Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.     

A novel brain-derived member of the epidermal growth factor family that interacts with ErbB3 and ErbB4

The availability of an analgesic compound devoid of the side effects associated with the commonly used opioid and nonsteroidal antiinflammatory drugs would be useful during the perioperative period. Although adenosine has analgesic and anesthetic-sparing properties, it also produces dose-dependent cardiovascular depression. Inhibitors of adenosine kinase may be able to provide analgesia without producing acute cardiovascular or respiratory depression. This preliminary study investigated the effects of a novel adenosine kinase-inhibiting drug, GP683, on the minimum alveolar anesthetic concentration (MAC) of desflurane in dogs. Seven mongrel dogs were administered one of three different GP683 dose regimens (or the solvent) by intravenous infusion on separate occasions according to a cross-over study design. After determining the baseline desflurane MAC value, GP683 was infused at 75, 150, or 300 microg x kg(-1) x min(-1) for 5 min as a loading dose, followed by 15, 30, or 60 microg x kg(-1) x min(-1) for an additional 85 min to maintain a stable plasma drug level. The desflurane MAC was redetermined 30-90 min after starting the study drug or vehicle infusion, and 30-90 min and 120-180 min after termination of the infusion. Cardiovascular variables and plasma concentrations of GP683 were determined at specific intervals before, during, and after the MAC determinations. The three GP683 dose regimens produced 22%, 31%, and 50% decreases in the desflurane MAC, respectively. In addition, there was good correlation between the decrease in desflurane MAC and the plasma GP683 concentration (r = -0.78). Although the mean arterial pressure (MAP) was decreased up to 25% by the highest infusion rate of GP683, adjustments in the desflurane concentration to an equi-MAC value resulted in normalization of the MAP values. Furthermore, GP683 produced no changes in heart rate. In conclusion, the adenosine kinase-inhibiting drug, GP683, produced dose-dependent decreases in the desflurane MAC of dogs without producing untoward hemodynamic changes. IMPLICATIONS: An investigational drug (GP683) that can increase the levels of an important endogenous substance in the body (adenosine) has been found to decrease the anesthetic requirement in dogs without producing adverse effects on the cardiovascular system.     

Modulation characteristic of waveguide-type optical frequency combgenerator

We report the modulation characteristics of a waveguide-type optical frequency comb generator (WG-OFCG) with the advantages of compactness, high modulation index and low driving power. The characteristics of the optical frequency comb (OFC) generated when the modulation index exceeds 2π are discussed. The power of the modulation sidebands was measured by the optical heterodyne method with an external-cavity laser as a local oscillator. The dependence of the modulation index of the WG-OFCG on the modulation frequency up to 40 GHz was measured. The generation span of the OFC at the modulation frequency detuned from an integer multiple of the free spectral range (FSR) is discussed     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

Infrared sensing properties of positive temperature coefficient thermistors with large temperature coefficients of resistivity

Infrared (IR) detecting elements were prepared using positive temperature coefficient (PTC) thermistors with large temperature coefficients of resistivity (α). Their compositions were denoted as Ba_1−x Sr _x Nb_0.003Ti_0.997O₃ + 1 mol % TiO₂ + 0.07 mol %MnO (x=0, 0.2), and their temperature coefficients of resistivity were 78 and 50% K⁻¹, respectively. Their IR sensing properties were measured under the self-regulating heating conditions, and were compared with those of a detector with small α (18 % K⁻¹). It was shown that large α was effective for controlling the element temperature by self-regulating heating and for improving sensitivity. The responsivity,R _v of the element withx=0.2 was 980 VW⁻¹, and was as large as those of pyroelectric detectors. Expressions which normalize the sensitivity and the thermal time constant were derived. From these expressions, criteria for improving some IR sensing properties were obtained.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

Interconnected power systems with superconducting magnetic energy storage

The objective of this work is to discuss the concept of back‐to‐back interconnection systems with energy storage, especially with a Superconducting Magnetic Energy Storage (SMES) incorporated into a back‐to‐back DC link. In this case, each converter of the back‐to‐back system is used as a power conditioning system for the SMES coils. Since the AC–DC converter can be designed independently of the frequency of the power system, a two‐way switch is connected to the AC side of each converter. This two‐way switch can select the interconnected power systems. By using the two‐way switches, this system can provide the stored energy in the SMES system to each interconnected power system through two AC–DC converters. For instance, lower‐cost power of each power network can be stored through two converters during the off‐peak hours and made available for dispatch to each power network during periods of demand peak. Then this system increases the reliability of electric power networks and enables the economical operations depending on the power demand. This paper describes the unique operations of the back‐to‐back interconnection with SMES and discuses the optimal SMES configuration for a 300‐MW‐class back‐to‐back interconnection. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(2): 37–43, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20482