Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

Biotransformation of three aromadendrane‐type sesquiterpenoids by Aspergillus wentii

BACKGROUND: The biotransformation of sesquiterpenoids, which are a large class of naturally occurring compounds, using microorganisms as a biocatalyst to produce useful novel organic compounds was investigated. The biotransformation of sesquiterpenoids, (+)‐aromadendrene ( 1 ), (−)‐alloaromadendrene ( 2 ) and (+)‐ledene ( 3 ) has been investigated using Aspergillus wentii as a biocatalyst. Results: Compound 1 was converted to (−)‐(10S,11S)‐10,13,14‐trihydroxyaromadendrane ( 4 ). Compound 2 was converted to (+)‐(1S,11S)‐1,13‐dihydroxyaromadendrene ( 5 ) and (−)‐5,11‐epoxycadin‐1(10)‐en‐14‐ol ( 6 ). Compound 3 was converted to compound 6 , (+)‐(10R,11S)‐10,13‐dihydroxyaromadendr‐1‐ene ( 7 ) and (+)‐(10S,11S)‐10,13‐dihydroxyaromadendr‐1‐ene ( 8 ). The structure of the metabolic products has been elucidated on the basis of their spectral data. CONCLUSION: Compound 1 gave only one product that was hydroxylated at C‐10, C‐13 and C‐14. By contrast, compounds 2 and 3 gave a number of products, one of which was common. The differences in oxidation of 1–3 are due to the configuration of the C‐1 position. Compounds 4–8 were new compounds. Copyright © 2008 Society of Chemical Industry     

On A Maximum Likelihood Method for Clustering

Behaviormetrika - In this paper, we propose a new clustering method based on the concept of maximum likelihood (ML) estimation. In general, the problem of local minima arises when we try to use the...     

Boron removal by titanium addition in solidification refining of silicon with Si-Al melt

In order to effectively remove B from Si for its use in solar cells, a process involving B removal by solidification refining of Si using a Si-Al melt with Ti addition was investigated. For clarifying the effect of Ti addition on B removal from the Si-Al melt, TiB₂ solubilities in Si-64.6 at. pct Al melt at 1173 K and Si-60.0 at. pct Al melt at 1273 K were determined by measuring the equilibrium concentrations of B and Ti in the presence of TiB₂ precipitates. The small solubilities of TiB₂ in the Si-Al melt indicate the effective removal of B from the Si-Al melt by Ti addition. Further, solidification experiments of Si-Al alloys containing B by Ti addition were performed, and the effect of Ti addition on the solidification refining of Si with the Si-Al melt was successfully confirmed.     

Hierarchical Clustering Method Using Probabilistic Similarity Measure

In this paper, we propose a new hierarchical clustering method, which is useful to find appropriate clusters of attributes from given dichotomous or frequency data. Important features of our method are 1) the similarity between two attributes is defined as a probability of their pattern vectors being observed under the hypothesis of independence, 2) for each generated cluster, one pattern vector is defined in a natural manner, and 3) it can be used freely without distinguishing the frequency data from the dichotomous one.

A typical frequency data is analyzed to illustrate how our method works effectively. The discussion on similarities among objects is also included to propose a new similarity measure based on our clustering method.

     

Flexural properties of moldings of rigid polyurethane made by reaction injection molding

Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM.     

Phase Separation in Gelling Silica–Organic Polymer Solution: Systems Containing Poly(sodium styrenesulfonate)

Phase separation which occurs in parallel to the hydrolysis and gelation of alkoxysilane solution containing poly(sodium styrenesulfonate) (NaPSS) has been investigated. Depending on the reaction conditions, gel morphologies such as isolated pores, particle aggregates, and interconnected continuous pores from 0.1 to 100 μm long have been observed. Time-resolved light scattering of gelling solution suggested the occurrence of spinodal phase separation through the polymerization of silica and the subsequent freezing of the developing structure by sol-gel transition. The effects of reaction parameters on the periodic size are explained mainly in terms of their influence on the "chemical cooling" rate which is determined by the polymerizatica rate of silica and the solubility of NaPSS in the reacting solution.     

An Application of Silica‐Based Monolithic Membrane Emulsification Technique for Easy and Efficient Preparation of Uniformly Sized Polymer Particles

Summary: Uniformly sized polymer particles were prepared by an emulsification and polymerization technique utilizing a silica monolithic membrane, namely the “silica monolithic membrane emulsification technique”. In this paper, we utilized silica monolithic membrane as a device for the preparation of uniformly sized polymer particles. A mixture of monomers, diluents and oil‐soluble initiator was emulsified into a continuous medium through the silica monolithic membrane and polymerized. The particles obtained had a higher size uniformity than that of particles prepared by previously reported membrane emulsification techniques, such as the Shirasu Porous Glass (SPG) emulsification technique. Through the silica monolithic membrane emulsification technique, we could prepare particles having availability as a possible packing material for solid‐phase extraction (SPE) and high performance liquid chromatography (HPLC).

SEM photograph of silica particles prepared through capillary plate membrane.     

Transmission of correct gaze direction in video conferencing using screen-embedded cameras

In this paper, we propose a new video conferencing system that presents correct gaze directions of a remote user by switching among images obtained from multiple cameras embedded in a screen according to a local user’s position. Our proposed method reproduces a situation like that in which the remote user is in the same space as the local user. The position of the remote user to be displayed on the screen is determined so that the positional relationship between the users is reproduced. The system selects one of the embedded cameras whose viewing direction towards the remote user is the closest to the local user’s viewing direction to the remote user’s image on the screen. As a result of quantitative evaluation, we confirmed that, in comparison with the case using a single camera, the accuracy of gaze estimation was improved by switching among the cameras according to the position of the local user.