Enhancement of properties of recycled coarse aggregate concrete using bacteria

Due to rapid construction, necessity for raw materials of concrete, especially coarse aggregate, tends to increase the danger of early exhaustion of the natural resources. An alternative source of raw materials would perhaps delay the advent of this early exhaustion. Recycled coarse aggregate (RCA) plays a great role as an alternative raw material that can replace the natural coarse aggregate (NCA) for concrete. Previous studies show that the properties of RCA concrete are inferior in quality compared to NCA concrete. This article attempts to study the improvement of properties of RCA concrete with the addition of bacteria named as Bacillus subtilis. The experimental investigation was carried out to evaluate the improvement of the compressive strength, capillary water absorption, and drying shrinkage of RCA concrete incorporating bacteria. The compressive strength of RCA concrete is found to be increased by about 20% when the cell concentration of B. subtilis is 10⁶ cells/ml. The capillary water absorption as well as drying shrinkage of RCA are reduced when bacteria is incorporated. The improvement of RCA concrete is confirmed to be due to the calcium carbonate precipitation as observed from the microstructure studies carried out on it such as EDX, SEM, and XRD.     

Dry machining of aluminum for proper selection of cutting tool: tool performance and tool wear

Machining of aluminum and its alloy is very difficult due to the adhesion and diffusion of aluminum, thus the formation of built-up edge (BUE) on the surface. The BUE, which affects the surface integrity and tool life significantly, affects the service and performance of the workpiece. The minimization of BUE was carried out by selection of proper cutting speed, feed, depth of cut, and cutting tool material. This paper presents machining of rolled aluminum at cutting speeds of 336, 426, and 540 m/min, the feeds of 0.045, 0.06, and 0.09 mm/rev, and a constant depth of cut of 0.2 mm in dry condition. Five cutting tools WC SPUN grade, WC SPGN grade, WC + PVD (physical vapor deposition) TiN coating, WC + Ti (C, N) + Al₂O₃ PVD multilayer coatings, and PCD (polycrystalline diamond) were utilized for the experiments. The surface roughness produced, total flank wear, and cut chip thicknesses were measured. The characterization of the tool was carried out by a scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) pattern. The chip underface was analyzed for the study of chip deformation produced after machining. The results indicated that the PCD tool provides better results in terms of roughness, tool wear, and smoother chip underface. It provides promising results in all aspects.     

Recovery of copper from a surface altered chalcopyrite contained ball mill spillage through bio-hydrometallurgical route

Bioleaching studies for chalcopyrite contained ball mill spillages are very scarce in the literature. We developed a process flow sheet for the recovery of copper metal from surface activated (600 °C, 15 min) ball mill spillage through bio-hydrometallurgical processing route. Bioleaching of the activated sample using a mixed meso-acidophilic bacterial consortium predominantly A. ferrooxidans strains was found to be effective at a lixiviant flow rate of 1.5 L/h, enabling a maximum 72.36% copper recovery in 20 days. Mineralogical as well as morphological changes over the sample surface were seen to trigger the bioleaching efficiency of meso-acidophiles, thereby contributing towards an enhanced copper recovery from the ball mill spillage. The bio-leach liquor containing 1.84 g/L Cu was purified through solvent extraction using LIX 84I in kerosene prior to the recovery of copper metal by electrowinning. Purity of the copper produced through this process was 99.99%.     

Effect of thermochemical and heat treatments on electroless nickel–boron

Electroless nickel–boron synthesized on mild steel was submitted different post-treatments (heat and thermochemical). The resulting surfaces were examined and characterized by scanning electron microscopy. XRD analysis was performed to investigate structural modifications. The samples were also tested under corrosion conditions and polarization measurements were performed.For both the as-plated and treated Ni–B coatings, correlations between electrochemical and microstructural characteristics were observed and it was found that post-treatments transform the coating to a crystalline form that increases corrosion resistance.     

Structural state of electroless nickel–boron deposits (5 wt.% B): Characterization by XRD and TEM

The structure of electroless nickel–boron with a boron content around 5 wt.% was investigated in the as deposited and heat treated states by X-ray diffraction and by transmission electron microscopy on thinned cross-sections prepared by focused ion beam technique.     

Dielectric relaxation and conduction mechanism of complex perovskite Ca0.90Sr0.10Cu3Ti3.95Zn0.05O12 ceramic

In this work, Sr and Zn co-doped calcium copper titanate having nominal formula Ca_0.90Sr_0.10Cu₃Ti_3.95Zn_0.05O₁₂ has been synthesized and systematically studied for structure, dielectric and electrical properties. The phase purity of the prepared composition has been confirmed by X-ray diffraction (XRD) pattern and various structural parameters are presented here with Rietveld refinement data. The Scanning electron microscopy (SEM) image revealed the presence of homogeneous fine-grained microstructure investigated in the prepared ceramic. The impedance data well fitted with 2 R-CPE model confirmed the non-ideality of the system. Dielectric studies have shown the existence of two relaxation processes in low and high frequency domains. Low frequency dielectric response proposed as a combination of Maxwell-Wagner relaxation and intrinsic defect (V_o⁺⁺) while high frequency behavior has been interpreted in terms of polaronic relaxation caused by hopping process of an electron between Ti³⁺ and Ti⁴⁺ states. The frequency dependent behavior of conductivity has been well fitted to Dong’s model and interpreted in term of Overlapping Large Polaron Tunneling (OLPT) mechanism. The various parameters; relaxation angular frequency (ω₁) of Debye process, ionic hopping frequency (ω₂₎, dc conductivity (σ_o), cole- cole parameter (α) and frequency exponent (s) have been determined by Dong’s Model fitting.     

Gene expression within cell-sized lipid vesicles

Functional protein synthesis was observed in cell-sized lipid vesicles following encapsulation of a gene-expression system. Expression of rsGFP (red-shifted green fluorescent protein) within individual vesicles was observed by fluorescence microscopy. Interestingly, at the early stage of the reaction, the expression efficiency inside the vesicle was remarkably higher than that in the solution outside. The synthesized rsGFP in individual vesicles is safe from attack by proteinase K added to the external aqueous solution. Studies on cell-sized vesicles expressing protein should contribute to a fundamental understanding of certain aspects of living systems and will be useful for practical applications, such as the construction of microreactors.     

Density estimation with minimization of U-divergence

This paper is concerned with density estimation based on the stagewise minimization of the U-divergence. The U-divergence is a general divergence measure involving a convex function U which includes the Kullback-Leibler divergence and the L ₂ norm as special cases. The algorithm to yield the density estimator is closely related to the boosting algorithm and it is shown that the usual kernel density estimator can also be seen as a special case of the proposed estimator. Non-asymptotic error bounds of the proposed estimators are developed and numerical experiments show that the proposed estimators often perform better than several existing methods for density estimation.     

Influence of Some Hofmeister Anions on the Krafft Temperature and Micelle Formation of Cetylpyridinium Bromide in Aqueous Solution

In this work, the effect of some Hofmeister anions on the Krafft temperature (T_K) and micelle formation of cetylpyridinium bromide (CPB) have been studied. The results show that more chaotropic anions increase, while the less chaotropic ones lower the T_K of the surfactant. More chaotropic I^? and SCN^? form contact ion pairs with the cetylpyridinium ion and reduce the electrostatic repulsion between the CPB molecules. As a result, these ions show salting‐out behavior, with a consequent increase in the T_K. In contrast, less chaotropic Cl^? and NO₃^? increase the activity of free water molecules and enhance hydration of CPB molecules, showing a decrease in the T_K. A rather unusual behavior was observed in the case of SO₄^2? and F^?. These strong kosmotropes shift from their usual position in the Hofmeister series and behave like moderate chaotropes, lowering the T_K of the surfactant. Because of the high charge density and the strong tendency for hydration these ions preferentially remain in the bulk. Rather than forming contact ion pairs, these ions stay away from the CPB molecules, decreasing the T_K of the surfactant. In term of decreasing the T_K, the ions follow the order NO₃^? > SO₄^2? > Cl^? > F^? > Br^? > SCN^? > I^?. The critical micelle concentration (CMC) of the surfactant decreases significantly in the presence of these ions due to the screening of the micelle surface charge by the excess counterions. The decreasing trend of the CMC in the presence of the salts follows the order SCN^? > I^? > SO₄^2? > NO₃^? > Br^? > Cl^? > F^?.