Successful eradication of H. pylori in an elderly patient with gastric cancer after effective UFT-E therapy

The patient was a 83-year-old female with 2' T2-type gastric cancer associated with positive H. pylori in the lesser curvature of the stomach. The patient was treated with oral UFT-E alone in a daily dose of 400 mg. The tumor exhibited an O' IIa + IIc-like appearance 4 weeks after the start of administration and became scarred 8 weeks later, revealing marked tumor reduction in a short period of time. At 8 weeks, biopsy showed marked polymorphonuclear cells infiltration of gastric mucosa with no evidence of malignancy. In an attempt to eradicate H. pylori, 30 mg of lansoprazole, 400 mg of clarithromycin, and 2.0 g of ecabet-Na (3.0 g of Gastrom) were administered for 2 weeks. H. pylori was found to have been successfully eradicated, and the inflammatory lesions were no longer visible histologically. UFT-E was highly effective in this patient, and the eradication of H. pylori may contribute to the prevention of cancer recurrence.     

A video DSP with a macroblock-level-pipeline and a SIMD typevector-pipeline architecture for MPEG2 CODEC

A video DSP with macroblock-level-pipeline and a SIMD type vector-pipeline architecture (VDSP2) has been developed, using 0.5 μm triple-layer-metal CMOS technology. This 17.00 mm×15.00 mm chip consists of 2.5 M transistors, and operates at 100 MHz. The real-time encoder and decoder specified in the MPEG2 main profile at the main level can be realized with two VDSP2's and a motion estimation (ME) unit, and one VDSP2 respectively, at an 80 MHz clock rate, with a total power dissipation of 4.2 W at 3.3 V     

Superconductivity in W-containing diamond-like nanocomposite films

Superconductivity in a tungsten-containing carbon-oxide film was reported. The film with 500 nm thickness was deposited onto polycrystalline silicon oxides using chemical vapor deposition and the co-sputtering of a tungsten metal target. The bonding state of the carbon atoms and the macroscopic and microscopic crystal structure of the film were investigated by Raman spectroscopy, X-ray diffraction and transmission electron microscopy measurements. From the experimental results, we determined that this film essentially had an amorphous structure. The temperature dependence on resistivity was measured in the temperature range of 2–300 K. Resistive superconducting transition was observed at 3.8 K. The dc magnetizations were measured in the temperature range of 1.8–6.5 K. The diamagnetism resulting from a superconductive state was observed below 3.75 K, which is consistent with a resistive superconducting transition. It is thought that the finite sized clusters of the different superconductive transition temperatures cooperatively produce a macroscopic superconducting phenomenon.     

Young’s modulus of crystalline C60 nanotubes studied by in situ transmission electron microscopy

Bending tests of crystalline nanotubes composed of fullerene C₆₀ molecules are performed inside a high-resolution transmission electron microscope. We fixed one side of a C₆₀ nanotube with a body-centered tetragonal structure with typical inner and outer diameters, i.e., 180 nm and 510 nm, respectively, and then applied concentrated forces on the other side using piezomanipulation of a silicon nanotip. The bending process was observed in situ by transmission electron microscopy with simultaneous measurements of the forces by an optical deflection method. It was found that the Young’s modulus of the nanotube was estimated to be 62–107 GPa, which was 1.1–3.3 times larger than that of C₆₀ nanowhiskers. The result concerning the increase in the Young’s modulus of the C₆₀ nanotube provided an experimental evidence for the structural model composed of an inner core and a surface shell for C₆₀ nanowhiskers.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

Fabrication of large area diffraction grating using LIGA process

X-ray imaging is a very important technology in the fields of medical, biological, inspection, material science, etc. However, it is not enough to get the clear X-ray imaging with low absorbance. We have produced a diffraction gratings for obtaining high resolution X-ray phase imaging, such as X-ray Talbot interferometer. In this X-ray Talbot interferometer, diffraction gratings were required to have a fine, high accuracy, high aspect ratio structure. Then, we succeeded to fabricate a high aspect ratio diffraction grating with a pitch of 8 μm and small area using a deep X-ray lithography technique. We discuss that the diffraction gratings having a narrow pitch and an large effective area to obtain imaging size of practical use in medical application. If the pitch of diffraction gratings were narrow, it is expected high resolution imaging for X-ray Talbot interferometer. We succeeded and fabricated the diffraction grating with pitch of 5.3 μm, Au height of 28 μm and an effective area of 60 × 60 mm².     

A full‐color eyewear display using planar waveguides with reflection volume holograms

Abstract— A full‐color eyewear display with over 85% see‐through transmittance with a 16° horizontal field of view was developed. Very low color crosstalk, less than 0.008 Δu′v′ uniformity, and 120% NTSC color gamut were achieved. Waveguides with two in‐ and out‐coupling reflection volume hologram elements enabled a simple configuration that has an optical engine beside the user's temples. The reflection volume hologram elements used on the waveguides realized a small thickness of 1.4 mm for each waveguide, and an out‐coupling reflection volume hologram used as an optical combiner contributed a high see‐through transmittance of 85% due to its wavelength selectivity. However, there are technical challenges in achieving a reasonable screen size and quality color images with optics that utilize holographic waveguides because holograms have large chromatic dispersions compared to conventional optical elements such as lenses and mirrors. Approaches to overcome these issues are described.     

Active sensing control improving SLAM accuracy for a vehicle robot

Artificial Life and Robotics - This study considers an autonomous mobile vehicle using SLAM technology in an unknown environment. The focused problem is the decrease of trajectory following...     

Correction to: Development of a behavioral trajectory measurement system (Bucket-ANTAM) for organisms moving in a two-dimensional plane

Artificial Life and Robotics -     

Relation between axial compressive strength of reinforcing fibres and fibre diameter

Attempts were made to estimate the fibre axial compressive strength of pitch-based graphitized and polyarylate fibres, and the relationship between the compressive strength and fibre diameter was investigated. The estimated compressive strength of fibres decreases with increasing temperature. This decrease in compressive strength may be accounted for by a decrease in the radial compressing force. There is a linear relationship between the estimated compressive strength and radial compressing force in a temperature range from room temperature to 80°C. The real compressive strength of the fibres, determined by extrapolating this straight line until the radial compressing force is zero, increases with decreasing fibre diameter, but remains almost unchanged at a diameter range smaller than 10 m. In order to obtain reinforcing fibres having a higher compressive strength, it will be necessary to prepare fibres having a diameter smaller than 10 m.