Bias-temperature instabilities of polysilicon gate HfO/sub 2/ MOSFETs

Bias-temperature instabilities (BTI) of HfO/sub 2/ metal oxide semiconductor field effect transistors (MOSFETs) have been systematically studied for the first time. NMOS positive BTI (PBTI) exhibited a more significant V/sub t/ instability than that of PMOS negative BTI (NBTI), and limited the lifetime of HfO/sub 2/ MOSFETs. Although high-temperature forming gas annealing (HT-FGA) improved the interface quality by passivating the interfacial states with hydrogen, BTI behaviors were not strongly affected by the technique. Charge pumping measurements were extensively used to investigate the nature of the BTI degradation, and it was found that V/sub t/ degradation of NMOS PBTI was primarily caused by charge trapping in bulk HfO/sub 2/ rather than interfacial degradation. Deuterium (D/sub 2/) annealing was found to be an excellent technique to improve BTI immunity as well as to enhance the mobility of HfO/sub 2/ MOSFETs.     

Analysis of XANES for identification of highly dispersed transition metal oxides on supports

XANES of vanadium and niobium oxide on silica or alumina have been analyzed quantitatively by a deconvolution technique. Based on the results for reference compounds, local structures of supported vanadium and niobium species were identified. The composition was estimated from difference spectra for the samples which consisted of two kinds of species.     

Measurements of interdiffusion coefficients in metallic melts at high temperature under horizontal static magnetic field

Application of a uniform magnetic field is expected to be a promising substitute for utilization of the microgravity environment from the view point of damping of convection in electrically conductive fluid. Measurements of interdiffusion coefficients in In₈₀Sn₂₀, Sn₉₅Pb₅, and Ge_97.5Si_2.5 melts were performed in a wide temperature range up to 1473 K under a uniform and horizontal static magnetic field of 1 T by utilizing the magnetohydrodynamics effect in these melts.     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

An Application of Silica‐Based Monolithic Membrane Emulsification Technique for Easy and Efficient Preparation of Uniformly Sized Polymer Particles

Summary: Uniformly sized polymer particles were prepared by an emulsification and polymerization technique utilizing a silica monolithic membrane, namely the “silica monolithic membrane emulsification technique”. In this paper, we utilized silica monolithic membrane as a device for the preparation of uniformly sized polymer particles. A mixture of monomers, diluents and oil‐soluble initiator was emulsified into a continuous medium through the silica monolithic membrane and polymerized. The particles obtained had a higher size uniformity than that of particles prepared by previously reported membrane emulsification techniques, such as the Shirasu Porous Glass (SPG) emulsification technique. Through the silica monolithic membrane emulsification technique, we could prepare particles having availability as a possible packing material for solid‐phase extraction (SPE) and high performance liquid chromatography (HPLC).

SEM photograph of silica particles prepared through capillary plate membrane.     

Comparisons of computed mobile phone induced SAR in the SAM phantom to that in anatomically correct models of the human head

The specific absorption rates (SAR) determined computationally in the specific anthropomorphic mannequin (SAM) and anatomically correct models of the human head when exposed to a mobile phone model are compared as part of a study organized by IEEE Standards Coordinating Committee 34, Sub-Committee 2, and Working Group 2, and carried out by an international task force comprising 14 government, academic, and industrial research institutions. The detailed study protocol defined the computational head and mobile phone models. The participants used different finite-difference time-domain software and independently positioned the mobile phone and head models in accordance with the protocol. The results show that when the pinna SAR is calculated separately from the head SAR, SAM produced a higher SAR in the head than the anatomically correct head models. Also the larger (adult) head produced a statistically significant higher peak SAR for both the 1- and 10-g averages than did the smaller (child) head for all conditions of frequency and position.     

MOCVD Growth of Erbium Monoantimonide Thin Film and Nanocomposites for Thermoelectrics

We report the growth of erbium monoantimonide (ErSb) thin films on indium antimonide (100) substrates by low-pressure metalorganic chemical vapor deposition. The growth rate of ErSb thin films shows strong dependency on the growth temperature and the Sb/Er precursor molar flow rate ratio. Scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray diffractometry (XRD) were employed to study the ErSb thin films grown under the growth conditions that gave the maximum growth rate in the range we investigated. We also report the growth of two types of nanocomposites in which ErSb nanocolumns or nanoslabs with lengths ~500 nm and diameters 20 nm to 30 nm are embedded in Zn-doped InGaSb (ErSb/InGaSb:Zn) and ErSb nanoparticles with diameters of ~30 nm are embedded in Zn-doped InSbAs (ErSb/InSbAs:Zn). These nanocomposites were intended to increase phonon scattering in a mid-to-long phonon wavelength range to reduce lattice thermal conductivity. We used time-domain thermoreflectance to measure total thermal conductivity for the two types of nanocomposites, obtaining 4.0 ± 0.6 W/mK and 6.7 ± 0.8 W/mK for the ErSb/InAsSb:Zn and ErSb/InGaSb:Zn nanocomposites, respectively, which suggests that the thermal conductivity was close to or slightly smaller than the alloy limit of the two ternary alloy hosts. The two nanocomposites were further studied by transmission electron microscopy (TEM) to reveal their microscopic features and by XRD to assess their crystalline structures.     

Characteristics of hydrogen-assisted intergranular fatigue crack growth in interstitial-free steel: role of plastic strain localization

The behavior of intergranular fatigue crack growth in an interstitial-free (IF) steel in a hydrogen environment was investigated at different frequencies. Focusing on the plastic strain localization, we observed details of the striation-like feature on the intergranular fracture surface, slip behavior around microvoids, and crystallographic orientation gradient underneath the fracture surface. It was determined that the intergranular fatigue crack growth mechanism in the IF steel is microvoid formation at the crack tip and subsequent coalescence with the crack. Moreover, it was found that the grain boundaries, acting as propagation paths, suffer from pre-damage arising from plastic strain localization near the grain boundaries even before the main crack propagates to a certain location. Therefore, fatigue cracks in a hydrogen environment easily propagate to the grain boundaries. The frequency dependence of fatigue crack growth in the hydrogen environment is significantly smaller than that in a low carbon steel, probably because of the frequency dependence of the pre-damage evolution behavior.     

Mumefural and related HMF derivatives from Japanese apricot fruit juice concentrate show multiple inhibitory effects on pandemic influenza A (H1N1) virus

Fruit-juice concentrate of Japanese apricot (Prunus mume Sieb. et Zucc.) has been shown to be effective against influenza A infection in MDCK cells. In this study, we isolated five components from the fruit-juice concentrate of Japanese apricot, 5-(hydroxymethyl)-2-formylfuran (HMF), 1-[5-(2-formylfuryl)methyl]dihydrogen 2-hydroxypropane-1,2,3-tricarboxylate (mumefural, MF), 2-[5-(2-formylfuryl)methyl]dihydrogen 2-hydroxypropane-1,2,3-tricarboxylate (MF‘), 1-[5-(2-formylfuryl)methyl]hydrogen 1-hydroxyethane-1,2-dicarboxylate (MA1) and 2-[5-(2-formylfuryl)methyl]hydrogen 1-hydroxyethane-1,2-dicarboxylate (MA2), and investigated their inhibitory activities against the novel influenza A/Narita/1/2009 (H1N1) pandemic virus hemagglutinin and neuraminidase functions, which are essential for viral attachment and budding, respectively. An hemagglutination inhibition assay indicated that MF and MF‘ were effective at minimum hemagglutination concentrations of 3.1 and 6.3 mM, respectively. An inhibition study for sialidase activity of the neuraminidase spike showed that MF was the most active anti-sialidase compound with an IC₅₀ value of 0.21 ± 0.01 mM, followed by MA2 (IC₅₀, 0.71 ± 0.09 mM), MA1 (IC₅₀, 1.64 ± 0.31 mM) and MF‘(IC₅₀, 1.62 ± 0.22 mM). Furthermore, MF was shown to inhibit the growth of the pandemic virus in a dose-dependent manner (62 ± 3% inhibition at 5 mM). The results suggest that MF, a citric acid ester linked to HMF at the 1-position of the propane backbone, might be a lead compound for the development of anti-influenza A inhibitors.