A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

Soft X-ray image storage in poly (methylmethacrylate)

Images stored in resist for soft X-ray lithography or microradiography were found to show a background noise which limits the resolution. This is due to the statistically variable spatial distribution of the photons incident on the resist surface. An estimate of the fundamental noise-limited resolution has been made from the experimental measurement of photon flux incident on the surface and the accurate development rate curves. Monochromatic radiation from a synchrotron source was used.     

ATMPKs: a gene family of plant MAP kinases in Arabidopsis thaliana

We previously reported two cDNAs for MAP kinases (cATMPK1 and cATMPK2) from a dicot plant, Arabidopsis thaliana. We describe here the cloning and characterization of five additional cDNAs encoding novel MAP kinases in Arabidopsis, cATMPK3, cATMPK4, cATMPK5, cATMPK6, and cATMPK7. The amino acid residues corresponding to the sites of phosphorylation (Thr-Glu-Tyr) that are involved in the activation of animal MAP kinases are conserved in all the seven putative ATMPK proteins. Genes for MAP kinases in Arabidopsis constitute a family that contains more than seven members. Sequence analysis suggests that there are at least three subfamilies in the family of Arabidopsis genes for MAP kinases.     

90-nm process-variation adaptive embedded SRAM modules with power-line-floating write technique

The power consumption of a low-power system-on-a-chip (SoC) has a large impact on the battery life of mobile appliances. General SoCs have large on-chip SRAMs, which consume a large proportion of the whole LSI power. To achieve a low-power SoC, we have developed embedded SRAM modules, which use some low-power SRAM techniques. One technique involves expanding the write margin; another is a power-line-floating write technique, which enables low-voltage write operation. The power-line-floating write technique makes it possible to lower the minimum operating supply voltage by 100 mV. The other techniques involve using a process-variation-adaptive write replica circuit and reducing leakage current. These techniques reduce active power during write operations by 18% and reduce active leakage of the word-line driver by 64%. The prototype SRAM modules achieve 0.8-V operation, and a 512-kb SRAM module achieves 48.4-/spl mu/A active leakage and 7.8-/spl mu/A standby leakage with worst-leakage devices.     

Air bubbles in the subclavian or internal jugular veins: a common finding on contrast-enhanced CT

BACKGROUND: Foot complications in diabetes incur huge human and medical costs. There is a high incidence of complicated diabetes mellitus in Far North Queensland, particularly in the indigenous communities. METHODS: An audit of 51 patients admitted to Cairns Base Hospital from July 1992 to December 1994 with diabetic foot complications requiring surgical intervention was performed. RESULTS: The majority of surgical procedures were for serious infections in neuropathic feet precipitated by minor trauma. Surgical procedures included debridement/drainage, minor amputation, major amputation and arterial bypass. Half of the patients required more than one procedure and/or multiple admissions. Average length of stay was 48 days. Indigenous patients were overrepresented in this audited group. CONCLUSIONS: Prevention or minimization of diabetic foot complications can be achieved only through improvement in education and vigilance at all levels of the treatment process from community to hospital. Special attention to the needs of indigenous communities with a high incidence of diabetes must be a feature of any future initiatives.     

Effect of Silicon Dioxide on the Thermal Diffusivity of Aluminum Nitride Ceramics

The thermal diffusivity of AlN ceramics was significantly decreased by the addition of SiO₂. The AlN ceramics with 4 wt% SiO₂ could not be densified by pressureless sintering in the temperature range 1400° to 1800°C. The thermal diffusivity of these samples was very low because of their porous structure. The AlN ceramics containing 2, 4, and 8 wt% SiO₂ were densified by hot-pressing and also had low thermal diffusivity. In these samples, the grains of the 27R polytype that resulted from the reaction between AlN and SiO₂ were dispersed, obstructing the conduction of heat. The relation between the amount of 27R polytype and the thermal diffusivity of the AlN ceramics was determined.     

Interfacial tension of demixed polymer solutions near the critical temperature: polystyrene + methylcyclohexane

Interfacial tension between demixed solutions of polystyrene + methylcyclohexane has been measured near the critical temperature as a function of temperature using polystyrenes with molecular weights 9000 ～ 1.26 × 10⁶. The critical exponent for the interfacial tension was determined to be about 1.30 for the lower molecular weight systems. However, for higher molecular weights the exponent could not be obtained because the system departed from critical behaviour. Magnitudes of the interfacial tension were proportional to about N^?0.44, where N is the polymerization index. Experimental results were compared with the recently-proposed theories and found to be in qualitative agreement. The tricritical theory of polymer solutions was also compared with the experimental results.     

Thermal management of edge‐lit wide color gamut backlight for LCD using red laser diodes and cyan LEDs

The color gamut is one of the critical parameters that dictate the image quality of displays. The liquid crystal displays using white color light‐emitting diodes (LEDs) as the backlight, though having been widely employed recently, are not very satisfactory in terms of their color gamut because of the broad spectrum inherent to white LEDs. This prompted the authors to develop improved liquid crystal displays using an edge‐lit wide color gamut backlight that used red laser diodes and cyan LEDs. Generating laser beams with high color purity, the laser diodes are light sources with a significant effect on expanding the color gamut. However, laser diodes, red ones in particular, have unfavorable thermal characteristics. To cope with this shortcoming, the authors clearly defined the restrictive criteria for laying out two kinds of light source on the edge‐lit backlight and made a prototype 55‐type laser backlight for performance evaluation.     

Correction of color information of a 3D model using a range intensity image

Most active optical range sensors record, simultaneously with the range image, the amount of light reflected at each measured surface location: this information forms what is called a range intensity image, also known as a reflectance image. This paper proposes a method that uses this type of image for the correction of the color information of a textured 3D model. This color information is usually obtained from color images acquired using a digital camera. The lighting condition for the color images are usually not controlled, thus this color information may not be accurate. On the other hand, the illumination condition for the range intensity image is known since it is obtained from a controlled lighting and observation configuration, as required for the purpose of active optical range measurement. The paper describes a method for combining the two sources of information, towards the goal of compensating for a reference range intensity image is first obtained by considering factors such as sensor properties, or distance and relative surface orientation of the measured surface. The color image of the corresponding surface portion is then corrected using this reference range intensity image. A B-spline interpolation technique is applied to reduce the noise of range intensity images. Finally, a method for the estimation of the illumination color is applied to compensate for the light source color. Experiments show the effectiveness of the correction method using range intensity images.     

Current dependence of performance of TES microcalorimeters and characteristics of excess noise

We are developing transition edge sensor (TES) microcalorimeter arrays for future Japanese astronomy missions. Although 6.6 eV energy resolution for 5.9 keV and 74 μs decay time are achieved, our energy resolution was limited by the excess noise of unknown origin. The dominant noise showed 1/R dependence and it only appeared when the current through the TES, I, is larger than 10 μA. This is explained if we assume a constant voltage noise source with a level of 2(4kT_CR_n)^1/2. We also investigated the influence of I on the TES performance and found the TES sensitivity is reduced when the ratio of current to the critical current I/I_C is large. It can explain the reduction of observed when operated without a magnetic shield. We also found a strong correlation between I_C and or the baseline width. Thus, we conclude that I_C is an essential parameter for the TES performance.