Effects of Neodymium Concentration on Optical Characteristics of Polycrystalline Nd:YAG Laser Materials

A neodymium-doped yttrium-aluminum garnet (Y₃A1₅O₁₂, YAG) (Nd:YAG) ceramic that contained 0.3–4.8 at.% neodymium additives and exhibited nearly the same optical properties as those of a single crystal was fabricated by a solid-state reaction method using high-purity powders. Although the integrated absorption intensity of the ²H_9/2+⁴F_5/2 bands simply increased as the neodymium concentration in the YAG ceramics decreased, the fluorescence intensity of the 2.4 at.% Nd:YAG ceramic was the strongest among Nd:YAG ceramics with various neodymium concentrations and a 0.9 at.% Nd:YAG single crystal. An oscillation experiment was performed on a continuous-wave (cw) laser with a diode-laser exciting system using those ceramics and the single crystal. The oscillation threshold and slope efficiency in that analysis were 309 mW and 28%, respectively, for the 1.1 at.% Nd:YAG ceramics and 356 mW and 40%, respectively, for the 2.4 at.% Nd:YAG ceramics. The lasing characteristics of the ceramics in the present work were superior to those of a 0.9 at.% Nd:YAG single crystal that was fabricated by the Czochralski (Cz) method.     

Stability,cure properties,and applicability as one part adhesives of systems of divalent metal salts of mono(hydroxyethyl) phthalate–anhydride–bisepoxide

Heterogeneous curable compositions of divalent metal salts of mono(hydroxyethyl) phthalate–anhydride–bisphenol A diglycidyl ether (BADG) systems were prepared by merely mixing these components at room temperature. Stability at room temperature and cure properties at high temperature of the compositions were investigated for evaluating their applicability as one part adhesive. It was found that the systems containing Mg were generally more stable than those containing Ca. Similarly, at 150°C the Ca-containing systems showed generally shorter gelation time than the Mg-containing ones, due to the fact that the Ca salt dissolves more rapidly and enters into the addition reaction with the anhydride, leading to the faster appearance of the catalytic activities of the Ca carboxylate group. Among the various combinations of components, the metal salt–succinic anhydride (SA)–BADG systems were stable at room temperature for more than 6 months and rapidly cured at high temperature, showing excellent adhesive properties. This result indicates that the SA-containing systems should be of interest in applications to one part adhesives.     

Sub-50-nm physical gate length CMOS technology and beyond usingsteep halo

Sub-50-nm CMOS devices are investigated using steep halo and shallow source/drain extensions. By using a high-ramp-rate spike annealing (HRR-SA) process and high-dose halo, 45-nm CMOS devices are fabricated with drive currents of 650 and 300 μA/μm for an off current of less than 10 nA/μm at 1.2 V with T_ox^inv =2.5 nm. For an off current less than 300 nA/μm, 33-nm pMOSFETs have a high drive current of 400 uA/μm. Short-channel effect and reverse short-channel effect are suppressed simultaneously by using the HRR-SA process to activate a source/drain extension (SDE) after forming a deep source/drain (S/D). This process sequence is defined as a reverse-order S/D (R-S/D) formation. By using this formation, 24-nm nMOSFETs are achieved with a high drive current of 800 μA/μm for an off current of less than 300 μA/μm at 1.2 V. This high drive current might be a result of a steep halo structure reducing the spreading resistance of source/drain extensions     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

A 3-V, 2%-mW multibit current-mode ΣΔ DAC with 100 dBdynamic range

The area ratio of analog to digital for mixed-mode chip has been inversely proportional to the process design rule for a given dynamic range objective, in contradiction to the LSI trend. This paper presents a design approach to realize a high degree of size reduction with process design rules for analog circuitry and a signal processing architecture for digital circuitry. A five-level current-mode ΣΔ digital-to-analog converter (DAC) system reveals full scale total harmonic: distortion plus noise (THD+N) of -90 dB and dynamic-range of 100 dB at 3 V (low power of 22 mW). Analog-area down-scaling can be accomplished by this architecture to be 1.09 mm², using 0.6-μm double-poly double-metal (DPDM) CMOS. For the digital filter, a pipeline instruction sequence with multiplierless architecture also gives small area of 1.98 mm²     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Calbindin-D 28 kD and parvalbumin in the horizontal cells of rat retina during development

Restless legs syndrome (RLS) and periodic limb movements in sleep (PLMS) are disorders that are common and disturbing to uremic patients. The treatment of these is problematic. Eight patients on chronic hemodialysis and continuous peritoneal dialysis completed a double-blind placebo-controlled crossover study using incremental doses of pergolide up to 0.25 mg at bedtime for treatment of RLS and sleep disruption. Five patients (62.5%) noted subjective improvement in restless legs symptoms and sleep quality. Objective results were improved only slightly by treatment. The percentage of the first hour in bed during which leg movements occurred decreased from 20.5 +/- 6.0 to 11.5 +/- 3.3, p < 0.05. However, findings during sleep were less positive. The following measures were not significant between placebo and treatment: leg movements per hour of sleep [53.7 +/- 22.3 vs 35.8 +/- 11.8 (p = 0.2)]; and percentage of sleep time spent with leg movements [5.5% +/- 3.2 vs 4.4% +/- 1.4 (p = 0.37)]. Patients continued to have very disrupted sleep, and we could not document an objective improvement in sleep architecture. Thus, although pergolide at the dose of 0.25 mg at bedtime provided subjective improvement in symptoms of restless legs and quality of sleep, and objectively decreased leg movements during the first hour in bed, objectively sleep continued to be disrupted. In this small patient group, the response to pergolide was not uniform, and further investigation is required to test effectiveness at higher doses.     

Co-crosslinking blend of incompatible polymers VI: Poly(vinyl chloride) toughened with polyethylene via a co-crosslinking technique

A binary blend which consists of two incompatible polymers such as poly(vinyl chloride) and polyethylene has been performed through a partial co-crosslinking reaction with peroxide to give a co-crosslinked blend with a uniform dispersion of small polyethylene particles and with an improved mechanical property. The results are obtained through the formation of a co-crosslinked product which acts as a potential solid phase dispersant as well as a well-bonded reinforcing interlayer on polyethylene particles uniformly dispersed in poly(vinyl chloride) matrix. The resulting blends (PVC/PE=10/90 wt) give carbon spherules of 0.5 to 1m diameter through pressure-carbonization at 650° C for 1 h.