Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

Photoinduced Formation of Small Gold Particles in Silica Gels

AuCl⁻₄ ions in sol-gel-derived silica gels (Au/silica gels) were photoreduced by ultraviolet light irradiation at room temperature. In the presence of ethylene glycol in the silica gels, small Au particles were effectively formed by the irradiation. When the storage temperature of the gels was increased in the dark after the irradiation, the surface plas-mon resonance absorption peak of the Au particles was shifted to longer wavelengths, indicating that the Au particles became large. At a storage temperature below 9°C, Au particles could not be observed in the silica gels. The apparent activation energy of Au particle formation was estimated to be 17. 3 kcal·tmol⁻¹.     

Driving voltage reduction in a two-phase CCD by suppression ofpotential pockets in inter-electrode gaps

This study reports an optimum design for a two-phase charge-coupled device (CCD) and limitations on its driving voltage reduction. The two-phase CCD to be used as a horizontal-CCD (H-CCD) in a CCD image sensor requires low-voltage and high-speed operation. Reducing the driving voltage, however, may induce potential pockets in the channel under the inter-electrode gaps which results in a fatal decrease in charge-transfer efficiency. In this case it is necessary to optimize the CCD design to be free of pocket generation. For this requirement, we conducted two-dimensional (2-D) device simulations for the two-phase CCD, whose potential barriers are formed by boron ion-implantation. Our simulations indicated that the edge position of the potential barrier region and the dose of boron-ion implantation would be important parameters for controlling the size of potential pockets. At an optimum edge position and a boron dose, the minimum driving voltage appears to be reducible to 1.1 V. Characteristics of potential pockets and methods of their suppression are also discussed     

Analysis of course errors on CVOR antennas (including effects ofmutual coupling between elements)

A VHF omnidirectional radio range (VOR) is a navigation aid radio beacon facility, which provides aircraft with azimuth information relative to the VOR station in question as the origin. In Japan, two types of VOR-the conventional type (referred to as a CVOR) and the Doppler type (referred to as a DVOR)-are currently in use. An element known as the Alford loop antenna (ALA), which changes the loading reactance, is used for the VOR because the horizontally polarized wave and nondirectivity in the horizontal plane are preferred. A VOR antenna consists of a carrier antenna and a sideband antenna-an aircraft receives separate signals from these two antennas and compares them to obtain azimuth information. The mutual coupling between the elements forming the carrier and the sideband antenna affects the directivity of the single elements, resulting in errors in azimuth information. With the mutual coupling between the antenna elements being taken into consideration, a quantitative calculation was made by using the moment method-the results of the calculation made it clear that a loading reactance value of -320 Ω is better to make not mutually coupled elements nondirectional while a loading reactance value of -600 Ω is optimum to minimize the azimuth error of a CVOR     

Scanning electron microscopy of the myosin-coated surface of polystyrene beads in a force-movement assay system for ATP-dependent actin-myosin sliding

An outbreak of Cryptosporidiosis occurred over three months in a British Columbia community, peaking in December 1990. Results of the case-control study and illness surveys support the hypothesis that transmission occurred in a public children's pool at the local recreation centre. Analysis using lab-confirmed cases revealed a matched odds ratio of 4.5 [95% CI 0.97, 20.83], and using clinical cases an unmatched odds ratio of 12.8 [95% CI 3.68, 46.77], associated with swimming in the children's pool within two weeks prior to onset of illness. Other risk factors were not significant. Attack rates in various groups of children's pool users ranged from 8% to 78%. The children's pool was closed for steam cleaning and disinfection. Unusually frequent defecations including liquid stools had occurred before and during the outbreak. Improvements were instituted for removal of feces and superchlorination of pool water.     

2D Image Construction from Low Resolution Response of a New Non‐invasive Measurement for Medical Application

This paper presents an application of digital signal processing to data acquired by the radio imaging method (RIM) that was adopted to measure moisture distribution inside the human body. RIM was originally developed for the mining industry; we are applying the method to a biomedical measurement because of its simplicity, economy, and safety. When a two‐dimensional image was constructed from the measured data, the method provided insufficient resolution because the wavelength of the measurement medium, a weak electromagnetic wave in a VHF band, was longer than human tissues. We built and measured a phantom, a model simulating the human body, consisting of two water tanks representing large internal organs. A digital equalizer was applied to the measured values as a weight function, and images were reconstructed that corresponded to the original shape of the two water tanks. As a result, a two‐dimensional image containing two individual peaks corresponding to the original two small water tanks was constructed. The result suggests the method was applicable to biomedical measurement by the assistance of digital signal processing. This technique may be applicable to home‐based medical care and other situations in which safety, simplicity, and economy are important.