Driving voltage reduction in a two-phase CCD by suppression ofpotential pockets in inter-electrode gaps

This study reports an optimum design for a two-phase charge-coupled device (CCD) and limitations on its driving voltage reduction. The two-phase CCD to be used as a horizontal-CCD (H-CCD) in a CCD image sensor requires low-voltage and high-speed operation. Reducing the driving voltage, however, may induce potential pockets in the channel under the inter-electrode gaps which results in a fatal decrease in charge-transfer efficiency. In this case it is necessary to optimize the CCD design to be free of pocket generation. For this requirement, we conducted two-dimensional (2-D) device simulations for the two-phase CCD, whose potential barriers are formed by boron ion-implantation. Our simulations indicated that the edge position of the potential barrier region and the dose of boron-ion implantation would be important parameters for controlling the size of potential pockets. At an optimum edge position and a boron dose, the minimum driving voltage appears to be reducible to 1.1 V. Characteristics of potential pockets and methods of their suppression are also discussed     

Analysis of course errors on CVOR antennas (including effects ofmutual coupling between elements)

A VHF omnidirectional radio range (VOR) is a navigation aid radio beacon facility, which provides aircraft with azimuth information relative to the VOR station in question as the origin. In Japan, two types of VOR-the conventional type (referred to as a CVOR) and the Doppler type (referred to as a DVOR)-are currently in use. An element known as the Alford loop antenna (ALA), which changes the loading reactance, is used for the VOR because the horizontally polarized wave and nondirectivity in the horizontal plane are preferred. A VOR antenna consists of a carrier antenna and a sideband antenna-an aircraft receives separate signals from these two antennas and compares them to obtain azimuth information. The mutual coupling between the elements forming the carrier and the sideband antenna affects the directivity of the single elements, resulting in errors in azimuth information. With the mutual coupling between the antenna elements being taken into consideration, a quantitative calculation was made by using the moment method-the results of the calculation made it clear that a loading reactance value of -320 Ω is better to make not mutually coupled elements nondirectional while a loading reactance value of -600 Ω is optimum to minimize the azimuth error of a CVOR     

Scanning electron microscopy of the myosin-coated surface of polystyrene beads in a force-movement assay system for ATP-dependent actin-myosin sliding

An outbreak of Cryptosporidiosis occurred over three months in a British Columbia community, peaking in December 1990. Results of the case-control study and illness surveys support the hypothesis that transmission occurred in a public children's pool at the local recreation centre. Analysis using lab-confirmed cases revealed a matched odds ratio of 4.5 [95% CI 0.97, 20.83], and using clinical cases an unmatched odds ratio of 12.8 [95% CI 3.68, 46.77], associated with swimming in the children's pool within two weeks prior to onset of illness. Other risk factors were not significant. Attack rates in various groups of children's pool users ranged from 8% to 78%. The children's pool was closed for steam cleaning and disinfection. Unusually frequent defecations including liquid stools had occurred before and during the outbreak. Improvements were instituted for removal of feces and superchlorination of pool water.     

Effect of chromium content on remarkably rapid nitriding in austenitic Fe-Ni-Cr alloys

Remarkably rapid nitriding which is independent of diffusion theory based on the thermal activation process, was observed during nitriding of austenitic Fe-Ni-Cr steels containing 16 and 19 mass% chromium. Increase of the chromium content in the alloys yielded increasing thickness of the nitrided layer, i.e. the internal nitriding theory did not hold in the nitriding. No rapid nitriding was observed in steels containing less than 13 mass% chromium. Hence the limiting concentration of chromium for the rapid nitriding will lie between 13 and 16 mass% chromium. A solution to the problem of abnormalities arising during nitriding of practical austenitic stainless steels which have been investigated since 1972, has been presented experimentally by nitriding various chromium-containing steels. Based on the experimental results, the origin of the rapid nitriding is discussed in connection with the free-energy function of Cr₂N and CrN to temperature. In particular, a plateau of nitrogen concentration measured in the nitrided layers leads to the conclusion that a forced nitrogen diffusion in the layer resulted in the rapid nitriding.     

Schottky barrier heights of contact metals to p-type ZnSe

Schottky barrier heights (SBHs) of a variety of metals (In, Cd, Nb, Ti, W, Cu, Ag, Au, Ni, Pt, and Se) contacting to p-ZnSe grown by a molecular beam epitaxy method were determined by analyzing capacitance-voltage (C-V) and/or current density-voltage (J-V) curves. The SBH values of the Au and Ni contacts were determined from intersections of straight lines of the C⁻²-V curves to be 1.23 and 1.13 eV, respectively. The J-V calculations provided a large SBH value of 1.2 ± 0.1 eV for a variety of metals, indicating that the Fermi-level could be pinned at the contact interface. Reduction of the SBH values to a level lower than 0.4 eV and/or increase of doping concentrations to a level higher than 10²⁰ cm⁻³ are essential to obtain an ohmic contact with contact resistivity of around 10⁻³ Ω·cm².     

Surface characterization and catalytic properties of La1−x -Sr x CoO3

The surface chemical states of the perovskite-type compounds, strontium doped lanthanum cobalt oxides (La_1?x Sr _x CoO₃), have been investigated using X-ray photoelectron spectroscopy (XPS). Catalytic oxidations of both methane and CO have also been investigated using flow methods. The chemical composition of the surface of La_1?x Sr _x CoO₃ was very different from that in the bulk, which was measured by X-ray fluorescence spectroscopy (XRFS). The catalytic activity of La_1?x Sr _x CoO₃ increased with an increase in the quantity of cobalt atoms on the surface.