Performance prediction of a hybrid‐excitation synchronous machine with axially arranged excitation poles and permanent‐magnet poles

This paper presents a method of predicting the steady‐state performance of a new hybrid‐excitation synchronous machine (HESM) theoretically. The field pole of this HESM is axially divided into two parts; one is an excitation part and the other a permanent‐magnet (PM) part. A nonlinear equivalent circuit, which can include the saliency of the rotor and the magnetic saturation due to the iron core, is derived. Based on this equivalent circuit, the steady‐state performance of the HESM is calculated, and the results are confirmed through experiments. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 43–49, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20033     

Reliability of Au bump––Cu direct interconnections fabricated by means of surface activated bonding method

As a room temperature bonding method, surface activated bonding (SAB) method has been introduced to be one of the most appropriate interconnection methods for the next generation of electronic packaging. Thus it is important to study the reliability of SAB interconnection in long term life test.In this paper, interconnections of Au bump and Cu film bonded by SAB method were performed in high temperature thermal aging test. Degradation of properties such as electrical resistance, shear strength of bump and interface microstructure during aging process were studied to investigate the failure mechanism of the interconnection. Intermetallic compound Cu₃Au was found formed at the interface during thermal aging, and it causes evolvement of the properties and failure mode of the interconnection changing in shear test. Results reveal that SAB is suitable for the interconnection between Au bump and Cu film and it is reliable in thermal reliability test.     

The influence of side chains on formation of inclusion complexes prepared with polyolefin and cyclodextrins

We investigated the formation of inclusion complexes (ICs) between cyclodextrins (CDs) with different cavity size and polyolefin (PO) with different side chains by using Fourier transform infrared (FTIR) spectroscopy, wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry. The analysis of FTIR spectra revealed that the resultants were complexes of CD and PO, and the analysis of WAXD revealed that the molecules of CD had a channel structure due to the formation of ICs. We found that IC could not be obtained when the cavity size of CD was small for PO molecules to thread and it was too large for cross-sectional area of PO molecules. Thus, it was found that PO1 with few side chains could form IC with α-CD, and PO2 with ethyl side chain could form IC with β-CD and γ-CD, while the PO3 with 2-methyl-propyl side chain could form IC with γ-CD. These results suggest that the cross-sectional areas of polymer and the cavity size of CDs play critical roles in the formation of ICs. It is only possible to form ICs when the polymer chains can tread into cavities of CDs, and the space between the polymer and CD is suitable to provide enough intermolecular interaction to keep the structure of IC stable.     

Compensation for neutral current harmonics in a three-phase four-wire system by a synchronous machine

This paper presents a new method that passively reduces the neutral current harmonics in a three-phase four-wire system by a synchronous machine. Selecting 2/3 as the coil pitch of the armature winding can minimize the zero-sequence reactance of the synchronous machine. The proposed method utilizes such a characteristic, which allows harmonic compensation by the synchronous machine. For analysis and design, an equivalent circuit for the third harmonic component of the basic system is derived. Using this equivalent circuit, its harmonic compensation characteristics are theoretically analyzed and design fundamentals are provided. Experimental results demonstrate the effectiveness of the proposed method and validate the theoretical analysis.     

Nucleation effect of inclusion complexes with different polyolefin as guest molecules on the crystallization of polypropylene

The γ‐cyclodextrin (γ‐CD) inclusion complexes (ICs) with four kinds of polyolefin (PO) as guest molecules were prepared. The crystallization behavior of isotactic polypropylene (iPP) blended with the γ‐CD and γ‐CD–PO ICs was investigated by differential scanning calorimetry, polarized optical microscopy, and light scattering. The iPP blended with the ICs was found to exhibit higher crystallization temperature (T_C), smaller spherulites, and faster crystallization rate than those of neat iPP, indicating that the ICs play a role of nucleating agent on the crystallization of iPP and induce accelerated crystallization. The IC with PO having higher T_C as guest molecules showed higher nucleation effect than the IC with PO having lower T_C as guest molecules. The results suggest that the nucleation effect of these ICs was affected by the kinds of the guest molecules. The higher T_C guest molecules could result in higher nucleation effect. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Technical investigation on small water leakage incident occurrence in mercury target of J-PARC

Japan Proton Accelerator Research Complex experienced failures of two mercury targets, which were Target #5 and #7, in 2015 when the facility was operating with a proton beam power of 500 kW. The failures involved coolant water leak from the water shroud. In this paper, we investigate the root cause of the Target #5 failure. The results of the visual inspections, mockup tests, and analytical evaluations suggested that the water leak was caused by the possible combination of two incidents. One was the diffusion bonding failure due to the large thermal stress induced by welding of the bolt head during the fabrication process, and the other was the thermal fatigue failure of the seal weld due to the repetitive beam shutdown during beam operation. Though the investigation into the root cause of the Target #7 failure is still going on, these target failures point to the importance of eliminating initial defects and the need to secure the rigidity and stability of welded structures. The next mercury target, Target #8, was fabricated with an improved design and fabrication process to reduce the possibility of similar failures. The beam operation of this mercury target is planned to be started in October 2017.     

Erosion damage of laser alloyed stainless steel in mercury

The effect of laser surface alloying of type 316 stainless steel on the erosion resistance in mercury has been investigated. The alloying was produced by melting predeposited Al-Si powder and a portion of underlying substrate with a pulsed Nd:YAG laser beam. The microhardness of the modified layer was found to be 2.5 times higher than that of untreated steel. The erosion test of laser alloyed surface and steel in mercury was carried out by using the electromagnetic impact testing machine. The laser alloyed surface was found to be less damaged after 10⁵ cycles of impacts compared to untreated stainless steel. However, after 10⁶ cycles the erosion resistance of the modified layer is much lower than that of untreated steel. Liquid metal embrittlement in contact with mercury and residual stresses were considered as factors impairing the erosion resistance of the laser alloyed surface.     

Internal tandem duplication of the FLT3 gene is preferentially seen in acute myeloid leukemia and myelodysplastic syndrome among various hematological malignancies. A study on a large series of patients and cell lines

In this study, we examined a large number of patients to clarify the distribution and frequency of a recently described FLT3 tandem duplication among hematopoietic malignancies, including 112 acute myelocytic leukemia (AML), 55 acute lymphoblastic leukemia (ALL), 37 myelodysplastic syndrome (MDS), 20 chronic myelogenous leukemia (CML), 30 non-Hodgkin's lymphoma (NHL), 14 adult T cell leukemia, 15 chronic lymphocytic leukemia (CLL) and 38 multiple myeloma (MM). We also evaluated 71 cell lines derived from 11 AML, 31 ALL, two hairy cell leukemia, three acute unclassified leukemia, 10 CML, 12 NHL including six Burkitt's lymphoma, and two MM. Using genomic PCR of exon 11 coding for the juxtamembrane (JM) domain and first amino acids of the 5'-tyrosine kinase (TK) domain, this length mutation was found only in AML (22/112, 20%) and MDS (1/37). According to the FAB subclassification, they were 5/18 (28%) of M1, 4/29 (14%) of M2, 3/17 (18%) of M3, 6/24 (25%) of M4, 4/20 (20%) of M5 and 1/9 of refractory anemia with excess of blast in transformation. In the various cell lines examined, this abnormality was determined in only one derived from AML and never found in other hematological malignancies. The sequence analysis of the abnormal PCR products revealed that 23 of 24 showed internal tandem duplication with or without insertion of nucleotides. In one AML, insertion and deletion without duplication was determined. All 24 lengthened sequences were in-frame. Duplication takes place in the sequence coding for the JM domain and leaves the TK domain intact. In conclusion, we emphasize that the length mutation of FLT3 at JM/TK-I domains were restricted to AML and MDS. Since all these mutations resulted in in-frame, this abnormality might function for the proliferation of leukemic cells.