Effects of SO2 on selective catalytic reduction of NO with NH3 over a TiO2 photocatalyst

The effect of SO₂ gas was investigated on the activity of the photo-assisted selective catalytic reduction of nitrogen monoxide (NO) with ammonia (NH₃) over a TiO₂ photocatalyst in the presence of excess oxygen (photo-SCR). The introduction of SO₂ (300 ppm) greatly decreased the activity of the photo-SCR at 373 K. The increment of the reaction temperature enhanced the resistance to SO₂ gas, and at 553 K the conversion of NO was stable for at least 300 min of the reaction. X-ray diffraction, FTIR spectroscopy, thermogravimetry and differential thermal analysis, x-ray photoelectron spectroscopy (XPS), elemental analysis and N₂ adsorption measurement revealed that the ammonium sulfate species were generated after the reaction. There was a strong negative correlation between the deposition amount of the ammonium sulfate species and the specific surface area. Based on the above relationship, we concluded that the deposition of the ammonium sulfate species decreased the specific surface area by plugging the pore structure of the catalyst, and the decrease of the specific surface area resulted in the deactivation of the catalyst.     

Metastable phase relation and phase equilibria in the Cr2O3-Fe2O3 system

In order to ascertain the metastable phase relation in the Cr₂O₃-Fe₂O₃ system, the existing phases were investigated by X-ray analysis using samples obtained by heating the coprecipitated powders for 1 h at 600–1000°C. There was a metastable two-phase region of Cr₂O₃-rich (CC) and Fe₂O₃-rich (FC) phases below about 940°C. Equilibrium state of 1:1 composition at 600–900°C was considered to be a single phase of the corundum solid solution. The metastable two-phase CC + FC region was suggested to appear probably due to the compositional inhomogeneity in the coprecipitated powders.     

Cell-mediated immunological responses in cervical and vaginal cancer patients immunized with a lipidated epitope of human papillomavirus type 16 E7

Human papillomavirus (HPV) infection has been causally associated with cervical cancer. We tested the effectiveness of an HLA-A*0201-restricted, HPV-16 E7 lipopeptide vaccine in eliciting cellular immune responses in vivo in women with refractory cervical cancer. In a nonrandomized Phase I clinical trial, 12 women expressing the HLA-A2 allele with refractory cervical or vaginal cancer were vaccinated with four E786-93 lipopeptide inoculations at 3-week intervals. HLA-A2 subtyping was also performed, and HPV typing was assessed on tumor specimens. Induction of epitope-specific CD8+ T-lymphocyte (CTL) responses was analyzed using peripheral blood leukapheresis specimens obtained before and after vaccination. CTL specificity was measured by IFN-gamma release assay using HLA-A*0201 matched target cells. Clinical responses were assessed by physical examination and radiographic images. All HLA-A*0201 patients were able to mount a cellular immune response to a control peptide. E786-93-specific CTLs were elicited in 4 of 10 evaluable HLA-A*0201 subjects before vaccination, 5 of 7 evaluable HLA-A*0201 patients after two vaccinations, and 2 of 3 evaluable HLA-A*0201 cultures after all four inoculations. Two of three evaluable patients' CTLs converted from unreactive to reactive after administration of all four inoculations. There were no clinical responses or treatment toxicities. The ability to generate specific cellular immune responses is retained in patients with advanced cervical cancer. Vaccination with a lipidated HPV peptide epitope appears capable of safely augmenting CTL reactivity. Although enhancements of cellular immune responses are needed to achieve therapeutic utility in advanced cervical cancer, this approach might prove useful in treating preinvasive disease.     

Large Coulomb blockade oscillations at room temperature in ultranarrow wire channel MOSFETs formed by slight oxidation process

We propose a new fabrication technique of room-temperature operating silicon single-electron transistors (SETs). The devices are in the form of ultranarrow wire channel MOSFETs, where a sub-10-nm channel is formed by wet etching and slight thermal oxidation. Large Coulomb blockade (CB) oscillations whose peak-to-valley current ratio at room temperature is as high as 6.8 are observed in the fabricated ultranarrow wire channel MOSFETs. It is found that larger CB oscillations are obtained in the ultranarrow wire channel SETs than in the point-contact channel SETs. It is considered that the potential fluctuations induced during the channel formation processes give rise to multiple-dot SET structures in the ultranarrow wire channel MOSFETs.     

Influence of protein and lipid concentration of the test lubricant on the wear of ultra high molecular weight polyethylene

To gain a better understanding of the ultra-high molecular weight polyethylene (UHMWPE) wear mechanism in the physiological environment, the effects of protein and lipid constituents of synovial fluid on the specific wear rate of UHMWPE were examined experimentally. The multidirectional sliding pin-on-plate wear tester was employed to simulate the simplified sliding condition of hip joint prostheses. Bovine serum γ-globulin and synthetic l--DPPC were used as model protein and lipid constituents of synovia, respectively. Results of the wear test indicated that the UHMWPE wear rate primarily depended on the protein concentration of the test lubricant. Lipids acted as a boundary lubricant and reduced polyethylene wear in the low protein lubricants. However, the polyethylene wear rate increased with increasing lipid concentrations if the protein concentration was within the physiological level. Increased interactions between protein and lipid molecules and lipid diffusion to polyethylene surface might be responsible for the increased wear.     

Strengthening of Preloaded RC Beams Using Hybrid Carbon Sheets

Reinforced concrete (RC) beams subject to service loads of 40 or 60% of steel yielding were strengthened using hybrid continuous carbon fiber sheets. The hybrid systems were made of high-strength and high-modulus carbon sheets, and compared with systems using only high-strength carbon. It was found that the use of high-modulus carbon sheets in hybrid systems could increase the yielding load, the flexural stiffness, the postyielding ductility, and reduce the crack opening in concrete. The slope changes on load-deflection curves at steel yielding are not noticeable in hybrid systems. The tensile strains developed in hybrid sheets after the fracture of high-modulus carbon are higher in magnitude and distributed in a larger area, leading to an ultimate carbon fracture with concrete crushing. These unique features are attributed to the high stiffness and low ultimate tensile strain of the high-modulus carbon fibers which stiffen the structures, avoid or delay the fiber-reinforced polymer debonding, and facilitate the deformability during their subsequent breakdown.     

A growth control approach to Class II, Division 1 cases during puberty involving the simultaneous application of maxillary growth restriction and mandibular forward induction

A simple method that used headgear and a functional appliance simultaneously was used for the correction of Class II, Division 1 cases with severe denture base discrepancy. The treatment restricted the forward growth of the maxilla and advanced the mandible. The functional appliance, referred to as the mandibular growth advancer (MGA), advances the mandible progressively with a splint, with the objective of remodeling the condyle and the glenoid fossa in the temporomandibular joint. Functional adaptation was achieved as the muscles that are attached to the mandible adjusted to new positions. In the two cases that illustrate this method, the ANB angle decreased and the Ar-B distance increased over a short period to four and six times the mean Japanese growth rate, respectively. After the correction of the denture-base discrepancy, a multibracket fixed appliance was used for dental alignment, and good skeletal, occlusal relationships and profiles were obtained. Treatment of severe denture-base discrepancy in this manner may reduce the skeletal abnormality, decrease the number of extraction cases, and shorten the subsequent multibracket treatment time. And it may reduce the iatrogenic side effects caused by prolonged mechanotherapy with a fixed appliance.     

Binding of mutated Ras- and p53-derived peptides to HLA-DR molecules

We investigated retrospectively 132 cases of open wedge high tibial osteotomy using an external fixation device, concentrating on the rate of neurological complications. One group of patients underwent surgery according to the conventional technique (n = 89). The rate of transient neurological complications was 15.7%; 7 months after surgery the rate of persistent deficits was 12.4%. For the second group (n = 43) a modified surgical technique was used that lowered the complication rate significantly (transient deficits 14%, persistent deficits 4.7%). In the modified technique the osteotomy is not performed in the conventional way using an oscillating saw but through consecutive drill holes of increasing diameter followed by osteoclasis. The lower complication rate in the second group is mainly due to the less extensive approach that leads to a smaller number of postoperative tibialis anterior syndromes (type B lesion). No differences were found with type C lesions (extension deficit of D1). No complete peroneal nerve palsy (type A) occurred in either group. We conclude that the reduction of neurological complications in group 2 is related to the less extensive approach of the proposed technique.