Direct observation of the crystal-growth transition in undercooled silicon

Using an electromagnetic levitation facility with a laser heating unit, silicon droplets were highly undercooled in the containerless state. The crystal morphologies on the surface of the undercooled droplets during the solidification process and after solidification were recorded live by using a high-speed camera and were observed by scanning electron microscopy. The growth behavior of silicon was found to vary not only with the nucleation undercooling, but also with the time after nucleation. In the earlier stage of solidification, the silicon grew in lateral, intermediary, and continuous modes at low, medium, and high undercoolings, respectively. In the later stage of solidification, the growth of highly undercooled silicon can transform to the lateral mode from the nonlateral one. The transition time of the sample with 320 K of undercooling was about 535 ms after recalescence, which was much later than the time where recalescence was completed.     

Containerless solidification of highly undercooled mullite melts: Crystal growth behavior and microstructure formation

A mullite (3Al₂O₃·2SiO₂) sample has been levitated and undercooled in an aero-acoustic levitator, so as to investigate the solidification behavior in a containerless condition. Crystal-growth velocities are measured as a function of melt undercoolings, which increase slowly with melt undercoolings up to 380 K and then increase quickly when undercoolings exceed 400 K. In order to elucidate the crystal growth and solidification behavior, the relationship of melt viscosities as a function of melt undercoolings is established on the basis of the fact that molten mullite melts are fragile, from which the atomic diffusivity is calculated via the Einstein-Stokes equation. The interface kinetics is analyzed when considering atomic diffusivities. The crystal-growth velocity vs melt undercooling is calculated based on the classical rate theory. Interestingly, two different microstructures are observed; one exhibits a straight, faceted rod without any branching with melt undercoolings up to 400 K, and the other is a feathery faceted dendrite when undercoolings exceed 400 K. The formation of these morphologies is discussed, taking into account the contributions of constitutional and kinetic undercoolings at different bulk undercoolings.     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

A calibration method for the energy-integrating function in photovoltaic system monitoring

Solar radiation has an irregularly varying factor due to a basic day and night cycle and climatic conditions. For such conditions a data sampling interval is important to ensure the accuracy of energy monitoring in a photovoltaic system. While treating a system monitoring equipment as a black box. the author has developed the method of calibrating an energy-integrating function. At first for various input waveforms, the relationship between sampling intervals and quasi-integration outputs have been examined by trapezoidal rule. In the numerical simulation the phases of the sampling clock also are considered Then it is concluded that a sampling interval can be inspected through outside observation only by using a rectangular single pulse. By applying the pulse to the energy-integrating process, two kinds of integrated outputs can be obtained for different sampling phases. The calculated difference between both outputs can uniquely give the sampling interval being inspected. Conditions to ensure measuring accuracy are discussed and the validity of this method has been demonstrated experimentally. Practical calibrating procedures also are proposed for the integrating function of PV system monitoring.     

Spherical Yttrium Aluminum Garnet Embedded in a Glass Matrix

Containerless processing was used to investigate the glass-forming behavior of Al₂O₃–Y₂O₃ glass. The amorphous bulk samples were obtained at compositions with 25–37.5 mol% yttria when the melt was cooled at a cooling rate of ∼250 K/s. Although small spherical particles (∼10 μm) with the same composition of the matrix were detected in the amorphous samples with 32.5–37.5 mol% yttria, the microfocus X-ray diffraction result indicated that the small spherical particles were crystalline Y₃Al₅O₁₂ garnet (YAG), rather than being amorphous. This observation suggested that small YAG particles could not grow larger after their nucleation, because of the high viscosity at high undercooling and the high cooling rate, which would graze the nose of the continuous cooling temperature diagram of YAG.     

Electro-rheological effect and dynamic rheological properties of a blend composed of two liquid crystalline materials with different molecular weight

Electro-rheological (ER) effect of a blend composed of two liquid crystalline materials with different molecular weights is described in this article. The results indicated that ER effect of the blend was observed at the temperature range where each neat sample did not show ER effect. Furthermore, both storage modulus (G′) and loss modulus (G″) decreased drastically at the temperature range for the blend in dynamic viscoelastic measurements. We show that steady ER effect could be obtained by using a blend made up of two liquid crystalline components, whereas remarkable increment in shear stress was not observed for each component under applied electric field.     

A pre-heating vaporization technology of coal-water-slurry for the gasification process

A pre-heating vaporization technology of coal water slurry, CWS, was developed to increase the efficiency of coal gasification with the reduction of oxygen consumption. A CWS pre-heating experimental unit having a capacity of 2.0 tons-coal/day was manufactured. After the CWS was heated to 573 K at about 10 MPa, water in CWS was continuously vaporized in a tube of which the diameter increased gradually (2–10 mm I.D.), and dry coal particles with steam were atomized and fed to a vessel. No aggregation of coal particles was observed in the atomized samples. The temperature and the pressure distributions of the fluid were calculated with empirical heat transfer and pressure drop correlations. The calculated results well corresponded to the experimental data measured in some test points. Using the calculation model, a large scale apparatus of 100 tons-coal/day was designed using KNO₃ + NaNO₂ + NaNO₃ molten salt as a heating medium.     

Microstructure Control of Thermally Sprayed Co-Based Self-Fluxing Alloy Coatings by Diffusion Treatment

This article describes microstructure control aimed for wear-resistance improvement of Co-based (Co-Cr-W-B-Si) self-fluxing alloy coating by diffusion treatment. The diffusion treatments of thermally sprayed Co-based self-fluxing alloy coating on steel substrate were carried out at 1370-1450 K for 600-6000 s under an Ar gas atmosphere. Microstructural variations of the coating and the interface between the substrate and the coating were investigated in detail. A proper diffusion treatment precipitates two kinds of fine compounds in Co-based matrix. X-ray diffractometer (XRD) and electron probe microanalyzer (EPMA) analysis revealed these precipitates to be a chromium boride dissolving cobalt and a tungsten boride containing cobalt and chromium. The size of each precipitate became larger with increasing treatment temperature and time. A coating with the proper size borides showed a superior wear-resistance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Predicting viewer-perceived activity/dominance in soccer games with stick-breaking HMM using data from a fixed set of cameras

We attempted to predict activity/dominance for soccer games, where activity is defined as the degree of activity of the game as perceived by the viewer, whereas dominance is the degree at which the viewer perceives a particular team to dominate over the other team. Such activity/dominance information would help a layman viewer understand the game. It would also enable construction of an automatic digest creation system that extracts scenes having high activity/dominance. There are two facets of this study: 1. The main part of the underlying prediction model consists of a Stick-Breaking Hidden Markov Model, where the data automatically estimates the number of states of the Markov process behind the data. 2. The data used in this paper is vector time-series data consisting of player, referee, and ball positions, together with team information, acquired by a set of fixed cameras. The problem was approached with a Bayesian framework where learning and prediction were implemented by three different methods: Markov Chain Monte Carlo, Expectation Maximization, and Variational Bayes. The proposed method was tested using a dataset consisting of 10 professional soccer games and was compared against standard regression methods.