Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Structure and dynamics of suspensions of silica particles in liquidcrystals under a low frequency AC applied voltage

Silica particles dispersed in liquid crystals exhibit a novel behavior such as a unique migrating behavior and alignment. These characteristics are found to depend on the size of the nanoparticles, the surface state of nanoparticles, the liquid crystal (LC) phases, the amplitude and the frequency of applied voltage. These are discussed in terms of anisotropic particle-particle and particle-LC molecules interactions in the anisotropic environment of liquid crystal matrix     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Forming mental models in learning operating procedures for terminalequipment

People faced with an unfamiliar product or service tend to fall back on mental models based on analogical relationships with familiar products or services. Two experiments on the analogical relationships or metaphors that people might use when operating a communications terminal are described. In the first experiment, the role previously acquired operating knowledge has in determining the mental models people use when directory dialing with novel equipment is examined. In a second experiment, it is shown that an explicit appeal to an analogy between conventional mail and electronic mail can help users learn to use an electronic mail system, and make it easier for them to remember how to use the system as long as 90 days after initial exposure. It is concluded that the mental model is constructed only from the user's operating knowledge acquired as a result of past experiences, and the metaphor method is effective when the instructions are metaphorically taught     

Using precise data sets on farming and pesticide properties to verify a diffuse pollution hydrological model for predicting pesticide concentration.

Verification of a diffuse pollution model involves comparing results actually observed with those predicted by precise model inputs. Acquisition of precise model inputs is, however, problematic. In particular, when the target catchment is large and substantial estimation uncertainty exists, not only model verification but also prediction is difficult. Therefore, in this study, rice-farming data were collected for all paddy fields from all farmers in a catchment and pesticide adsorption and degradation rates in paddy field soil samples were measured to obtain precise model inputs. The model inputs successfully verified the model's capability to predict pesticide concentrations in river water. Sensitivity analyses of the model inputs elucidated the processes significantly affecting pesticide runoff from rice farms. Pesticide adsorption and degradation rates of the soil did not significantly affect pesticide concentrations, although pesticide discharge to river water accounted for less than 50% of the total quantity of pesticide applied to fields, possibly owing to pesticide adsorption and degradation. The timing of increases in pesticide concentrations in river water was affected mostly by the farming schedule, including the time of pesticide application and irrigation, and secondarily by rainfall events.