Cooperative behavior of various agents in dynamic environment

The multi-agent model is a model in which agents with limited ability cooperate each other to accomplish a goal. In this paper, we introduce a multi-agent model in which agents are created to imitate real ants. There are two different type of agents, each type of which has a particular task. We designed agents to communicate each other by using pheromone considering noise. On this model, we observed cooperative behavior of agents and evaluated conditions to make an order of behavior in the model.     

Analysis of shielded microstrip lines with arbitrary metallizationcross section using a vector finite element method

The finite element method (FEM) with the high-order mixed-interpolation-type triangular element is used to solve the problem of practical microstrip lines with arbitrary metallization cross section. Analyses are carried out to produce the frequency characteristics of propagation constant, characteristic impedance, and attenuation constant of shielded microstrip lines with rectangular, trapezoidal, and semi-trapezoidal strip cross sections. A comparison of the numerical results with those of the existing results shows good agreement and thus verifies the versatility of the FEM. Also, the numerical results show the effects of the metallization cross sections on the transmission properties and thus emphasize the importance of considering the practical microstrip configurations in the design of miniaturized MMICs     

Quantitative trait loci affecting 4-nitroquinoline 1-oxide-induced tongue carcinogenesis in the rat

The incidence of tongue carcinomas (TCs) induced by oral administration of 4-nitroquinoline 1-oxide in rats is strain dependent. The inbred Dark-Agouti (DA) strain showed a much higher susceptibility to large mass-forming infiltrative TCs than did the Wistar-Furth (WF) strain. Our previous study (M. Kitano et al, Jpn. J. Cancer Res., 87: 1097-1101, 1996) on crosses between these two strains postulated a dominant susceptibility gene in DA and a dominant resistance gene in WF rats. The present study mapped these loci by analyzing the backcrosses to each parent with simple sequence repeat polymorphisms. Five quantitative parameters were analyzed: (a) the number of TCs > 5 mm in diameter; (b) the total number of TCs per rat; (c) the diameter of the largest TCs (DTCmax values); (d) the number of non-TC cancers per rat; and (e) and the number of cancers of any site per rat. All of these parameters were closely correlated (P < 0.0001). DA rats had a semidominant gene (Stc1) favoring the development of 4-nitroquinoline 1-oxide-induced cancers on chromosome 19, closely linked to D19Mit9. Peak linkage was observed 4 cM distal from D19Mit9, with a logarithm of the odds (lod) score of 5.72 for the number of large TCs and 6.08 for the DTCmax. On the other hand, WF rats had a semidominant gene (Rtc1) mapped between D1Mit1 and D1Mit3, approximately 20 cM from D1Mit1, with a peak lod score of 3.30 for both the number of large TCs and the DTCmax. The main effect of Rtc1 seemed to be to reduce the size of the TCs. The action of these genes was dose dependent and cooperative. The final incidence of TC in DA, WF, F1, and backcross rats seemed to be explained by combinations of genotype at these two loci. Possible candidate genes for Stc1 and Rtc1 are discussed.     

On approximate solutions for the deformation of plane anisotropic beams

Plane deformation of anisotropic beams with narrow rectangular cross sections exhibits coupling of stretching, bending and transverse shearing. For anisotropic cantilever beams with a stiff end-cap under end forces and an end couple, assessments were made for approximate solutions by comparing these with numerically exact finite element (FE) solutions. Specific attention is given to point-wise or approximate satisfaction of the end-fixity conditions. As approximate methodologies, (i) the elementary polynomial form of Airy's stress function for the plane stress problem in a rectangular region, (ii) a Timoshenko-type beam theory, and (iii) the Bernoulli-Euler beam theory were selected. Among these, only the polynomial form of Airy's stress function violates the point-wise end-fixity conditions. Both the polynomial Airy stress function and the Timoshenko-type beam theory successfully model the effects of transverse shear deformation and the coupling of stretching and transverse deflection. Analytical solutions demonstrate that the normal shear coupling effect increases linearly with the thickness-to-span ratios in axial normal stress and axial displacement, while the coupling manifests quadratically in transverse displacement. The comparison of end displacements with the numerically exact FE solutions indicates that the polynomial form of Airy's stress function is no better than the Timoshenko-type beam theory. Similar conclusions were reached for the problem of uniformly loaded cantilever beams. It has been found that the accurate prediction of the deformation of thick anisotropic beams with significant normal-shear coupling requires the use of higher order theories.     

The effect of gas atmospheres on resistivity of indium tin oxide films at high temperature

The effects of heat treatment in Q₂, O₂ and N₂, and Ar gases on the high temperature (500 C) electrical resistivity of indium tin oxide (ITO) film 52 nm thick prepared by chemical spray pyrolysis method were studied. The partial oxygen pressure effect on the resistivity was found to be to . The resistivity changes for cyclic exchange of O₂ by Ar gas at 500 C. These lead to the conclusion that chemisorption of oxygen atoms in the film surface is dominant for this thin film, for thicker films such as 640 nm oxygen diffusion is found to occur. The Langmuir model of the monolayer isothermal adsorption of oxygen atoms in the surface is applicable to the rapid change of resistivity.     

Net shape formation of sub-micron alumina with reduced flaws by high-speed centrifugal compaction process

A new compacting method for powder materials is presented. High-Speed Centrifugal Compaction Process (HCP) utilizes centrifugal force of about 10,000 g for the compaction. HCP is suitable for net shape compaction of fine sub-micron and nano-powders. HCP possesses a unique compacting mechanism that is different from other colloidal processes including Pressure Casting (PC), and has a number of useful characteristics. HCP has a higher compacting speed than PC, wide applicability for net shape formation, as well as a defect removing function. Because of homogeneous and flawless green microstructure, HCP alumina shows superior sinterability and higher strength and hardness than most of other aluminas. This article is based on a presentation made in the symposium “The 3rd KIM-JIM Joint Symposium on Advanced Powder Materials“, held at Korea University, Seoul, Korea, October 26–27, 2001 under auspices of The Korean Institute of Metals and Materials and The Japan Institute of Metals.     

Alteration of substrate specificity of cholesterol oxidase from Streptomyces sp. by site-directed mutagenesis

Despite the structural similarities between cholesterol oxidasefrom Streptomyces and that from Brevibacterium, both enzymesexhibit different characteristics, such as catalytic activity,optimum pH and temperature. In attempts to define the molecularbasis of differences in catalytic activity or stability, substitutionsat six amino acid residues were introduced into cholesteroloxidase using site-directed mutagenesis of its gene. The aminoacid substitutions chosen were based on structural comparisonsof cholesterol oxidases from Streptomyces and Brevibacterium.Seven mutant enzymes were constructed with the following aminoacid substitutions: L117P, L119A, L119F, V145Q, Q286R, P357Nand S379T. All the mutant enzymes exhibited activity with theexception of that with the L117P mutation. The resulting V145Qmutant enzyme has low activities for all substrates examinedand the S379T mutant enzyme showed markedly altered substratespecificity compared with the wild-type enzyme. To evaluatethe role of V145 and S379 residues in the reaction, mutantswith two additional substitutions in V145 and four in S379 wereconstructed. The mutant enzymes created by the replacement ofV145 by Asp and Glu had much lower catalytic efficiency forcholesterol and pregnenolone as substrates than the wild-typeenzyme. From previous studies and this study, the V145 residueseems to be important for the stability and substrate bindingof the cholesterol oxidase. In contrast, the catalytic efficiencies(k_cat/K_m) of the S379T mutant enzyme for cholesterol and pregnenolonewere 1.8- and 6.0-fold higher, respectively, than those of thewild-type enzyme. The enhanced catalytic efficiency of the S379Tmutant enzyme for pregnenolone was due to a slightly high k_catvalue and a low K_m value. These findings will provide severalideas for the design of more powerful enzymes that can be appliedto clinical determination of serum cholesterol levels and assterol probes.     

New Preparation Method of CdS Clusters Encapsulated in Y-Type Zeolites

CdS clusters encapsulated in Y-type zeolite were prepared by a novel technique with non-aqueous systems. The mechanical mixture of CdCl₂· 2.5H₂O crystal with Y-type zeolite was heated at 773 K, followed by the H₂S treatment at 373 K, resulting in the formation of CdS clusters with the size <2.3 nm.