A comparison of emulsifiers for the formation of oil-in-water emulsions: stability of the emulsions within 9 h after production and MR signal properties

Objective

To provide a basis for the selection of suitable emulsifiers in oil-in-water emulsions used as tissue analogs for MRI experiments. Three different emulsifiers were investigated with regard to their ability to stabilize tissue-like oil-in-water emulsions. Furthermore, MR signal properties of the emulsifiers themselves and influences on relaxation times and ADC values of the aqueous phase were investigated.

Materials and methods

Polysorbate 60, sodium dodecyl sulfate (SDS) and soy lecithin were used as emulsifiers. MR characteristics of emulsifiers were assessed in aqueous solutions and their function as a stabilizer was examined in oil-in-water emulsions of varying fat content (10, 20, 30, 40, 50%). Stability and homogeneity of the oil-in-water emulsions were evaluated with a delay of 3 h and 9 h after preparation using T₁ mapping and visual control. Signal properties of the emulsifiers were investigated by ¹H-MRS in aqueous emulsifier solutions. Relaxometry and diffusion weighted MRI (DWI) were performed to investigate the effect of various emulsifier concentrations on relaxation times (T₁ and T₂) and ADC values of aqueous solutions.

Results

Emulsions stabilized by polysorbate 60 or soy lecithin were stable and homogeneous across all tested fat fractions. In contrast, emulsions with SDS showed a significantly lower stability and homogeneity. Recorded T₁ maps revealed marked creaming of oil droplets in almost all of the emulsions with SDS. The spectral analysis showed several additional signals for polysorbate and SDS. However, lecithin remained invisible in ¹H-MRS. Relaxometry and DWI revealed different influences of the emulsifiers on water: Polysorbate and SDS showed only minor effects on relaxation times and ADC values of aqueous solutions, whereas lecithin showed a strong decrease in both relaxation times (r_1,lecithin = 0.11 wt.%⁻¹ s⁻¹, r_2,lecithin = 0.57 wt.%⁻¹ s⁻¹) and ADC value (Δ(ADC)_lecithin =  − 0.18 × 10^–3 mm²/s⋅wt.%) with increasing concentration.

Conclusion

Lecithin is suggested as the preferred emulsifier of oil-in-water emulsions in MRI as it shows a high stabilizing ability and remains invisible in MRI experiments. In addition, lecithin is suitable as an alternative means of adjusting relaxation times and ADC values of water.

     

Real-time organic aerosol chemical speciation in the indoor environment using extractive electrospray ionization mass spectrometry

Understanding the sources and composition of organic aerosol (OA) in indoor environments requires rapid measurements, since many emissions and processes have short timescales. However, real-time molecular-level OA measurements have not been reported indoors. Here, we present quantitative measurements, at a time resolution of five seconds, of molecular ions corresponding to diverse aerosol-phase species, by applying extractive electrospray ionization mass spectrometry (EESI-MS) to indoor air analysis for the first time, as part of the highly instrumented HOMEChem field study. We demonstrate how the complex spectra of EESI-MS are screened in order to extract chemical information and investigate the possibility of interference from gas-phase semivolatile species. During experiments that simulated the Thanksgiving US holiday meal preparation, EESI-MS quantified multiple species, including fatty acids, carbohydrates, siloxanes, and phthalates. Intercomparisons with Aerosol Mass Spectrometer (AMS) and Scanning Mobility Particle Sizer suggest that EESI-MS quantified a large fraction of OA. Comparisons with FIGAERO-CIMS shows similar signal levels and good correlation, with a range of 100 for the relative sensitivities. Comparisons with SV-TAG for phthalates and with SV-TAG and AMS for total siloxanes also show strong correlation. EESI-MS observations can be used with gas-phase measurements to identify co-emitted gas- and aerosol-phase species, and this is demonstrated using complementary gas-phase PTR-MS observations.     

Neurocontrol for lateral vehicle guidance

A solution to autonomous lateral vehicle guidance using a neurocontroller that can learn from measured human-driving data without knowledge of the physical car parameters is discussed. Simulations and practical tests confirm that a small-size feedforward autonomous neural network (21 neurons) can learn to steer a vehicle at high speeds only from looking at human-driving examples. In this way, the network learns the total closed-loop behavior, including the nonlinear dynamics of the vehicle and the driver's individual driving style. The main result of practical investigations is that the neutral controller trained on human-driving examples exhibits an aperiodic behavior that does not vanish at higher speeds (tests performed up to 130 km/h) and produces fewer lateral deviations than the linear state controller     

Small thermophotovoltaic prototype systems

In an earlier paper we reported on a small grid-connected thermophotovoltaic (TPV) system consisting of an ytterbia mantle emitter and silicon solar cells with 16% efficiency (under solar irradiance in standard test conditions, STCs). The emitter was heated up using a butane burner with a rated thermal power of 1.35 kW (referring to the lower heating value). This system produced an electrical output of 15 W, which corresponds to a thermal to electric (direct current) conversion efficiency of 1.1%. In the interim, further progress has been made, and significantly higher efficiencies have been achieved. The most important development steps are: (1) the infrared radiation-absorbing water filter between emitter and silicon cells (to protect the cells against overheating and against contact with flue gasses) has been replaced by a suitable glass tube. By doing this, it has been possible to prevent losses of convertible radiation in water. (2) Cell cooling has been significantly improved, in order to reduce cell temperature, and therefore increase conversion efficiency. (3) The shape of the emitter has been changed from spherical to a quasi-cylindrical geometry, in order to obtain a more homogeneous irradiation of the cells. (4) The metallic burner tube, on which the ytterbia emitter was fixed in the initial prototypes, has been replaced by a heat-resistant metallic rod, carrying ceramic discs as emitter holders. This has prevented the oxidation and clogging of the perforated burner tube. (5) Larger reflectors have been used to reduce losses in useful infrared radiation. (6) Smaller cells have been used, to reduce electrical series resistance losses. Applying all these improvements to the basic 1.35 kW prototype, we attained a system efficiency of 1.5%. By using preheated air for combustion (at approximately 370 °C), 1.8% was achieved. In a subsequent step, a photocell generator was constructed, consisting of high-efficiency silicon cells (21% STC efficiency). In this generator, the spaces between the cells were minimized, in order to achieve as high an active cell area as possible, while simultaneously reducing radiation losses. This new system has produced an electrical output of 48 W, corresponding to a system efficiency of 2.4%. This is the highest-ever-reported value in a silicon-cell-based TPV system using ytterbia mantle emitters. An efficiency of 2.8% was achieved by using preheated air (at approximately 500 °C). An electronic control unit (fabricated of components with low power consumption, and including a battery store) was developed, in order to make the TPV system self-powered. This unit controls the magnetic gas supply valve between gas supply cylinder and burner as well as the high-voltage ignition electrodes. Both the control unit’s own power consumption and the battery-charging power are supplied directly by the TPV generator. A small commercial inverter is used to transfer excess power to the 230 V grid.     

Crystallization of Polymer-Derived Silicon Carbonitride at 1873 K under Nitrogen Overpressure

The chemical stability of an amorphous silicon carbonitride ceramic, having the composition 0.57SiC·0.43Si₃N₄·0.49C is studied as a function of nitrogen overpressure at 1873 K. The ceramic suffers a weight loss at p _N2 < 3.5 bar (1 bar = 100 kPa), does not show a weight change from 3.5 to 11 bar, and gains weight above 11 bar. The structure of the ceramic changes with pressure: it is crystalline from 1 to 6 bar, amorphous at ∼10 bar, and is crystalline above ∼10 bar. The weight-loss transition, at 3.5 bar, is in excellent agreement with the prediction from thermodynamic analysis when the activities of carbon, SiC, and Si₃N₄ are set equal to those of the crystalline forms; this implies that the material crystallizes before decomposition. The amorphous to crystalline transition that occurs at ∼10 bar, and which is accompanied by weight gain, is likely to have taken place by a different mechanism. A nucleation and growth reaction with the atmospheric nitrogen is proposed as the likely mechanism. The supersaturation required to nucleate α-Si₃N₄ crystals is calculated to be 30 kJ/mol.     

Pretreatment and physical activation of acetylene cokes

Pretreatment of acetylene cokes at 450 °C with a mixture of nitrogen, oxygen and water vapour creates a relatively large surface area and some initial microporosity, further developed by water activation at 800 °C. For the same degree of burn-off, but without pretreatment, large micropores (L > 2–3 nm) are obtained and the external surface area remains small.     

Analysis of lipid classes by solid-phase extraction and high-performance size-exclusion chromatography

An improved method to analyze lipid classes of edible oils and fats by solid-phase extraction (SPE) and high-performance size-exclusion chromatography (HPSEC) is presented. A mixture of lipid standards was fractionated by the solid-phase extraction procedure (NH₂ phase) into polar and nonpolar fractions; these were then submitted to analysis by HPSEC. The size-exclusion chromatographic columns were three styrene/divinylbenzene columns with pore sizes of 100 Å and 50 Å. Light-scattering was used for the detection system, and the parameters of the detector were optimized to minimize the difference between the responses of the compounds studied. With this procedure it was possible to separate the following lipid classes: triacylglycerols, diacylglycerols, monoacylglycerols and free fatty acids, sterols, sterol esters, tocopherols and carotenoids. Quantitative analysis was studied for a light-scattering detector with several lipid standards of different molecular weights and unsaturation levels.     

Initial Stages in the Metal-dusting Process on Alloy 800

The initial stages of the metal-dusting process on Alloy 800 at 620 °C were investigated by light optical microscopy, RAMAN spectroscopy, atomic-force microscopy, Auger electron spectroscopy, transmission-electron microscopy and electron back-scatter diffraction. As it turned out the incubation period for metal-dusting is characterized by simultaneous formation of a heterogeneously growing oxide scale and deposition of carbon. The material surface shows different tarnish colors depending on the substrate-grain orientation with different susceptibility to the beginning of metal-dusting attack. “Low-index” grains were not attacked within the times investigated while the other grain orientations showed pitting. Carbon is evidently incorporated into the oxide scale from the very beginning of exposure with different intensities depending on the underlying substrate-grain orientation leading to differences in the tarnish colors. As a consequence carbides are formed even underneath “dense” oxide layers. Evidently metal-dusting attack starts at positions of the oxide scale where “higher carbon concentrations” are present.     

Effects of brefeldin-A on Golgi morphology in human cultured fibroblasts observed in three-dimensional stereo scanning electron microscopy

Brefeldin A (BFA) has been reported to cause disassembly of the Golgi. We have used three-dimensional (3-D) high-resolution scanning electron microscopy (HRSEM) to investigate these effects in human skin fibroblast cells. The spontaneous reassembly during prolonged exposure to BFA and some effects of forskolin were observed. A BFA concentration of 5μg/ml caused Golgi complexes to become vesicular, resulting in a progressive decrease in the size of the Golgi. Morphologic changes were visible within 2 min of BFA incubation, and by 30 min no identifiable Golgi could be found. Spontaneous reassembly of the Golgi apparatus upon the removal of the BFA or with continued long-term exposure with BFA could not be confirmed. Preliminary experiments with forskolin were not effective in reversing or inhibiting the effects of BFA in human fibroblast cells grown in culture. This inability for spontaneous reassembly and nonreversal by forskolin may reflect a differential effect of BFA in various cell types. HRSEM has proven to be useful for observing 3-D morphologic effects of BFA in Golgi.