Resource management in UAV-assisted MEC: state-of-the-art and open challenges

Wireless Networks - Unmanned aerial vehicles (UAV) have been widely used in various fields because of their high mobility and portability. At the same time, due to the rapid development of...     

Coil‐Type Asymmetric Supercapacitor Electrical Cables

Cable‐shaped supercapacitors (SCs) have recently aroused significant attention due to their attractive properties such as small size, lightweight, and bendability. Current cable‐shaped SCs have symmetric device configuration. However, if an asymmetric design is used in cable‐shaped supercapacitors, they would become more attractive due to broader cell operation voltages, which results in higher energy densities. Here, a novel coil‐type asymmetric supercapacitor electrical cable (CASEC) is reported with enhanced cell operation voltage and extraordinary mechanical‐electrochemical stability. The CASECs show excellent charge–discharge profiles, extraordinary rate capability (95.4%), high energy density (0.85 mWh cm⁻³), remarkable flexibility and bendability, and superior bending cycle stability (≈93.0% after 4000 cycles at different bending states). In addition, the CASECs not only exhibit the capability to store energy but also to transmit electricity simultaneously and independently. The integrated electrical conduction and storage capability of CASECS offer many potential applications in solar energy storage and electronic gadgets.     

Interlayer Engineering of Molybdenum Trioxide toward High‐Capacity and Stable Sodium Ion Half/Full Batteries

Orthorhombic molybdenum trioxide (MoO₃) is one of the most promising anode materials for sodium‐ion batteries because of its rich chemistry associated with multiple valence states and intriguing layered structure. However, MoO₃ still suffers from the low rate capability and poor cycle induced by pulverization during de/sodiation. An ingenious two‐step synthesis strategy to fine tune the layer structure of MoO₃ targeting stable and fast sodium ionic diffusion channels is reported here. By integrating partially reduction and organic molecule intercalation methodologies, the interlayer spacing of MoO₃ is remarkably enlarged to 10.40 Å and the layer structural integration are reinforced by dimercapto groups of bismuththiol molecules. Comprehensive characterizations and density functional theory calculations prove that the intercalated bismuththiol (DMcT) molecules substantially enhanced electronic conductivity and effectively shield the electrostatic interaction between Na⁺ and the MoO₃ host by conjugated double bond, resulting in improved Na⁺ insertion/extraction kinetics. Benefiting from these features, the newly devised layered MoO₃ electrode achieves excellent long‐term cycling stability and outstanding rate performance. These achievements are of vital significance for the preparation of sodium‐ion battery anode materials with high‐rate capability and long cycling life using intercalation chemistry.     

Attitude dynamics of coupled spacecraft undergoing fuel transfer

Multibody System Dynamics - This paper represents an explicit analytical solution for attitude dynamics of spacecraft combination during on-orbit refueling. Due to the fuel transfer from the...     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

A method for rapidly evaluating reliability and predicting remaining useful life using two-dimensional convolutional neural network with signal conversion

Journal of Mechanical Science and Technology - Real-time monitoring and rapid evaluation of bearing operating conditions, especially for the reliability evaluation and remaining useful life (RUL)...     

Mechanism of smoke suppression by melamine in rigid polyurethane foam

The smoke suppression of rigid polyurethane foam (RPUF) modified by melamine was investigated based on three sections: the condensed phase, the carbon layer, and the gas phase. In the condensed phase, the results of thermogravimetry, X‐ray photoelectron spectroscopy (XPS) N1S spectrum, and Fourier transform infrared spectroscopy indicated that melamine could suppress the degradation of RPUF by reacting with the aromatic hydrocarbons. It also reduced the smoke generation because the volatilizable aromatic hydrocarbons were the principal smoke precursors in a fire. In the carbon layer, the decrease from 38.50% to 24.76% of the inner layer oxygen content identified by XPS full‐spectrum and C1S spectrum indicated that melamine could prevent oxygen from transferring into the inner foam by the formation of an enhanced surface carbon layer, and the enhanced carbon layer could also block the release of smoke precursors. In the gas phase, the content of total aromatic hydrocarbons declined to 59.12% according to pyrolysis gaseous chromatography mass spectroscopy and indicated that melamine could reduce the smoke precursors. The results of smoke density chamber and cone calorimeter tests revealed that the addition of the melamine could decrease the smoke density of burning RPUF. Copyright © 2014 John Wiley & Sons, Ltd.     

聚烯烃催化剂硅胶载体的制备和表征

采用并流共沉淀法制备了适用于聚烯烃催化剂的硅胶载体,为减少颗粒的聚集,在制备过程中添加一种表面活性剂。利用透射电子显微镜(TEM)、比表面积测定(BET)和X射线粉末衍射(XRD)法对制备的硅胶载体进行了表征;考察了在制备硅胶载体过程中原料硅酸钠溶液的浓度、溶液pH以及焙烧温度对产物硅胶载体的物理性能的影响。实验结果表明,硅酸钠溶液的浓度影响硅胶的初始粒子的大小,溶液pH直接影响硅酸钠的水解速率,焙烧温度影响硅胶的孔结构和比表面积。当硅酸钠溶液的浓度为0．2mol／L、溶液pH为8-9、反应温度为70℃、焙烧温度为700℃时,硅胶载体的BET比表面积为242．22m2／g、最可几孔径为16．45 nm、堆密度为0．492 1g/mL,与进口硅胶(Silica Gel 955)的物理性能相近。