Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

EFFECTS OF VISCOSITY OF LIQUID FOODS ON PALATAL PRESSURE

The deglutition of non-Newtonian liquids introduced into the mouth was studied dynamically by measuring palatal pressure (P) with pressure transducers set at three locations on the palate. The value of P and the swallowing pressure (S) changed only from 100 to 200 g/cm² over the viscosity range 10⁻² to 10¹ Pa.s. The retaining time (T) and work (W), required for swallowing after the liquid entered the mouth, remained almost constant up to a critical value of 1.0 Pa.s. above which both T and W increased markedly. When the viscosity was low, all of the liquid was swallowed in one deglutition, up to 15 mL volume. Therefore, T was almost constant but S increased with the volume. When the viscosity was high, the liquid was swallowed in several smaller portions. When the volume was high, T increased and S was either constant or it decreased.     

Fe-Cr-Mn奥氏体合金的辐照体胀与诱起晶界偏析行为的研究SCIEI

本文采用电子束辐照,研究了Fe-15Cr-xMn合金以及添加W,V合金的孔洞体胀和诱起晶界偏析行为,并对包含晶界在内的辐照区进行成分分析。结果表明,在Fe-Cr-Mn系合金中孔洞体胀孕育期可以被强烈抑制,晶界偏析也减少。特别是,合金中添加W,V效果更加明显。用Mn代替Ni,通常要发生体胀和相的不稳定性,由于反Kirkendall效应导致Ni和Mn的扩散行为不同,使Fe富集在尾闾处,局部地区形成铁素体,有利于减少体胀和晶界偏析。     

基于UCON模型的PMI体系结构

基于角色的访问控制(RBAC)是授权管理基础设施PMI常用的策略,但它不能有效地解决资源使用中授权访问控制等动态授权问题.作为一种新型的访问控制技术,使用控制UCON模型具有支持动态授权等优势.基于UCON提出了一种授权管理体系结构UCB-PMI,并用可扩展访问标记性语言XACML描述其授权策略,最后分析了UCB-PMI的特点,     

展望21世纪新技术革命中的传感器

在回顾了以往产业革命中传感器的作用 ,比较工程传感器与人的感官的异同点之后 ,阐述了预计将于 2 1世纪爆发的新产业革命中传感器的使命及发展趋势     

双束强辐照对氧化物弥散强化铁素体型合金强化相稳定性影响

采用双束复合辐照装置,研究了He存在条件下,强辐照对长期时效后的ODS合金中强化相(Y2O3)的稳定性和辐照损伤特征的影响。实验结果表明:双束强辐照下,ODS合金中强化相不稳定,发生聚集长大并造成附近基体中Ti、Y浓度增高,导致空洞尺寸和空洞肿胀增加,并对这一结果从理论上进行解释。     

Iron Loss Analysis of Permanent Magnet Motors Fed by PWM Inverter

Carrier harmonic losses that consist of iron loss, eddy current loss, and ac copper loss are produced in a permanent magnet machine driven by a PWM inverter. It is already known that a higher motor inductance can lead to lower carrier harmonic losses. This paper investigates the carrier harmonic loss composition of two motors with identical dimensions but different inductances. The results of finite element analysis (FEA) showed that the eddy current loss in the iron core accounts for most of the carrier harmonic loss. It is also shown that the carrier harmonic loss of the iron core is quantifiable using theoretical calculations.     

如何受益硅烷偶联剂的奇妙功效

介绍了硅烷偶联剂的常规品种和新型产品：简述了硅烷偶联剂的作用机理和性能改进；总结了硅烷偶联剂的使用方法和注意要点：提出了只有正确使用才能奇效凸显，获益匪浅。     

基于GC-MS指纹图谱和化学计量学方法鉴别陈皮

制备了陈皮挥发油提取物并建立其气相色谱-质谱（GC-MS）指纹图谱,对不同批次的陈皮指纹图谱进行相似度评价;对其共有成分峰面积数据进行主成分分析（PCA）和层次聚类分析（HCA）。建立了具有16个共有峰的新会陈皮挥发油指纹图谱,通过化学计量学分析方法能将新会陈皮和其他陈皮样品准确区分开来;不同采摘期及贮存时间陈皮的成分呈现规律性特征。方法可用于不同产地、采摘期及贮存时间陈皮的鉴别,并为陈皮的质量控制提供依据。     

污水处理排放水对小流量河流水体生态的影响

针对日本国鬼怒河流域小流量河流,通过对河床上附着生物膜的组成、底栖生物、细菌活性分析和AGP试验,研究了污水厂二级处理排放水对小流量河流生态的影响.研究表明,当污水厂二级处理排放水占河流流量比例较大时(研究河流所占比例为35%),同样会引发河流富营养化和影响河流水体的生态.因此,从保护水环境及其生态考虑,有必要对污水进行深度处理.