Relationships of tensile strength with crosslink density for the high-carbon black-filled EPDM compounds with various softeners

Equilibrium swelling and rheological tests were adopted to systematically investigate the effects of softener type and dosage on the crosslink densities. The results turned out that the chemical crosslink density could be distinguished from the physical crosslink density by comparing the results of equilibrium swelling and rheological tests. The liquid butadiene (LB) as a softener leads to the greatest reduction in crosslink density, followed by polyethylene wax (PW) and paraffinic oil (PO). The tensile strength decreases with increasing PO content while shows peak values with increase of LB and PW contents. The dependencies of chemical crosslink density on the aging time under 150°C are quite different for the three softeners, which can be expected from the double crosslinking networks consisting of small softener and large main crosslinking networks. Further investigation has been performed to correlate the tensile strength with chemical crosslink density of ethylene propylene diene monomer elastomer vulcanizates. Three different linear relationships can be obtained for the softeners independent of the aging time. It can now be expected from this study that the role of some new softeners in rubber compounds is not only confined to plasticization but also forms crosslinking networks in the peroxide-cured rubbers.     

Core–shell NTC materials with low thermal constant and high resistivity for wide-temperature thermistor ceramics

Core–shell structures have been proposed to improve the electrical properties of negative-temperature coefficient (NTC) thermistor ceramics. In this work, Al₂O₃-modified Co_1.5Mn_1.2Ni_0.3O₄ NTC thermistor ceramics with adjustable electrical properties were prepared through citrate-chelation followed by conventional sintering. Co_1.5Mn_1.2Ni_0.3O₄ powder was coated with a thin Al₂O₃ shell layer to form a core–shell structure. Resistivity (ρ) increased rapidly with increasing thickness of the Al₂O₃ layer, and the thermal constant (B) varied moderately between 3706 and 3846 K. In particular, Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ ceramic with 0.08 wt% Al₂O₃ showed the increase of ρ double, and the change in its B was less than 140 K. The Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics showed high stability, and their grain size was relatively uniform due to the protection offered by the shell. The aging coefficient of the ceramic was less than 0.2% after aging for 500 hours at 125°C. Taken together, the results indicate that as-prepared Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics with a core–shell structure may be promising candidates for application as wide-temperature NTC thermistor ceramics.     

Se doped nickel-molybdenum bimetal sulfide with enhanced electrochemical activity for hydrogen evolution reaction

In this work, we synthesized Se doped MoS₂@Ni₃S₂ with nanosheets coated nanorods structure supported on Ni foam (MoNiSeS). Firstly, MoS₂@Ni₃S₂ (MoNiS) nanorods was synthesized by hydrothermal method. After selenization treatment, MoSe₂ successfully formed on the edge of MoS₂ nanosheets and particle Ni₃S₂ transformed into NiSe, in which MoSe₂ and NiSe acted as new phase in MoNiSeS. The obtained MoNiSeS only needs a low overpotential of 68 mV to reach the current density of 10 mA cm^?2, and has a low Tafel plots of 72.77 mV dec^?1 and good electrochemical durability, whose electrochemical activity is much better than that of MoNiS and NiSeS, implying the introduction of Mo and Se is beneficial to improve the electrocatalytic performance of NiS for HER. In addition, the proper amount of Mo source, which has an effect on the morphology of product, has also been investigated. For MoNiSeS, the typical nanosheets coated nanarods expose more active sites and the synergic effects is good to the improvement of the catalytic activity. Meanwhile, WNiSeS has also been prepared using the same method and the corresponding results show that the electrochemical activity of WNiSeS is much better than that of NiSeS, proving the universality of this strategy.     

吉林台混凝土面板砂砾-堆石坝砂砾排水料特性试验

吉林台一级水电站大坝为混凝土面板砂砾-堆石坝,大坝运用中能及时地排除坝体内的水是大坝安全运行的关键之一。该坝体内设置的排水通道是由料场开采的砂砾料经筛分填筑而成。为掌握该排水料的特性,对其进行了颗粒大小分析,密度、含水率、渗透系数等试验;同时也进行了不同含水情况下的碾压施工参数试验。为该砂砾料在坝工中的应用提供了重要资料,满足了工程要求。     

弹道靶道测量精度检测方法之探讨

该文分析了弹道靶道测量中的精度问题及通常使用的静态检测方法,并针对静态检测与靶道实测相差甚远的问题,提出了一种动态检测方法.该方法充分考虑到弹道靶道的测量对象是高速飞行体以及照片质量、气流附面层、发射时的恶劣环境和振动等因素对测量精度的影响,结合误差理论,给出了动态精度的计算公式,在已建成的IB-12中间弹道靶道中应用,效果良好.     

Coal liquefaction using a hydrogenated creosote oil solvent: H-atom transfer from hydrogen donor components in the solvent

The presence of hydroaromatic, hydrogen donor components in a coal-derived solvent is one of the more important factors in the successful operation of a non-catalytic coal liquefaction process. Various hydrogen donor species present in a hydrogenated creosote oil have been identified. Their rate of disappearance under conditions that are consistent with a short residence time coal liquefaction process has been used to rank the reactivities of the various hydrogen donors. 1,2,3,10b-Tetrahydrofluoranthene was found to be an exceptional donor while 4,5-dihydropyrene, the hexahydropyrenes and 9,10-dihydrophenanthrene were found to be quite active. Sym.-octahydrophenanthrene and 2a,3,4,5-tetrahydroacenaphthene exhibited moderate activity. Tetralin and the four methyltetralin isomers were found to be unreactive under the coal liquefaction conditions employed.     

二滩水电站油、水、风系统设备运行与改造

水电站辅助设备的运行直接影响水电站运行的安全性和可靠性。二滩水电站投运初期，油、水、风系统先后出现了许多问题，通过应用新产品和新技术对其进行了改造。为水电厂辅助设备的设计、选型、安装提供了宝贵的经验，并对水电厂辅助设备的检修、调试和运行维护有一定的指导作用。     

风管摩擦阻力的直接计算方法

提出用高精度的反映密度、黏度和温度关系的经验公式和Colebrook公式计算风管摩擦阻力系数的方法。分析和算例表明，用该方法计算，计算结果比采用常用工程设计方法更为准确，为应用计算机进行风道设计提供了直接、简便的方法。