Advanced Characterization and Optimization of NiOx:Cu-SAM Hole-Transporting Bi-Layer for 23.4% Efficient Monolithic Cu(In,Ga)Se2-Perovskite Tandem Solar Cells

The performance of five hole-transporting layers (HTLs) is investigated in both single-junction perovskite and Cu(In, Ga)Se₂ (CIGSe)-perovskite tandem solar cells: nickel oxide (NiO_x,), copper-doped nickel oxide (NiO_x:Cu), NiO_x+SAM, NiO_x:Cu+SAM, and SAM, where SAM is the [2-(3,-6Dimethoxy-9H-carbazol-9yl)ethyl]phosphonic acid (MeO-2PACz) self-assembled monolayer. The performance of the devices is correlated to the charge-carrier dynamics at the HTL/perovskite interface and the limiting factors of these HTLs are analyzed by performing time-resolved and absolute photoluminescence ((Tr)PL), transient surface photovoltage (tr-SPV), and X-ray/UV photoemission spectroscopy (XPS/UPS) measurements on indium tin oxide (ITO)/HTL/perovskite and CIGSe/HTL/perovskite stacks. A high quasi-Fermi level splitting to open-circuit (QFLS-V_oc) deficit is detected for the NiO_x-based devices, attributed to electron trapping and poor hole extraction at the NiO_x-perovskite interface and a low carrier effective lifetime in the bulk of the perovskite. Simultaneously, doping the NiO_x with 2% Cu and passivating its surface with MeO-2PACz suppresses the electron trapping, enhances the holes extraction, reduces the non-radiative interfacial recombination, and improves the band alignment. Due to this superior interfacial charge-carrier dynamics, NiO_x:Cu+SAM is found to be the most suitable HTL for the monolithic CIGSe-perovskite tandem devices, enabling a power-conversion efficiency (PCE) of 23.4%, V_oc of 1.72V, and a fill factor (FF) of 71%, while the remaining four HTLs suffer from prominent V_oc and FF losses.     

Key Performance Indicators for Strategic Healthcare Facilities Maintenance

The salient phases in a facility’s service life that are most decisive for the effectiveness of its facilities management (FM) are the preliminary design, construction, and maintenance. The effectiveness of facilities is vastly affected by decisions pertaining to the strategy of the organization that owns or uses the facilities. The goal of this study was to develop key performance indicators (KPIs) for strategic FM that will provide a conclusive approach towards the facility’s service life conditions. Parameters were developed by means of field surveys and statistical analyses, and were validated by means of case studies. The research resulted in a series of 11 KPIs for strategic healthcare FM, which can be classified into four categories: development, organization and management, performance, and maintenance efficiency parameters. The study proposes age and occupancy coefficients as essential parameters for the assessment of large healthcare facilities needs, as an effective measure for long term facility maintenance planning, and for measuring FM effectiveness. The paper stresses that strategic healthcare facilities management must integrate quantitative performance, manpower, and maintenance indicators.     

Photodegradation of sulphadimethoxine in water by medium pressure UV lamp

The photodegradation rate of sulphadimethoxine (SMT) in water was studied under polychromatic UV light, in a bench scale apparatus. SMT photolysis was carried out at pH levels of 2.5, 6.5 and 10 to study the impact of acid base properties on the degradation of SMT. The highest SMT photolysis fluence based rate was found at pH=2.5 (k=7.22x10(-4) cm2/mJ) and the lowest rate at pH=10 (k=4.72x10(-4) cm2/mJ), thus the reaction rate decreases with an increase in pH between pH values of 2.5-10. Results indicated that direct photolysis is not satisfactory for degradation of SMT by polychromatic UV lamp as a fluence of approximately 7,000 mJ/cm2 is needed to break down 99% of SMT at pH 6.5. The photodegradation products of SMT were studied at various pH values. Photodegradation of SMT results in dissimilar relative amounts of intermediates formed at different pH values which may exert a photon demand and impact on SMT photodegradation rate.     

Relative importance of informational units and their role in long-term recall by closed-head-injured patients and control groups.

Applied qualitative analysis to the information recalled by control Ss and closed-head-injured (CHI) patients. The Logical Memory subtest of the Wechsler Memory Scale (WMS) was administered to 40 CHI and 40 control Ss. Recall was tested immediately after administration, 40 min later, and 24 hrs later. The analysis took into account the importance of recalled information as determined by a prior rating according to 3 levels of importance. Results suggest that CHI patients have difficulty selectively retrieving the most important information after a long delay. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Changes in chemical constituents during the maturation and ripening of two commercially important pomegranate accessions

Pomegranate juice is well known for its health beneficial compounds. This study was undertaken to investigate changes in the major chemical composition in arils and peels during fruit maturation in two Israeli commercial accessions, ‘Wonderful’ and ‘Rosh-Hapered.’ In both accessions, the levels of total phenolic, antioxidant activity and hydrolysable tannins were reduced in the peels during maturation, while the anthocyanin level increased. The results show that the sugar content in the aril juice increased in both accessions while the levels of acidity and of citric acid decreased. However, these two accessions differed in other parameters in the aril juice, i.e., while the antioxidant and total phenolic contents significantly decreased in ‘Rosh-Hapered’, these changes were not observed in ‘Wonderful’. The anthocyanin level, however, increased in ‘Wonderful’ but did not change in ‘Rosh-Hapered.’ This knowledge could help establish the optimum harvest date ensuring the maximum nutritional properties of pomegranates.     

Role of zirconium in the phase formation at the interdendritic zone in nickel-based superalloys

A commercial Alloy 80A and a modified alloy with lower titanium and zirconium contents, e.g. 1.4% and <0.01%, respectively, were subjected to unidirectional solidification followed by a rapid quench in water to preserve the structure at elevated temperatures. The slow solidification results in a coarse dendritic structure with a high enrichment of sulphur (up to 2%), aluminium (up to 4%), titanium (up to 13%) and zirconium in the interdendritic zones. In the commercial Alloy 80A, the zirconium and sulphur present in the interdendritic zone result in a eutectic containing ZrS and NiCrTi-matrix. Excess zirconium forms an NiZr-intermetallic. No TiS is formed in this case. In the absence of zirconium, the titanium enriched in the interdendritic residual melt forms a eutectic of TiS. In both cases the effective solidus temperature corresponding to the composition of the residual melt is 1170°C, compared to 1330 °C, which is the solidus temperature of the bulk material.     

Pure CuBi2O4 Photoelectrodes with Increased Stability by Rapid Thermal Processing of Bi2O3/CuO Grown by Pulsed Laser Deposition

A new method for enhancing the charge separation and photo‐electrochemical stability of CuBi₂O₄ photoelectrodes by sequentially depositing Bi₂O₃ and CuO layers on fluorine‐doped tin oxide substrates with pulsed laser deposition (PLD), followed by rapid thermal processing (RTP), resulting in phase‐pure, highly crystalline films after 10 min at 650 °C, is reported. Conventional furnace annealing of similar films for 72 h at 500 °C do not result in phase‐pure CuBi₂O₄. The combined PLD and RTP approach allow excellent control of the Bi:Cu stoichiometry and results in photoelectrodes with superior electronic properties compared to photoelectrodes fabricated through spray pyrolysis. The low photocurrents of the CuBi₂O₄ photocathodes fabricated through PLD/RTP in this study are primarily attributed to their low specific surface area, lack of CuO impurities, and limited, slow charge transport in the undoped films. Bare (without protection layers) CuBi₂O₄ photoelectrodes made with PLD/RTP shows a photocurrent decrease of only 26% after 5 h, which represents the highest stability reported to date for this material. The PLD/RTP fabrication approach offers new possibilities of fabricating complex metal oxides photoelectrodes with a high degree of crystallinity and good electronic properties at higher temperatures than the thermal stability of glass‐based transparent conductive substrates would allow.     

Design methodology of refractive index engineering by implantation of high-energy particles in electro-optic materials

Slab waveguides were constructed in K(1-x)Li(x)Ta(1-y)Nb(y)O(3) crystals by the implantation of (12)C(+4) ions at 30 MeV and (16)O(+5) ions at 30 and 40 MeV. The waveguides were characterized by a prism coupler setup. A refractive index drop of 10.9% was observed in a layer formed by the implantation of (16)O(+5) ions at 30 MeV. The carbon-implanted waveguides were found to be thermally stable after annealing at 450 degrees C. A semiempirical formula for predicting the change in the refractive index given the parameters of the implantation process was developed. It is argued that the combination of the basic implantation process with the semiempirical formula can be developed to become a generic method for constructing complex electro-optic circuits with a wave-guided architecture.