Generation of gas bubbles in microflow using micropipette with ultrasound

Ultrasound was applied to a micropipette micromixer to improve dispersion of gas and liquid in a microchannel. Flow visualization using a high-speed camera was performed to examine the effect of ultrasonic irradiation on bubble generation in the microchannel. Basically, nitrogen gas was injected using a (0.5 µm ID) glass micropipette into ethanol flowing in a rectangular (100 µm×200 µm) microchannel on polydimethylsiloxane (PDMS). Gas and liquid flow rates were regulated using mass flow controllers. At aflow condition that is typical of bubbly flow, ultrasound was transmitted into the microchannel using a piezo-electric (PZT) transducer over a range of operating voltages (2 to 200 Vp-p) and frequencies (50 to 60 kHz). Images captured during the action of the PZT transducer indicate that bubble formation is influenced by ultrasound. When subjected to ultrasound above 50 Vp-p and at the resonant frequency of the PZT transducer, bubbles formed that were smaller and closer together, signifying enhanced shearing of the gas at the micropipette tip by the liquid. The observation of gas slugs occurring sooner might be attributed to the coalescence of gas bubbles that became closely spaced.     

Synthesis and surface properties of novel fluoroalkyl end-capped amphiphilic fullerene cooligomers

New fluoroalkyl end-capped fullerene cooligomers were prepared by the reactions of fluoroalkanoyl peroxides with fullerene and comonomers such as acryloylmorpholine, N,N-dimethylacrylamide and acrylic acid. These fluorinated fullerene cooligomers were easily soluble in water and common organic solvents, and were able to reduce the surface tensions of both water and benzene, quite effectively. Additionally, these fullerene cooligomers were found to form a stable monomolecular film at the air-water interface, and the modified polystyrene surface treated with these cooligomers was shown to have a strong hydrophilicity with good oil repellency.     

S06 桂花幻想之月夜——梦天

作为厦门园博会风景园林师园之一,本园以"梦天"为主题,结合东端开阔的水面条件,以月、桂、石为材,以天气的变化、月亮的位置、植物的变化、庭园本身的变化为主轴进行设计,使其成为一座可持续的庭园.     

High-performance carbon counter electrode for dye-sensitized solar cells

Here, we reported that a new carbon electrode prepared with an activated carbon was superior to a Pt sputtered electrode as the counter electrode of dye-sensitized solar cells. The photovoltaic performance was largely influenced by the roughness factor of carbon electrode. The open-circuit voltage increased by about 60 mV using the carbon counter electrode compared to the Pt counter electrode because of positive shift of the formal potential for I₃⁻/I⁻ couple.     

Effects of vitamin B6 deficiency on cytokine levels and lymphocytes in mice

The effects of vitamin B6 (B6) deficiency on cytokine levels and proportions of lymphocyte subsets in BALB/c mice were investigated. The proportion of lymphocytes from the thymus and spleen of mice given no B6, that were CD4+ CD8- T cells, was larger than in mice given B6, and the ratio of CD8+ to CD4+ T cells in the thymus of mice given no B6 was lower. The concentrations of interleukin-5 and -10 in spleen cells stimulated in vitro with concanavalin A were significantly higher in the mice with B6 deficiency, as was their plasma corticosterone concentrations. These results suggested that B6 is necessary to maintain cytokine levels and lymphoid function in the thymus and spleen of mice.     

Automatic optical inspection of plated through-holes for ultrahigh density printed wiring boards

An automatic optical through-hole inspection system for ultrahigh density printed wiring boards (PWBs) using leakage light detection has been developed. To detect the dim leakage light emitted from the through-hole defect, we enhanced the sensitivity of the light detector 150 times using a microchannel plate tube. However, the tube caused two problems: stray light sensing and image distortion. To solve these problems, we optically isolated the sensing optics and developed a distortion correction method. We have developed a prototype system that can detect a defect as small as 100 m.     

Co-crosslinking blend of incompatible polymers VI: Poly(vinyl chloride) toughened with polyethylene via a co-crosslinking technique

A binary blend which consists of two incompatible polymers such as poly(vinyl chloride) and polyethylene has been performed through a partial co-crosslinking reaction with peroxide to give a co-crosslinked blend with a uniform dispersion of small polyethylene particles and with an improved mechanical property. The results are obtained through the formation of a co-crosslinked product which acts as a potential solid phase dispersant as well as a well-bonded reinforcing interlayer on polyethylene particles uniformly dispersed in poly(vinyl chloride) matrix. The resulting blends (PVC/PE=10/90 wt) give carbon spherules of 0.5 to 1m diameter through pressure-carbonization at 650° C for 1 h.     

Surface modification of tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) by plasmas for copper metallization

Tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) sheet surfaces were modified with argon, helium, oxygen, and hydrogen plasmas. How the four plasmas modified the PFA sheet surfaces was investigated. All plasmas modified the PFA surfaces and at the same time initiated degradation of the PFA polymer chains. The balance between modification and degradation was strongly influenced by the magnitude of the discharge current in the plasmas. Efficiency of the plasmas in modification was hydrogen plasma > oxygen plasma > argon plasma > helium plasma. The modification involved defluorination of CF₂ carbons into CHF and CH₂ carbons and oxidation into O? CH₂, O? CHF, and O? CF₂ groups. The surface‐modification technique (a combination of hydrogen plasma treatment and silane coupling treatment) proposed in this study was applied for copper metallization of the PFA surface. The utility of the technique was confirmed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1087–1097, 2002     

Microstructure of carbon spherules

Carbon spherules were formed from a mixture of polyethylene with 5–10 wt% Polyvinylchloride under pressure of 30 MPa. The spherules were embedded in a resin and thin-sectioned with a diamond knife. Alignment of small aromatic layers in the spherules was studied by transmission electron microscopy using dark-field image and microdiffraction techniques. Based on the obtained dark-field images at various positions of the aperture on the 002 diffraction ring, a structural model for the as-prepared spherules has been proposed. In this model small aromatic layers are assumed to align approximately on circular conical surfaces with a common vertex in the spherule at or near the center of the spherule. The proposed model is supported by an electron microdiffraction study of various micro-areas of sections of the spherules. The model is also consistent with the deformation of spherules into thick disks and formation of a definite system of cracks in heat-treatment to 2800°C as revealed by scanning electron microscopy.