Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Adhesion of streptococci to saliva-coated and uncoated composite-based resins

This study was designed to evaluate the bacterial adhesion to five types of experimental composite-based resins and a commercial composite resin used as a control. Physicochemical surface characteristics of composite resins with and without an artificial saliva coating were measured. The relationship between the numbers of adhering cells (Streptococcus sanguis, S. mutans and S. sobrinus) and surface characteristics was analysed. The values of contact angles and the number of adhering cells were small with saliva coating. S. sanguis ATCC 10557 showed a positive correlation (r=0.835, p<0.05) with the contact angles of uncoated resins, whereas no relationship was observed for saliva-coated resins. With S. mutans Ingbritt the cell numbers adhering to resins correlated strongly (p<0.01) with the values of zeta potential of resins for either saliva coated or uncoated. Electrical repulsion forces had a strong contribution to adherence of cells such as S. mutans and S. sobrinus which show a high absolute zeta potential.     

Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

Latest advances in camcorder technology

Camcorders have been developed to be compact with high performance. Latest advancement of key technologies and devices such as digital signal processing LSI, six-layer printed circuit board with micro chips, high-speed power lens with linear motor, 103 K pixels 0.7-in LCD electronic viewfinder, and high-energy Li-ion battery are described. High-band format is also explained     

GBLT-VG for High User Densities by User Group Behavior and Hot Point in MMO Virtual Environment

Massively Multiplayer Online (MMO) games have large-scale virtual environments. Here, we propose a load distribution technique called the Group Based Load-distribution Technique with Virtual Group (GBLT-VG) that utilizes Peer-to-Peer (P2P) communication to maintain scalability under high user density conditions in MMO virtual environments. A common problem of P2P virtual environments is that user group behavior frequently generates high user density conditions. Existing techniques to manage the virtual environment cannot maintain performance in such high user density situations. The proposed technique, GBLT-VG, reduces area management loads of manager peers by introducing a new manager who manages a user neighbor group. GBLT-VG forms the user neighbor group efficiently by using party function under high user density conditions caused by users?? cooperative behaviors. In addition, GBLT-VG reduce the management load by using a virtual group when a number of parties is small, thereby decreasing the existing managers?? loads dynamically. This paper also presents simulation results demonstrating how GBLT-VG can reduce the average number of users managed by the server.     

Laser-Sintered Barium Titanate

Laser sintering of alkoxy-derived ultrafine BaTiO₃ powders was investigated. The temperature increases of the sample with laser irradiation were measured with a thermocouple. It was found that laser irradiation could generate enough heat to sinter ceramics. A slurry was prepared by mixing an alkoxy-derived BaTiO₃ powder, binder additives, solvent, and plasticizer. The slurry was tape cast and dried to give a green sheet. The green sheet was laser sintered and was then characterized by SEM, XRD, and density measurements. The effect of burnout before laser irradiation and the characteristic microstructure of laser-sintered BaTiO₃ are described.     

Conductive Papers Containing Metallized Polyester Fibers for Electromagnetic Interference Shielding

Conductive papers were developed for preventing or reducing electromagnetic interference (EMI), and their shielding efficiency was evaluated. This type of conductive paper consists of wood pulp, synthetic pulp and metallized polyester fibers (0.5–2.0 mm long and 14 m in diameter) whose surfaces are coated with nickel alone (Ni-PET) or copper and nickel double layers (Ni-Cu-PET) by electroless plating. In this report, the effect of the characteristics of these metallized fibers, such as their conductivity, geometry and the concentration of fibers in paper, which lead to high efficiency for shielding effectiveness is discussed. For instance, one of the conductive papers (80 g/m2) which was prepared by mixing 40% Ni-Cu-PET and 60% synthetic polyethylene pulp showed over 40 dB shielding effectiveness between 10 MHz and 1 GHz.     

Effect of Grain Boundaries on Thermal Conductivity of Silicon Carbide Ceramic at 5 to 1300 K

The thermal conductivity of a SiC ceramic was measured as 270 W·m⁻¹·K⁻¹ at room temperature. At low temperatures ( T < 25 K), the decrease in the conductivity was proportional to T ³ on a logarithmic scale, which indicated that the conductivity was controlled by boundaries. The calculated phonon mean free path in the ceramic increased with decreased temperature, but was limited to ∼4 μm, a length almost equal to the grain size, at temperatures below 30 K. We concluded that the thermal conductivity of the ceramic below 30 K was influenced significantly by grain boundaries and grain junctions.     

Barium Carbonate Phase on the Surfaces of Barium Titanate Particles and in Situ Transmission Electron Microscopy Observation of Its Decomposition

A BaCO₃ phase is found on the surfaces of hydrothermally synthesized BaTiO₃ particles; it occurs as aggregates or small protuberances. A small proportion of the phase decomposes to BaO crystallites when heated by a convergent electron beam in a transmission electron microscope. The BaO and BaCO₃ crystallites disappear when they are irradiated successively by the convergent electron beam. The BaO crystallites and the BaCO₃ phase sublimate and/or react with BaTiO₃ crystals whose surface layers are deficient in Ba²⁺ ions.