Influence of Continuous Wave Interference on the Efficiency of the Non-Threshold Search Procedure for a Noise-Like Signal by Delay Time with Transition to the Frequency Domain

Journal of Communications Technology and Electronics - A statistical study of the effectiveness of the non-threshold search procedure for a noise-like phase-shift keyed signal by the delay time is...     

Analysis of the interference immunity during reception of ultrawideband chaotic signals in an indoor multipath propagation environment

The models of indoor multipath propagation of wideband and ultrawideband (UWB) signals are considered. Application of these models is recommended by an IEEE working group. In the framework of one of the models corresponding to the line-of-sight conditions, the algorithms for reception of UWB chaotic signals in the presence of reflection from multiple surfaces (echo signals) are proposed and analyzed. The efficiency of reception techniques is estimated from the viewpoint of the error probabilities. Limitations caused by the specific properties of echo signals are revealed, and the methods for improvement of reception quality are discussed.     

The giant dispersion of critical currents in a superconductor with fractal clusters of a normal phase

The influence of fractal clusters of a normal phase on the dynamics of a magnetic flux trapped in a percolation superconductor is considered. The critical depinning current distribution and the current-voltage characteristics of fractal superconducting structures in the resistive state are determined for an arbitrary fractal dimension of the cluster boundaries. The interval of fractal dimensions is found in which the dispersion of critical currents exhibits unlimited growth. It is established that the fractality of clusters favors a decrease of the electric field arising during the magnetic flux motion, thus increasing the critical current value. The region featuring the giant dispersion of critical currents can be expected to provide for the maximum current-carrying capacity of a superconductor.     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Taking into account the radiation pattern of a practical feed for a Luneberg lens

A method of taking into account the real feed radiation pattern for a Luneberg lens is proposed. According to this, the field of a feed with the given radiation pattern is expanded into series in spherical harmonics. Using this approach, it is possible to introduce the radiation patterns of real feeds into strict electrodynamic solution for a Luneberg lens, thus significantly refining a mathematical model of the antenna.     

Construction and verification of PLC-programs by LTL-specification

An approach to construction and verification of PLC-programs for discrete problems is proposed. For the specification of program behavior we use the linear-time temporal logic LTL. Programming is carried out in the ST-language according to an LTL-specification. The correctness analysis of an LTL-specification is carried out by the symbolic model checking tool Cadence SMV. A new approach to programming and verification of PLC-programs is shown by an example. For a discrete problem we give a ST-program, its LTL-specification and an SMV-model. The purpose of the article is to describe an approach to programming PLC, which would provide the possibility of PLC-program correctness analysis by the model checking method. Under the proposed approach the change of the value of each program variable is described by a pair of LTL-formulas. The first LTL-formula describes situations that increase the value of the corresponding variable, the second LTL-formula specifies conditions leading to a decrease of the variable value. The LTL-formulas (used for specification of the corresponding variable behavior) are constructive in the sense that they construct the PLC-program, which satisfies temporal properties expressed by these formulas. Thus, the programming of PLC is reduced to the construction of LTL-specification of the behavior of each program variable. In addition, an SMV-model of a PLC-program is constructed according to LTL-specification. Then, the SMV-model is analysed by the symbolic model checking tool Cadence SMV.     

An Experimental Investigation of the Multipath Propagation of Chaotic Radio Pulses in a Wireless Channel

Technical Physics Letters - An experimental investigation of the multipath propagation of ultrawideband (UWB) microwave chaotic radio pulses in a wireless channel has been carried out. Based on the...     

Wet Chemical Treatment and Mg Doping of p-InP Surfaces for Ohmic Low-Resistive Metal Contacts

Manufacturing a low-resistive Ohmic metal contact on p-type InP crystals for various applications is a challenge because of the Fermi-level pinning via surface defects and the diffusion of p-type doping atoms in InP. Development of wet-chemistry treatments and nanoscale control of p-doping for InP surfaces is crucial for decreasing the device resistivity losses and durability problems. Herein, a proper combination of HCl-based solution immersion, which directly provides an unusual wet chemical-induced InP(100)c(2 × 2) atomic structure, and low-temperature Mg-surface doping of the cleaned InP before Ni-film deposition is demonstrated to decrease the contact resistivity of Ni/p-InP by the factor of 10 approximately as compared to the lowest reference value without Mg. Deposition of the Mg intermediate layer on p-InP and postheating of Mg/p-InP at 350 °C, both performed in ultrahigh-vacuum (UHV) chamber, lead to intermixing of Mg and InP elements according to X-ray photoelectron spectroscopy. Introducing a small oxygen gas background (O₂ ≈ 10⁻⁶ mbar) in UHV chamber during the postheating of Mg/p-InP enhances the indium outdiffusion and provides the lowest contact resistivity. Quantum mechanical simulations indicate that the presence of InP native oxide or/and metal indium alloy at the interface increases In diffusion.     

On a reachability set of automation 3-counter machines

In this paper, we are concerned with the properties of a certain class of “automaton” counter machines in which each transition is defined nondeterministically according to the control states and irrespectively of the data being handled. Automaton counter machines are useful as a general means for demonstrating the undecidability of a series of problems that can be modeled by these machines, in particular, this being so for interacting coloring processes, which are useful in modeling the movement of data of various kinds between the components of a distributed system.     

Multirange multi-relaxation time Shan–Chen model with extended equilibrium

The work presents simulations with the multirange Shan–Chen model developed by Sbragaglia et al. (2007) [18], which improved the Shan–Chen model for the proper surface tension term. Also, by introducing the matrix collision operator and extended equilibrium density distribution function, the density ratio is increased from 100 to 160. The Multi-Relaxation Time (MRT) method attracted the attention of researchers due to several advantages, such as better stability, simulations with Prandtl number different from unity, and possibilities to improve the accuracy of the scheme compared with BGK Single Time Relaxation model. Our recent results have shown that the combination of MRT methods with multiphase flow models can improve the achievable gas–liquid density ratio.