Evaluation of Fracture Mechanisms in Al-Si Metal Matrix Nanocomposites Produced by Three Methods of Gravity Sand Casting,Squeeze Casting and Compo Casting in Semi-Solid State

Silicon - Magnetic stirring is considered to be the most useful stirring method in semi-solid casting processes which doesn’t have the restrictions of the mechanical stirring. In this...     

Remote sensing of salinity in the San Francisco Bay Delta

Salinity of the San Francisco Bay Delta has been studied for the past seven decades. There is a significant gradient in salinity within this estuarine system that influences the growth and distribution of phytoplankton as well as the abundance and migration of shrimp and fish population. Several government agencies which have jurisdictions over this area are attempting to gather extensive data for effectively monitoring of this estuary. Repetitive remotely sensed data acquired from Landsat may be considered by these agencies as having the potential to provide a cost-effective method for gathering and processing water quality related data. In this study, Landsat multispectral scanner (MSS) data and color and color infrared photographs acquired from a U-2 aircraft were combined with surface measurements for salinity mapping of the San Francisco Bay Delta. The salinity measurements and U-2 photography were obtained simultaneously and coincident with landsat overpass. A regression model was developed between the surface truth data and Landsat digital data for 29 preselected sample sites and was then extended to the entire study area. The results included a salinity map of the study area and the statistical summaries. The results were in general agreement with the reported distribution of salinity values in the literature for the same time of the year. Based on the results and the associated analyses of natural color and color infrared photographs and Landsat color composite imagery, it was concluded that: (1) it was virtually impossible, at least within this test site, to establish any quantitative judgement regarding the salinity values by visual interpretation of the imagery; and (2) the present study constitutes the first effort to successfully use Landsat digital data for salinity mapping, by means of digital processing, for this geographic area.     

Electrospray modeling of highly viscous and non‐Newtonian liquids

The electrohydrodynamic spraying of highly viscous and non‐Newtonian aqueous solutions of sodium alginate were experimentally modeled with high direct‐current electric fields. A prototype electrospray setup comprising a nozzle connected to a high‐voltage counter electrode connected to earth and a curing facility to solidify the droplets was used. The main aim was initially set to extend the knowledge of the electrospray to highly viscous liquids, where shear thinning was the main rheological feature of fluid flow through the nozzle of the spray system. To model the process, the effects on the size of beads of the electric field strength, nozzle diameter, flow rate, and the material properties of density, viscosity, surface tension, and electrical conductivity were characterized. The size distribution of the beads was obtained after the droplets were cured in a calcium chloride solution with an image analyzer system. The rheological study, carried out on different concentrations of alginate solution (i.e., 1–3 w/v %), showed a significant reduction in the viscosity as a function of the shear rate. Considering the shear‐thinning behavior of the solutions, in the modeling we applied the viscosity at the operational shear rate in the nozzle. Four dimensionless groups were introduced to obtain the relationship between the dimensionless group representing diameter and the other groups in the dripping and jet modes with statistical analysis of the experimental data. The proposed equations correlated the size of beads within ±10% deviations as compared to the experimental results. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Modeling of Estuarne Chlorophyll a from an Airborne Scanner

Near simultaneous collection of 34 surface water samples and airborne multispectral scanner data provided input for regression models developed to predict surface concentrations of estuarine chlorophyll a. Two wavelength ratios were employed in model development. The ratios werechosen to capitalize on the spectral characteristics of chlorophyll a, while minimizing atmospheric influences. Models were then applied to data previously acquired over the study area thre years earlier. Results are in the form of color-coded displays of predicted chlorophyll a concentrations and comparisons of the agreement among measured surface samples and predictions basedon coincident remotely sensed data. The influence of large variations in fresh-water inflow to the estuary are clearly apparent in the results. The synoptic view provided by remote sensing is another method of examining important estuarine dynamics difficult to observe from in situ sampling alone.     

A 2.4-GHz CMOS transceiver for Bluetooth

A fully integrated CMOS transceiver tuned to 2.4 GHz consumes 46 mA in receive mode and 47 mA in transmit mode from a 2.7-V supply. It includes all the receive and transmit building blocks, such as frequency synthesizer, voltage-controlled oscillator (VCO), power amplifier, and demodulator. The receiver uses a low-IF architecture for higher level of integration and lower power consumption. It achieves a sensitivity of -82 dBm at 0.1% BER, and a third-order input intercept point (IIP3) of -7 dBm. The direct-conversion transmitter delivers a GFSK modulated spectrum at a nominal output power of 4 dBm. The on-chip voltage controlled oscillator has a close-in phase-noise of -120 dBc/Hz at 3-MHz offset     

Experimental investigation of the effects of different chemical absorbents on wetting and morphology of poly(vinylidene fluoride) membrane

Membrane wetting is of one the most important factor that affects the CO₂ absorption efficiency in membrane contactors due to the increase of mass transfer resistance. In this study, the effects of different absorbents on the wettability of poly(vinylidene fluoride) membranes were investigated. Four absorbents including monoethanolamine, potassium carbonate–piperazine (PZ), potassium carbonate–monoethanolamine, and methyldiethanolamine–PZ were applied to investigate the effects of different absorbents on membrane wetting. Membrane properties before and after contact with absorbents were investigated using methods of thermogravimetric analysis, Fourier transform infrared spectroscopy, electron scanning microscope, and contact angle measurements. The results revealed that methyldiethanolamine and mixed absorbents containing methyldiethanolamine caused the most morphological changes in membrane. The results showed that reduction percentages of contact angle for water, K2CO3/PZ, K2CO3/MEA, MEA, and MDEA/PZ solutions were 14.52, 16.9, 21.19, 23.7, and 28.33, respectively, after 30 days immersion. The results also showed that potassium carbonate–PZ solution caused the least change in membrane wettability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45543.     

Longitudinal jerk and celeration as measures of safety in bus rapid transit drivers in Tehran

Abstract

Traditionally, analysis of individual differences in road traffic crash risk has relied on after the fact crash data. Nowadays with the help of technologies like GPS, new measures are developed to assess driving risk, inferred from naturalistic driving behaviour of drivers. In this study, two main ways of modelling driver behaviour in naturalistic driving research were discussed and compared to each other. For this purpose, 176 Bus Rapid Transit (BRT) drivers were investigated during their normal driving on Tehran BRT routes. Their speed was continuously recorded by a smart phone app from which was derived deceleration, jerk and celeration measures. Analysis showed that all of the proposed measures had positive correlations with culpable crashes and that one of the jerk variables yielded the highest correlation. Measurements of speed derivatives like jerk and celeration can help to identify dangerous driving styles in public transportation and reduce the number of crashes. Although the results of this study are encouraging, further studies for longer periods are needed to improve the reliability of the measures.     

A genetic algorithm for optimization problems with fuzzy relation constraints using max-product composition

We consider nonlinear optimization problems constrained by a system of fuzzy relation equations. The solution set of the fuzzy relation equations being nonconvex, in general, conventional nonlinear programming methods are not practical. Here, we propose a genetic algorithm with max-product composition to obtain a near optimal solution for convex or nonconvex solution set. Test problems are constructed to evaluate the performance of the proposed algorithm showing alternative solutions obtained by our proposed model.     

Combined method of complex coacervation and electrospray for encapsulate preparation

Encapsulate beads composed of alginate and chitosan as shell and bovine serum albumin (BSA) as core were prepared by combined method of complex coacervation and electrospray. The main objective of this work was to produce mono‐sized and spherical capsule of chitosan‐alginate with controlled sizes of capsules and shell. However, the effects of applied voltage, flow rate, and molecular weight of chitosan were investigated on the size, size distribution, membrane thickness of the prepared capsules, as well as the release rate of BSA. The results revealed that by the method developed in this study, it was possible to produce spherical capsules with controlled size and narrow size distribution. Increasing the voltage and decreasing the flow rate reduced the radius of capsule and its shell thickness from 2.09 mm to 750 μm and from 1.31 mm to 490 μm, respectively. Furthermore, the molecular weight of chitosan had no significant effect on the capsules' size and the release rate of BSA, whereas the rate of BSA release was increased with increase of the voltage. The later effect would be due to the increase of shell porosity at the higher voltages. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010