Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Preparation of micrometer‐sized,monodisperse, magnetic polymer particles

Micrometer‐sized, monodisperse, magnetic composite particles were prepared by heating micrometer‐sized, monodisperse, hollow polystyrene/polydivinylbenzene composite polymer particles at 200°C for 4 h (particles had been dipped in pentacarbonyliron) and then washed in 12 N HCl and water. The hollow polymer particles were produced by seeded polymerization by the dynamic swelling method that was proposed by authors. The magnetic composite particles contained Fe₃O₄, the content of which was 49% based on total weight, and were attracted easily in water by a 1650 G magnet. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 428–433, 2003     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Microscopic fatigue processes in a plain-weave glass-fibre composite

This paper focuses on the microscopic damage and progressive failure of a composite reinforced by plain-weave glass cloth under tensile fatigue loading. The fatigue process was divided into three stages like that of multi-directional laminates. It was found that the internal damage at each stage (matrix cracks, debonds in the weft, successive debonds in the warp and ‘metadelaminations’ between warps and wefts) occurred near the cross-over point of the fabric. The modulus decay mechanism was explained by considering the progression of this internal damage. From the end of the first stage to the beginning of the middle stage, a characteristic damage state (CDS) (called a ‘meta-CDS’) was observed. It was found that woven composites have a unit area of damage accumulation (called a ‘unit cell’) and the damage of each unit cell and its distribution control the total fatigue damage of the material.     

Analysis of an Electromagnetic Field Created by Line Current Using Constrained Interpolation Profile Method

Development of accurate schemes is a technical issue related to calculation of electromagnetic fields. This study uses constrained interpolation profile (CIP) method to analyze electromagnetic fields created by line current. This is a novel method proposed by Yabe. Comparison of results obtained using finite difference time domain (FDTD) analysis and CIP analysis indicates that CIP analysis provides higher accuracy using identical discretization. In addition, given the same level of accuracy, CIP analysis requires less memory and less calculation time     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Mortality of chromium plating workers in Japan--a 16-year follow-up study

Opportunistic infections are common and major causes of morbidity in patients with AIDS. Endemic mycoses pose serious risks for patients in certain parts of the world. Histoplasmosis occurs in 2-5% of patients with AIDS in the Ohio and Mississippi River valleys of the United States and in over 25% of patients from a few cities. Antigen testing has become a highly useful method for diagnosing histoplasmosis rapidly, evaluating the response to treatment and diagnosing relapse. Treatment with amphotericin B or itraconazole is effective (90% or higher) if the patient is not seriously ill at the time of diagnosis but the mortality approaches 50% for those with multiorgan failure. Itraconazole blood levels should be monitored and drugs that impair the absorption or accelerate the metabolism of itraconazole should be avoided. Prophylaxis with itraconazole may be appropriate in areas with an incidence of histoplasmosis. A recently completed study in cities which have unusually high rates of histoplasmosis will provide greater insight into the role of prophylactic antifungal therapy.