Breakdown of oil films and formation of residual films

The breakdown processes of oil films under quasi-static loading have been investigated by using a newly developed steel-oil-mercury system. The relationship between the thickness and breakdown ratio of a hexadecane film is represented by a single master curve independently of the indentation speed, indentation load, and temperature. The master curve shows that the breakdown process of hexadecane includes two stages; one is the decrement of the thickness without breakdown and the other is the decrement of the thickness with a drastic progress of breakdown. By solving a small amount of fatty acid in hexadecane, the thickness increases and the breakdown ratio decreases noticeably; a multilayer residual film supporting normal load is formed between two metal surfaces. Experiments at different temperatures reveal a negative relationship between the temperature and thickness of residual film, which indicates that the residual film is organized by physical interaction rather than chemical interaction. At least under a lower concentration, the residual film appears to consist of not only fatty acid molecules but also hexadecane molecules.     

Structural Changes in Titin and Nebulin Filaments Specific to Calcium Ions at 0.1 mM: Factors of Meat Tenderization During Postmortem Aging

ABSTRACT Postmortem structural changes in titin and nebulin filaments were investigated by incubating isolated myofibrils in a solution containing 0.1 mM calcium ions and various concentrations of a protease inhibitor. The inhibition curves showed 2 abnormal steps with increases in the concentration of leupeptin or calpastatin domain I. While the amounts of unchanged titin and nebulin were constant in the 1st step, the 2nd occurred at higher protease inhibitor concentrations. These facts indicated that excess amounts of leupeptin and calpastatin domain I caused deterioration in titin and nebulin properties, thus interfering with the binding of calcium ions. We concluded that the severance of titin and nebulin filaments in the 1st step were induced by calcium ions at 0.1 mM.     

Catalytic decomposition of HCFC22 (CHClF2)

The catalytic decomposition of CHClF₂ was studied over various acidic metal oxides in a fixed-bed reactor. The Cr₂O₃ZrO₂ exhibited the highest activity. The presence of water vapor in the reaction system suppresses the transformation of oxides to fluorides, progresses the formation of CO₂, and it improves the catalysts life.     

Design of one-dimensional ferromagnet based on polyacetylene chain

As a model for organic ferromagnetism in a one-dimensional system, substituted polyacetylenes are re-considered on the basis of the molecular orbital (MO) and the crystal orbital (CO) methods. The semiempirical MO calculations with configuration interaction for the dimer model show that the exchange interaction on poly[(4-oxyphenyl)acetylene] (1) is negative in spite of Ovchinnikov's prediction, due to the direct interaction between the adjacent pendant spins. On the other hand, it is shown that a polyacetylene chain with phenoxy radicals as pendants on every other active site can become a one-dimensional feromagnet. Moreover, the CO calculations by means of the unrestricted Hartree-Fock method give a theoretical background for the realization of a ground state with macroscopic spin alignment on the improved model chain.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%     

Rutile-type TiO2 thin film for high-k gate insulator

We investigated rutile-type titanium dioxide (TiO₂) films for possible use as a high-k gate insulator. The TiO₂ thin films were directly deposited on Si substrates using a RF magnetron sputtering method with a sintered oxide target. A single phase of rutile-type TiO₂ whose dielectric constant of approximately 75 was obtained when the film was deposited in an inert gas atmosphere and annealed at 800 °C in an oxidizing gas atmosphere. The oxygen ions were deficient in the as-deposited film, and consequently, a sufficient oxygen supply was needed to crystallize the film to a single phase of rutile during the post-annealing. However, the interfacial SiO₂ layer between the TiO₂ and the Si substrate simultaneously grew thicker than 2 nm. As the interfacial SiO₂ grew, the leakage current was decreased and the equivalent oxide thickness was increased, in the Au/rutile-type TiO₂/Si capacitor. Therefore, we concluded that the growth of the interfacial SiO₂ layer thicker than 2 nm is inevitable to form the single phase of rutile-type TiO₂ and to decrease the leakage.     

Neutronic and thermodynamic feasibility of UF6-NpF6 fueled transmutation reactor

Transmutation of neptunium, which is contained in radioactive wastes discharged from nuclear reactors, was investigated as a substitutional method for geologic disposal. We proposed a transmutation reactor fueled with a mixture of gaseous ²³³UF₆ and ²³⁷NpF₆. Neutronic and thermodynamic analysis of the reactor revealed the feasibility of the concept. The reactor has two principal advantages: (1) use of the fuel gas enables on-line reprocessing, (2) ²³⁷Np can be transmuted by a high neutron flux. Our calculation indicated that the transmutation rate of ²³⁷Np was 335 g/year/MW_th, which is much larger than the annual yield of ²³²Np in PWR (6.19 g/year/MW_th).     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.