Process Intensification of Living Cationic Polymerization of Isobutylene by a Flow Reaction System

Increasing the reaction temperature of the living cationic polymerization of isobutylene is crucial for industrial production due to the cost of refrigeration. The reaction temperature increase was achieved with an accelerated reaction rate using a flow reaction system. The polymerization conditions, including the flow reactor design, were based on the results of kinetic studies. Utilizing a milli‐scale flow reactor, polyisobutylene, which has a narrow molecular weight distribution, was obtained within a considerably short residence time at a high temperature. Furthermore, it was confirmed that the value of M_w/M_n correlates with the product of the Reynolds number and the angle of collision.     

A single-chip digitally calibrated 5.15-5.825-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a wireless LAN

The drive for cost reduction has led to the use of CMOS technology in the implementation of highly integrated radios. This paper presents a single-chip 5-GHz fully integrated direct conversion transceiver for IEEE 802.11a WLAN systems, manufactured in 0.18-/spl mu/m CMOS. The IC features an innovative system architecture which takes advantage of the computing resources of the digital companion chip in order to eliminate I/Q mismatch and achieve accurately matched baseband filters. The integrated voltage-controlled oscillator and synthesizer achieve an integrated phase noise of less than 0.8/spl deg/ rms. The receiver has an overall noise figure of 5.2 dB and achieves sensitivity of -75 dBm at 54-Mb/s operation, both referred to the IC input. The transmit error vector magnitude is -33 dB at -5-dBm output power from the integrated power-amplifier driver amplifier. The transceiver occupies an area of 18.5 mm/sup 2/.     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

Very low threshold graded-indexseparate-confinement-heterostructure strained InGaAsPsingle-quantum-well lasers

A low threshold current density of ~100 A/cm² has been obtained at 1.55 μm using a graded-index separate-confinement-heterostructure strained InGaAsP single-quantum-well laser. The design of the laser structure is based on results calculated from the viewpoint of effective carrier injection into the well     

Photoinduced Formation of Small Gold Particles in Silica Gels

AuCl⁻₄ ions in sol-gel-derived silica gels (Au/silica gels) were photoreduced by ultraviolet light irradiation at room temperature. In the presence of ethylene glycol in the silica gels, small Au particles were effectively formed by the irradiation. When the storage temperature of the gels was increased in the dark after the irradiation, the surface plas-mon resonance absorption peak of the Au particles was shifted to longer wavelengths, indicating that the Au particles became large. At a storage temperature below 9°C, Au particles could not be observed in the silica gels. The apparent activation energy of Au particle formation was estimated to be 17. 3 kcal·tmol⁻¹.     

640-Gb/s high-speed ATM switching system based on 0.25-μm CMOS,MCM-C, and optical WDM interconnection

A 640-Gb/s high-speed ATM switching system that is based on the technologies of advanced MCM-C, 0.25-μm CMOS, and optical wavelength-division-multiplexing (WDM) interconnection is fabricated for future broadband backbone networks. A 40-layer, 160×114 mm ceramic MCM forms the basic ATM switch module with 80-Gb/s throughput. It consists of 8 advanced 0.25-μm CMOS LSIs and 32 I/O bipolar LSIs. The MCM has a 7-layer high-speed signal line structure having 50-Ω strip lines, high-speed signal lines, and 33 power supply layers formed using 50-μm thick ceramic layers to achieve high capacity. A uniquely structured closed-loop-type liquid cooling system for the MCM is used to cope with its high power dissipation of 230 W. A three-stage ATM switch is made using the optical WDM interconnection between high-performance MCMs. For WDM interconnection, newly developed compact 10-Gb/s, 8-WDM optical transmitter and receiver modules are used. These modules are each only 80×120×20 mm and dissipate 9.65 W and 22.5 W, respectively. They have a special chassis for cooling, which contains high-performance heat-conductive plates and micro-fans. An optical WDM router based on an arrayed waveguide router is used for mesh interconnection of boards. The optical WDM interconnect has 640-Gb/s throughput and simple interconnection     

Application of gene gun for local-regional cancer

We studied the in vivo gene transfusion using a gene gun, formerly used in plants and culture cells. The hand-held type gene gun (Helios Gene Gun System) is simple and convenient for effective gene transfection in living animals. This method has some advantages in that there is no need for use of viral vector, independence on the cell cycle and local inducement of plural genes. There is a great possibility for application to local-regional cancer.     

2D Image Construction from Low Resolution Response of a New Non‐invasive Measurement for Medical Application

This paper presents an application of digital signal processing to data acquired by the radio imaging method (RIM) that was adopted to measure moisture distribution inside the human body. RIM was originally developed for the mining industry; we are applying the method to a biomedical measurement because of its simplicity, economy, and safety. When a two‐dimensional image was constructed from the measured data, the method provided insufficient resolution because the wavelength of the measurement medium, a weak electromagnetic wave in a VHF band, was longer than human tissues. We built and measured a phantom, a model simulating the human body, consisting of two water tanks representing large internal organs. A digital equalizer was applied to the measured values as a weight function, and images were reconstructed that corresponded to the original shape of the two water tanks. As a result, a two‐dimensional image containing two individual peaks corresponding to the original two small water tanks was constructed. The result suggests the method was applicable to biomedical measurement by the assistance of digital signal processing. This technique may be applicable to home‐based medical care and other situations in which safety, simplicity, and economy are important.