Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Strength of Al-Zn-Mg-Cu matrix composite reinforced with SiC particles

The AA7075 alloys reinforced with SiC and without SiC particles were fabricated by a pressureless infiltration method, and then, their tensile properties and microstructures were analyzed. The spontaneous infiltration of molten metal at 800 °C for 1 hour under a nitrogen atmosphere made it possible to fabricate 7075 Al matrix composite reinforced with SiC, as well as a control 7075 Al without SiC. A significant strengthening even in the control alloy occurred due to the formation of in-situ AlN particle even without an addition of SiC particles. Composite reinforced with SiC particles exhibited higher strength values than the control alloy in all aging conditions (underaged (UA), peak-aged (PA), and overaged (OA)), as well as a solution treated condition. Spontaneous infiltration was further prompted owing to the combined effect of both Mg and Zn. This may lead to an enhancement of wetting between the molten alloy and the reinforcement. Consequently, strength improvement in a composite may be attributed to good bond strength via enhancement of wetting. The grain size of the control alloy is greatly decreased to about 2.5 μm compared to 10 μm for the commercial alloy. In addition, the grain size in the composite is further decreased to about 2 μm. These grain refinements contributed to strengthening of the control alloy and the composite.     

Formation of C4 species in the deactivation of a Pd/SiO2 catalyst during the selective hydrogenation of acetylene

The deactivation characteristics of Pd/SiO₂ in the selective hydrogenation of acetylene were correlated with changes in the amount of the C4 species produced. The amounts of butenes produced changed in parallel with the catalyst activity, indicating that the rate limiting step for butene production was the same as that for acetylene hydrogenation. On the other hand, the amount of 1,3-butadiene produced changed, showing a maximum with catalyst deactivation because 1,3-butadiene is an intermediate in the sequential reaction process which involves both the production and consumption of 1,3-butadiene. This was verified by a simultaneous TG/reaction experiment showing that 1,3-butadiene was a precursor of green oil. The catalyst showed a self-regenerative behavior in its activity and the amounts of C4 species produced during the early stage of deactivation because two opposite factors, which contributed to either the lowering or the promotion of activity, were involved in the process. A specific type of polymer species, produced during the initial period of deactivation, is proposed to be responsible for the promotion of catalyst activity.     

Adaptive contour smoothing based on inter-region contrast

An adaptive contour smoothing algorithm designed as a preprocessor for shape coders is presented. In the method, the degree of the adaptive smoothing is controlled based on the significance of each contour point, which is quantified according to inter-region contrast in an intensity image. The actual smoothing consists of an expansion operator and a thinning algorithm.     

Hydride Vapor Phase Epitaxy of GaN Thick Films by the Consecutive Deposition Process Using GaCl3

GaN buffer and main layers were grown by the conventional hydride vapor phase epitaxy technique using GaCl₃ consecutively. The deposited buffer layers were investigated by atomic force microscopy and X-ray analysis. To examine the behavior of the buffer layers at main layer growth temperature, heat treatment was conducted at 900°C. Based on the results of the buffer layer study, GaN thick films were grown at 1050°C. Optimum deposition conditions of buffer layer from the buffer and main layer studies generally coincided. On the φ scanning pattern, the GaN films grown on (0001) Al₂O₃ were single-crystalline. Band-edge emission dominated photoluminescence was observed at room temperature.     

An efficient assumed strain element model with six DOF per node for geometrically non-linear shells

The present paper describes an assumed strain finite element model with six degrees of freedom per node designed for geometrically non-linear shell analysis. An important feature of the present paper is the discussion on the spurious kinematic modes and the assumed strain field in the geometrically non-linear setting. The kinematics of deformation is described by using vector components in contrast to the conventional formulation which requires the use of trigonometric functions of rotational angles. Accordingly, converged solutions can be obtained for load or displacement increments that are much larger than possible with the conventional formulation with rotational angles. In addition, a detailed study of the spurious kinematic modes and the choice of assumed strain field reveals that the same assumed strain field can be used for both geometrically linear and non-linear cases to alleviate element locking while maintaining kinematic stability. It is strongly recommended that the element models, described in the present paper, be used instead of the conventional shell element models that employ rotational angles.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.