Nanoscale fine-tuning of porosity of carbide-derived carbon prepared from molybdenum carbide

Micro- and mesoporous carbide-derived carbon (CDC) was synthesised from molybdenum carbide (Mo₂C) powder by gas phase chlorination in the temperature range from 400 to 1200 °C. Analysis of XRD results show that C(Mo₂C), chlorinated at 1200 °C, consist mainly on graphitic crystallites of mean size, L_a = 9 nm and L_c = 7.5 nm. The first-order Raman spectra showed the graphite-like absorption peak at ∼1587 cm⁻¹ and the disorder-induced (D) peak at ∼1348 cm⁻¹. The low-temperature N₂ adsorption experiments were performed and a specific surface area up to 1855 m² g⁻¹ and total pore volume up to 1.399 cm³ g⁻¹ were obtained. Sorption measurements showed the presence of both micro- and mesopores after chlorination at 400-900 °C and only mesopores after chlorination at 1000°-1200 °C. Stepwise formation of micro- and mesopores was achieved and the peak pore size can be shifted from 0.8 nm up to 4 nm by increasing the chlorination temperature.     

Electrochemical and gas phase parameters of cathodes for intermediate temperature solid oxide fuel cells

A series of cyclic voltammetry, chronoamperometry and electrochemical impedance experiments have been carried out in order to investigate the effect of cathode composition and porosity on the electrochemical characteristics of strontium-doped lanthanum, praseodymium and gadolinium cobaltite cathodes. The impedance responses at different electrode potentials of the half cell and symmetric single cell setups are compared and analyzed by the equivalent circuit modeling method. The deconvolution of impedance spectra for single cell cathode and anode reactions contributions based on the results of simultaneous analysis of half cells and symmetric single cells has been made by differential impedance real part vs. ac frequency plot analysis method. Noticeable influence of cathode chemical composition, meso-porosity and macro-porosity on the electrochemical activity of the oxygen electroreduction has been demonstrated. Seeming activation energy values have been calculated and discussed.     

Characterisation of activated nanoporous carbon for supercapacitor electrode materials

Commercial nanoporous carbon RP-20 was activated with water vapor in the temperature range from 950 °C to 1150 °C. The XRD analysis was carried out on nanoporous carbon powder samples to investigate the structural changes (graphitisation) in modified carbon that occurred at activation temperatures T ? 1150 °C. The first-order Raman spectra showed the absorption peak at 1582 cm⁻¹ and the disorder (D) peak at 1350 cm⁻¹. The low-temperature N₂ adsorption experiments were performed at −196 °C and a specific surface area up to 2240 m²g⁻¹ for carbon activated at T = 1050 °C was measured. The cell capacitance for two electrode activated nanoporous carbon system advanced up to 60 F g⁻¹ giving the specific capacitance ∼240 F g⁻¹ to one electrode nanoporous carbon ∣1.2 M (C₂H₅)₃CH₃NBF₄ + acetonitrile solution interface. A very wide region of ideal polarisability for two electrode system (∼3.2 V) was achieved. The low frequency limiting specific capacitance very weakly increases with the rise of specific area explained by the mass transfer limitations in the nanoporous carbon electrodes. The electrochemical characteristics obtained show that some of these materials under discussion can be used for compilation of high energy density and power density non-aqueous electrolyte supercapacitors with higher power densities than aqueous supercapacitors.     

On the porosity of polypyrrole films

Polypyrrole (PPy) films doped with anions of various size, charge and chemical nature (inorganic, surfactant, with aromatic ring) were electrochemically synthesized and investigated by low-temperature N₂ sorption experiments at −196 °C. The specific surface area, total pore volume, average pore radius, pore size distribution and other parameters for oxidized PPy films using dodecylsulfate, 2-naphthalene sulfonate, 1,5-naphthalene disulfonate, poly(4-styrenesulfonate), tosylate, perchlorate, nitrate and chloride as dopant ions, were calculated. The obtained data show that although the average pore radius of investigated mesoporous PPy films (17–19 Å) is practically independent of the dopant anion used, however the latter determines the total pore volume and specific surface area values in different PPy materials investigated. As the total pore volumes for PPy films doped with large amphiphilic anions show the smallest values, the corresponding values for PPy/small inorganic anions, are up to 2 times higher.