Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

Anthocyanin composition of the red wine Babić affected by maceration treatment

Identification of anthocyanins in the wine made of the Croatian autochthonous grape variety of Babić (Vitis vinifera L.) was carried out and their profile was determined by means of high-performance liquid chromatography with diode array and mass spectrometric detection. Dependence of anthocyanins content and profile on maceration treatment conditions was investigated. Statistically significant differences of anthocyanins concentration in wines Babić produced by various maceration treatments were confirmed by the use of multivariate analysis of variances. The investigation results indicated that the maceration temperature exerts higher influence on anthocyanins concentration than the duration of maceration. In addition, on the basis of anthocyanin composition and using different multivariate statistical analyses, differentiation of wines Babić according to maceration treatments was procured.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Low temperature and strain rate dependence of fracture stress and fracture toughness on thin Fe40Ni40B20 amorphous ribbon

The fracture stress and the critical stress intensity factor of the Fe₄₀Ni₄₀B₂₀ amorphous metallic ribbons 20 μm thick were measured in the temperature range 4.2–300 K and at deformation rates from 3.3×10⁻⁶ to 1.25×10⁻³ m⁻¹ with the aim to obtain more information on the condition for the onset and development of the inhomogeneous plastic deformation and fracture.     

The influence of preparation conditions on the electrochemical behaviour of CuO in a Li/CuO cell

A dozen CuO samples prepared under various conditions and from different starting materials were evaluated as cathode materials for a primary Li/CuO cell. The “thin electrode” method was used for rapid evaluation of the samples. Both coulombic efficiency and discharge voltage depend considerably on the method of synthesis. No correlation was found between the specific surface area and the resistivity of the samples on the one hand and the cathode performance on the other. Best results were obtained from CuO prepared by the oxidation of Cu₂O under controlled temperature and time of oxidation.     

Application of substituted N-arylpyrroles in the corrosion protection of aluminium in hydrochloric acid

The inhibiting action of N-arylpyrroles on aluminium in 0.17 mol dm^–3 hydrochloric acid solution, in the temperature range 20–60 °C, was studied using potentiodynamic and electrochemical impedence spectroscopy techniques. The inhibiting efficiency of both investigated compounds 1-(2-fluorophenyl)-2,5-dimethylpyrrole (compound A) and 1-(2-fluorophenyl)-2,5-dimethylpyrrole-3-carbaldehyde (compound B) slightly increases with increasing temperature of the corrosive solution. Inhibitor adsorption on the elecrode surface decreases the apparent activation energy of the hydrogen evolution reaction. Compound A follows the Temkin adsorption isotherm, while its carbaldehyde derivative follows the Langmuir isotherm. The results of the apparent energy of activation and the standard free energy of adsorption point to stronger chemisorption of the compound A. However, due to additional condensation of molecules with carbaldehyde groups on the electrode surface, the carbaldehyde derivative exhibits even better inhibiting efficiency than compound A. The kinetic corrosion parameters, analysed in terms of the impedance data, show a satisfactory agreement with those obtained by the potentiodynamic method.     

Reactive energy measurement using frequency controlled analog-to-pulse-rate converter

Contents This paper analyzes a problem of phase shifting and deseribes a novel method for electronic reactive energy measurement. The proposed measurement structure, composed of an integrator as a phase shifting circuit and a frequency controlled analog-to-pulse-rate converter, provides for the measurement completely in accordance with IEC definition of reactive energy, which is performed with simple but high performance metering device.

---

Die Blindverbrauchsmessung anhand eines netzsynchronisierten Analog-Frequenz-Wandlers

Übersicht In diesem Artikel wird das Problem der Phasenverschiebung analysiert und eine neue Meßmethode für elektronische Blindverbrauschsmessung aufgezeigt. Die vorgeschlagene Strucktur, bestehend aus einem Integrator als Phasenschieber und netzkontrolliertem Analog-Frequenz-Wandler, ermöglicht die Verwirklichung eines einfachen aber präzisen Elektrizitätszählers zur Messung der Blindenergie, dessen Arbeitsprinzip mit den IEC Empfehlungen vollkommen übereinstimmt.