Optimal Water Allocation of Surface and Ground Water Resources Under Climate Change with WEAP and IWOA Modeling

Water Resources Management - The water evaluation and planning (WEAP) approach and the invasive weed optimization algorithm (IWOA) are herein employed to determine the optimal operating policies in...     

In Situ ceramic particle-reinforced aluminum matrix composites fabricated by reaction pressing in the TiO2 (Ti)-Al-B (B2O3) systems

Particulate TiB₂ reinforced aluminum-based metal matrix composites (MMCs) were successfully fabricated by means of the reaction processing method. TiB₂ particulates were formed in situ through the reaction of Ti and B in Ti-Al-B, TiO₂ and B in TiO₂-Al-B, and TiO₂ and B₂O₃ in TiO₂-Al-B₂O₃ systems. The results showed that in situ TiB₂ particulates formed in the Ti-Al-B system had a size of 5 μm and they exhibited block and rodlike structures. Moreover, coarse Al₃Ti blocks several tens of micrometers in size were also formed simultaneously. On the other hand, equiaxed Al₂O₃ and TiB₂ particulates with a size of less than 2 μm were formed in situ in the TiO₂-Al-B and TiO₂-Al-B₂O₃ systems. The Al₃Ti phase was completely eliminated in the TiO₂-Al-B system with increasing B content. Tensile tests revealed that the Al₂O₃ · TiB₂/Al composite fabricated from the TiO₂-Al-B system exhibits excellent mechanical properties. The yield strength of the Al₂O₃ · TiB₂/Al composite appeared to increase with increasing TiB₂ content. The yield strength of the Al₂O₃ · TiB₂/Al composite could be further increased by introducing CuO into the TiO₂-Al-B system. Such an increment in mechanical strength arose from the strengthening effect caused by the Al₂Cu precipitates. The incorporation of CuO had no effect on the in situ reaction process of the TiO₂-Al-B system. Finally, the effect of SiC addition on the microstructure and mechanical properties of the composites fabricated from the TiO₂-Al-B and TiO₂-Al-B-CuO systems was also investigated.     

Long-term transients in a reactor under forced concentration cycling

In the approach to a cycle-invariant state in the forced feed concentration cycling of the CO oxidation over a NiO catalyst, a very long transient has been observed lasting 80 ks or more. This transient appears to be associated only with CO pretreatment of the catalyst and is not a general phenomenon. The slow convergence to the cycle-invariant state reported in certain modelling calculations in the literature appears to have a different cause.     

Kinetic model for water/oil absorption of mesquite gum (Prosopis juliflora) and gum arabic (Acacia senegal)

The water and oil uptake of mesquite and arabic gums in powdered form was studied at temperatures of 23, 35 and 45°C. A previously proposed equation to predict osmotic equilibrium was tested using the experimental data with both gums and a good statistical fit was obtained. Mesquite gum showed the highest water and oil absorption at all temperatures studied. Temperature dependence of the reciprocal of the S₁ and WL_∞ were determined using an Arrhenius equation. The activation energy for water and oil absorption for gum arabic was 21.98 and 39.57 kJ mol⁻¹, compared to that of mesquite gum having values of 15.79 and 46.16 kJ mol⁻¹, respectively. A second order kinetic model was obtained for water and oil absorption for both gums.     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

Microstructural and textural characterization of a hot-rolled IF steel

The present paper reports the experimental results on the microstructural and textural characterization of a hot-rolled IF steel. The IF steel was hot-rolled in multiple passes in the austenitic field (1,070 °C) followed by air-cooling. SEM, TEM, and LOM were used to image the microstructure of the material. The global texture was determined by X-ray diffraction (XRD) technique. The mesotexture of selected regions was investigated by electron backscatter diffraction (EBSD). Results show the presence of a diffuse (nearly random) and weak texture in the hot-band that consists of recrystallized polygonal grains and subgrains. The fraction of boundaries with misorientations comprised in the interval 2° ≤ ψ < 15° was found to be lower than 5%. It can be concluded that these low angle boundaries and the presence of subgrains can be associated to the existence of a few areas softened by recovery during or after hot rolling in austenitic field.     

A comparative cerebral blood flow study in a baboon model with acetazolamide provocation: 99mTc-HMPAO vs 123I(IMP)

Pharmacological interactions are important when nuclear medical procedures are applied to patients under drug therapy, or drug provocation. This study compares in baboon models (regional) cerebral blood flow [(r)CBF] results from 99mTc-HMPAO and 123I-iodoamphetamine [123I(IMP)] each with and without acetazolamide, the latter a suggested drug for testing cerebrovascular reserve. Expected differences in cerebral uptake were observed between the two radio-tracers without acetazolamide. The increase in tracer uptake resulting from acetazolamide is significantly enhanced for 123I(IMP), which could have diagnostic implications.