Sputter deposition technology as a materials engineering

Sputter deposition is currently being widely used in the microelectronics industry for the production of silicon integrated circuits. Recently interest has been focused on sputter deposition as a new materials processing technique. The highly energetic sputtered atoms enhance crystal growth and/or sintering during film growth. This results in lowering of the growth temperature of high temperature materials including cubic diamonds. Single crystals of complex ceramics materials could be prepared by sputter deposition through epitaxial growth process. Atomically controlled deposition using multi-target sputter enables to make man-made superlattice including high-T _C superconductors of layered perovskite. At present sputter deposition is one of key materials technologies for the coming century.     

Humidity Sensor Characteristics of Woodceramics

The humidity sensor characteristics of Woodceramics were investigated. The Woodceramics used in this experiment were prepared at 650–900°C. The size of specimens selected was 1 × 1 × 10 mm . One was used as-cut and the other was polished. Above 700°C, the resistance of the specimen was below 50 and the decrease of resistance with increasing relative humidity was small. The specimen prepared at 650°C had a resistance of about 1 k. The resistance of as-cut specimens decreased with increase in relative humidity, but that of the polished specimen did not change significantly. The difference between as-cut and polished samples was explained by the differences in surface micro-structure.     

Novel process for cover glass with ideal stress distribution

Abstract — This paper proposes a new process to manufacture cover glass that overcomes a strength trade‐off between the face and the edge. In the process, alkali barrier films are deposited on glass faces before an ion exchange process in order to control face stress properties without inhibiting the edge strengthening. As a demonstration of the process, alkali‐alumino‐silicate glass sheets with sputter‐deposited SiO₂ films were chemically strengthened, and then their stress properties and strengths were investigated. As a result, thicker SiO₂ films cause lower face DOL (depth of strengthened layer), and it is observed that the faces have lower DOL than the edges. In strength tests corresponding to major fracture modes of smartphone cover glass, specimens with 80–100 nm films have more balanced face performance and better edge impact strengths than the no‐film specimen.     

Control of three-link underactuated manipulators using a switching method of fuzzy energy regions

In general, manipulators used for industry and in academic laboratories have actuators to drive each joint. On the other hand, underactuated manipulators handled by our research have some passive or free joints without actuators and brakes. We recently developed a switching method of fuzzy energy regions to control such manipulators. In such a method, it is necessary to design parameters related to energy regions and the gains of some partly stable controllers based on the computed torque method. Here, the switching method is applied for a three-link underactuated manipulator. We optimize such design parameters related to fuzzy energy regions by a genetic algorithm. The effectiveness of the present method is illustrated with some simulations. This work was presented in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Modular fuzzy-neuro controller driven by spoken language commands.

We present a methodology of controlling machines using spoken language commands. The two major problems relating to the speech interfaces for machines, namely, the interpretation of words with fuzzy implications and the out-of-vocabulary (OOV) words in natural conversation, are investigated. The system proposed in this paper is designed to overcome the above two problems in controlling machines using spoken language commands. The present system consists of a hidden Markov model (HMM) based automatic speech recognizer (ASR), with a keyword spotting system to capture the machine sensitive words from the running utterances and a fuzzy-neural network (FNN) based controller to represent the words with fuzzy implications in spoken language commands. Significance of the words, i.e., the contextual meaning of the words according to the machine's current state, is introduced to the system to obtain more realistic output equivalent to users' desire. Modularity of the system is also considered to provide a generalization of the methodology for systems having heterogeneous functions without diminishing the performance of the system. The proposed system is experimentally tested by navigating a mobile robot in real time using spoken language commands.     

Voltage-balancing method for IGBTs connected in series

This paper presents a new method for balancing voltages of series-connected insulated gate bipolar transistors (IGBTs). This method can be implemented only by adding simple circuits to the gate drive system of the IGBTs, and its effect of balancing the IGBT's collector-emitter voltages during the switching transients is remarkable. This principal strategy and experimental results with series-connected IGBTs are first described. After that, further experimental results are shown from the switching tests of four 2.5-kV flat-packaged IGBTs connected in series. Through the switching tests, superior characteristics of the proposed method have been confirmed.     

An interval algorithm for finding all solutions of non‐linear resistive circuits

In this letter, an efficient algorithm is proposed for finding all solutions of non‐linear (not piecewise‐linear) resistive circuits. This algorithm is based on interval analysis, the dual simplex method, and the contraction methods. By numerical examples, it is shown that the proposed algorithm could find all solutions of systems of 500–700 non‐linear circuit equations in acceptable computation time. Copyright © 2004 John Wiley & Sons, Ltd.     

Low-Noise and High-Frequency Resolution Electrooptic Sensing of RF Near-Fields Using an External Optical Modulator

We developed an electrooptic (EO) sensing system using an external optical intensity modulator for radio frequency (RF) electric near-field measurements. This low-noise, high-frequency resolution system is based on the photonic heterodyning technique in which a RF near-field signal is mixed with modulated light by an EO crystal and downconverted to the difference frequency. Because the optical modulator has a bandwidth extending from DC to several gigahertz, the frequency resolution of this system is determined by that of the RF synthesizer it uses. The intensity noise of the modulated light is quite low, and the noise level of the EO signal can be reduced to almost the shot-noise level by using a balanced detection scheme.     

Optimal operation of cogeneration system coordinated by aggregator for providing the demand and supply regulation capacity

Recent growth of renewable energy generations with natural variability, such as photovoltaic generation and wind turbine generation, would make the demand and supply control in a whole power system more difficult, and therefore, alternatives for demand and supply regulation resources would be required. The authors focus on cogeneration system (CGS) as one of regulation resources. In order to procure adequate volume of regulation capability, an aggregator coordinates a number of CGSs efficiently and flexibly considering the wide variety of electricity/thermal demands of CGS owners. This paper proposes a novel optimal operation strategy of CGS coordinated by the aggregator considering the energy balance and operation cost of individual CGS owner. This paper also demonstrates the availability of CGSs for regulation capability by numerical case studies in which the actual consumption profile is employed.     

Synthesis and chemical properties of polyethyleneimines crosslinked by penta-2,4-dienylideneammonium unit

The reaction of N-(2,4-dinitrophenyl)pyridinium anion ( salt(A) ; A = Cl⁻, FeCl₄⁻, and (CN)₂N⁻) with linear polyethyleneimine (LPEI; M_n = 20 380) and branched polyethyleneimines (BPEI1; M_n = 600, BPEI2; M_n = 10 000) at various molar feed ratios without using a catalyst resulted in pyridinium ring opening to yield ionic LPEI and BPEIs that were crosslinked by conjugated penta-2,4-dienylideneammonium (PDA) units, LPEI-PDA , BPEI1-PDA , and BPEI2-PDA , respectively. A model compound was synthesized by the reaction of salt(Cl) with diethylamine. The solubilities of BPEI1-PDA and BPEI2-PDA depended on the feed ratios between salt(Cl) and BPEI1 or BPEI2. Dipping LPEI-PDA into water and methanol yielded hydro- and organogels, respectively. UV–vis and reflection measurements revealed an expanded π-conjugation length between the polymer chains due to the through-space orbital interaction of the electrons on the two nitrogen atoms at the crosslinked positions in LPEI-PDA , BPEI1-PDA , and BPEI2-PDA . Cyclic voltammetry analysis suggested that the polymers underwent electrochemical oxidation. Measurement using a superconducting quantum interference device (SQUID) indicated that LPEI-PDA having FeCl₄⁻ anions was paramagnetic. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48712.