Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Structure-activity relationships of alkylxanthines: alkyl chain elongation at the N1- or N7-position decreases cardiotonic activity in the isolated guinea pig heart

Relationships between the alkyl substitutions (C1-C6) and cardiac inotropic activities of xanthine derivatives were studied in isolated guinea pig heart muscles. Most of the alkylxanthines exhibited positive inotropic activity on the left atrium, which was increased with an elongation of alkyl chain at the N3-position but decreased by substitution of a long alkyl group at the N1- or N7-position of the xanthine skeleton. Although positive inotropic activity in the right ventricular papillary muscle was also increased by longer alkyl groups at the N3-position, the inotropic activity became negative with an increment in alkyl chain length at the N1- or N7-position. The positive inotropic activity of alkylxanthines was correlated with their inhibitory activity on the phosphodiesterase (PDE) III isoenzyme. Adenosine A1 antagonism and PDE IV inhibitory activity were also partly associated with the inotropic activity because H-89, an inhibitor of cyclic AMP-dependent protein kinase, diminished the positive inotropic action and potentiated the negative inotropic action. These results indicate that the positive inotropic activity of alkylxanthines becomes weak with elongation of alkyl chains at the N1- and N7-positions; In particular, xanthines having two long alkyl chains show a negative inotropic activity on the right ventricular papillary muscle, an effect that could not be elucidated from their cyclic AMP-dependent action.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Development of `information collection and delivery sensor basesystem' for large-scale power systems

The authors present a real-time database system capable of collecting and delivering a large amount of information accurately at a high speed and by a simple method. This system has a microprocessor unit (MPU) for each private communication line around the main memory and coordinates the independent parallel operation for a number of these MPUs with the main memory access operation, using a fixed cyclic scan method and having all the MPUs perform multi-operation. Many advantages can be expected when this method is adopted, especially for the monitoring and control of power systems. Degradation of the system can be avoided during an information rush due to accidents, and it can be easily extended when adding to or expanding the power facilities in the future. Excellent daily maintainability can be assured, and a low overall cost can be expected     

Current Understanding of the Structure,Stability and Dynamic Properties of Amyloid Fibrils

Amyloid fibrils are supramolecular protein assemblies represented by a cross-β structure and fibrous morphology, whose structural architecture has been previously investigated. While amyloid fibrils are basically a main-chain-dominated structure consisting of a backbone of hydrogen bonds, side-chain interactions also play an important role in determining their detailed structures and physicochemical properties. In amyloid fibrils comprising short peptide segments, a steric zipper where a pair of β-sheets with side chains interdigitate tightly is found as a fundamental motif. In amyloid fibrils comprising longer polypeptides, each polypeptide chain folds into a planar structure composed of several β-strands linked by turns or loops, and the steric zippers are formed locally to stabilize the structure. Multiple segments capable of forming steric zippers are contained within a single protein molecule in many cases, and polymorphism appears as a result of the diverse regions and counterparts of the steric zippers. Furthermore, the β-solenoid structure, where the polypeptide chain folds in a solenoid shape with side chains packed inside, is recognized as another important amyloid motif. While side-chain interactions are primarily achieved by non-polar residues in disease-related amyloid fibrils, the participation of hydrophilic and charged residues is prominent in functional amyloids, which often leads to spatiotemporally controlled fibrillation, high reversibility, and the formation of labile amyloids with kinked backbone topology. Achieving precise control of the side-chain interactions within amyloid structures will open up a new horizon for designing useful amyloid-based nanomaterials.