‐specific total‐to‐nonspecific ratio was determined in the facial nucleus (4.00). Biodistribution studies indicated rapid and high levels in brain uptake of [¹⁸F] 3 (2.2 % ID per gram at 5 min p.i.). Pre‐administration of haloperidol significantly inhibited [¹⁸F] 3 uptake into the brain and σ₁ receptor‐expressing organs, further confirming in vivo target specificity.     

纳米CaCO3合成及原位改性的研究

在旋转填充床反应器中合成了纳米CaCO3悬浮液,利用pH计跟踪Ca(OH)2碳化反应过程,研究了碳化反应过程原理。结果表明：旋转填充床能极大地强化相间传质与微观混合,提高体系中CaCO3的过饱和度,增大其成核及生长速率。加入适当的添加剂对纳米CaCO3进行原位改性;利用TEM照片研究了原位改性过程中纳米CaCO3的成核生长机理,并考察了添加剂的作用机理。