Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Improved quantum efficiency of Sr(Al,Si)5(O,N)7:Ce3+ by selection of Ce raw material

The luminescence properties of yellow-emitting Ce³⁺-doped Sr-containing sialon phosphor Sr(Al,Si)₅(O,N)₇:Ce³⁺ were notably improved by the Ce raw material selection. By changing the Ce raw material from oxides to nitrides or chlorides, the emission wavelength shifted to above 560 nm, which is beneficial for higher color rendering index white light-emitting diodes. This result from an increase in the covalency of the host crystal being associated with a decrease in the oxygen content. When Ce chloride was used, both the absorption and internal quantum efficiency increased, resulting in an increase in the external quantum efficiency up to 65%–72%. Inductively coupled plasma mass spectrometry, X-ray diffraction, and electron spin resonance measurements showed that the reason for the absorption increase is an increase in Ce³⁺ content and suppression of the generation of the second phase, and the reason for the increase in the internal quantum efficiency is a decrease in the host crystal absorption via suppression of anion vacancy generation. It was found that Ce chloride not only suppresses oxygen impurities but also acts as a flux that results in improved crystallinity.     

Effects of vasodilators and perfusion pressure on coronary flow and simultaneous release of nitric oxide from guinea pig isolated hearts

OBJECTIVE: The aims were to validate the use of a direct reading NO electrode, to compare the effects of diverse acting drugs on altering coronary flow (CF) and NO release, and to examine the effects of altered perfusion pressure on flow-induced changes in NO concentration [NO] in the hemoglobin free effluent of guinea pig isolated hearts. METHODS: Hearts were isolated and perfused initially at a constant perfusion pressure (55 mmHg) with a modified Krebs-Ringer's solution equilibrated with 97% O2 and 3% CO2 at 37 degrees C. Heart rate, left ventricular pressure, CF, and effluent pH, pCO2, pO2, and NO generated current were monitored continuously on-line. Effluent was sampled for L-citrulline. Percent O2 extraction and O2 consumption were calculated. [NO] was quantitated with a sensitive amperometric sensor (sensitivity > or = 1 nmol/l approximately 3 pA) and a selective gas permeable membrane. RESULTS: The electrode was not sensitive to changes in solution pO2, flow, or pressure. The electrode was sensitive to pCO2 (-0.50 nmol/l/mmHg) and temperature (+24.5 nmol/l/degree C), so coronary effluent pCO2 was measured to compensate for a small decrease in pCO2 that occurred with an increase in coronary flow, and effluent temperature was rigidly controlled. Serotonin, bradykinin, and nitroprusside increased NO release along with CF, whereas nifedipine, butanedione monoxime, zaprinast, and bimakalim comparably increased CF but did not increase [NO] or NO release. Increases in CF (ml/g/min) and NO release (pmol/g/min), respectively, were 5.0 +/- 1 and 100 +/- 17 for 1 mumol/l serotonin, 7.5 +/- 1 and 148 +/- 18 for 100 nmol/l bradykinin, and 7.8 +/- 1 and 173 +/- 28 for 100 mumol/l nitroprusside. The increases in effluent NO by bradykinin were proportional to the increases in L-citrulline. Tetraethylammonium decreased CF, but did not change NO release, indomethacin changed neither CF nor NO release, and NG-nitro-L-arginine methyl ester (L-NAME) reduced CF by 2.6 +/- 1 ml/g/min and NO release by 25 +/- 8 pmol/g/min. An increase of CF of 8.0 +/- 0.3 ml/g/min, produced by increasing perfusion pressure from 25 to 90 mmHg, increased [NO] by 30 +/- 4 nmol/l; L-NAME but did not reduce the pressure-induced increase in CF, but reduced the increase in [NO] to 10 +/- 5 nmol/l. CONCLUSIONS: This study demonstrates in intact hearts real-time release of NO by several vasodilator drugs and by pressure-induced increases in flow (shear stress) and attenuation of these effects by L-NAME.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

Effectiveness of spatial representation in the formation of network communities: experimental study on community organizer

In this paper, we present and discuss Community Organizer, a system designed to support network communities. The main characteristic of Community Organizer is the use of spatial representations for the relationships among community members including the communications exchanged among these members. These spatial representations reflect the degree of closeness of interests and concerns among the members, and are intended to provide users with clues on how to form network communities. In order to investigate the effectiveness of the proposed spatial representations, we conducted experiments with two different versions of the software. One version offered meaningful spatial representations while the other version did not. The subjects who used the former software version felt a greater sense of ‘community’, enjoyed using the software more, and actively used it longer than the subjects using the latter software version (control condition). These results indicated that the proposed spatial representations are effective in supporting network community formation.