Sandwiches and milk with varying fat and sodium contents: What is the best combination?

Saltiness and fattiness were systematically varied in combinations of wheat bread (unsalted vs regular-salt), spread (none vs regular-salt and regular-fat), cheese (low-salt and low-fat vs low-fat). All possible combinations, amounting to sixteen samples of sandwich and milk, were presented to 43 subjects for ratings of pleasantness. The subjects also rated the pleasantness of individual components. The unsalted bread without spread but with low-salt, low-fat cheese and any of the milk types received the lowest hedonic ratings, whereas the regular-salt bread with spread and with any of the cheese and milk options received the highest. The pleasantness of individual components predicted the pleasantness of a combination by only 10–40% (multiple regression analysis). Thus the pleasantness of an entity depended on the pleasantness of components only to a very limited extent. The absence of major elements, such as spread on bread or the salty taste in bread, had major effects on acceptance.     

Calculation of sliding power loss in spur gear contacts

An engineering-level calculation model for sliding power loss in spur gear contacts is presented. Teeth contact through the line of action is modelled as a constantly changing roller contact whose radius, speed, and load can be calculated from the gear geometry under the given operating conditions. The gear mesh cycle is approximated by a large number of elastohydrodynamic contacts. A constant film thickness and a Hertzian pressure distribution are assumed in each contact. The model includes non-Newtonian lubricant behaviour together with temperature and mixed lubrication effects in contact. The numerical solver is reasonably fast in evaluating effectively the sliding power loss dependence on the essential gear and lubricant parameters. The features and behaviour trends of the calculated sliding power losses have a close similarity with published results obtained from measurements and experiment-based power loss models with mineral oil. The limiting shear stress of the lubricant is observed to have an essential role in the power loss behaviour especially at high loads.     

Modeling of helical gear contact with tooth deflection

The majority of gear tribological studies are made on spur gears. However, helical gears are generally used in industry, and their contact behavior deserves more attention to establish a realistic base for detailed friction, wear and life studies. This study focuses on the modeling of helical gear contact with tooth deflection. A calculation model for helical gear contact analysis is introduced. Helical gear surface profiles are constructed from gear tool geometry by simulating the hobbing process. The model uses three-dimensional finite elements for the calculation of tooth deflection including tooth bending, shearing and tooth foundation flexibility. The model combines contact analysis with structural analysis to avoid large meshes. Tooth foundation flexibility was found to have an essential role in contact load sharing between the meshing teeth, whereas contact flexibility plays only a minor role. The capability of different local contact calculation methods was also studied.     

Experimental evaluation of friction between contacting discs for the simulation of gear contact

Instant gear contact can be simulated with contacting discs, which provides steady operating conditions and eliminates most of the dynamics and manufacturing tolerances involved in real gears, resulting in an accurately controlled contact condition. A high-pressure twin-disc test device was developed, where loading and rolling velocity can be varied continuously. It is equipped with disc bulk temperature, mean contact resistance and friction moment measurements. The test discs were grinded transversal to the disc rolling direction with proper crowning corresponding to the real gear flank properties. The test device was applied by studying the friction behaviour against the slide-to-roll ratio at different contact pressures, rolling velocities and surface roughness. The measurements were performed using mineral base oil in the range of operation conditions often used in industrial gears. In general, the measured friction coefficient behaviour correlates with earlier published results and is logical with measured bulk temperature and mean contact resistance. The limiting shear stress of the lubricant has an essential role in friction behaviour. Copyright © 2006 John Wiley & Sons, Ltd.     

Modelling and evaluation of the fretting fatigue cracking risk in smooth spherical contacts

A numerical model for the calculation of fretting fatigue crack initiation is presented and compared with experiments. The model is focused on smooth sphere-on-plane contact in partial and gross slip conditions. It is based on Hamilton’s explicit stress equations and the multi-axial Dang Van and Findley fatigue criteria enhanced with a statistical size factor concept. Promising correlation was found between the model and the experimental results with quenched and tempered steel 34CrNiMo6. The model assumptions, limitations and general application are also discussed.     

Assessing the quality of the sampling of fuel peat using computer simulation

A simulation scheme to assess and improve the performance of the sampling of fuel peat is considered. The scheme provides a practical possibility to inspect all possible sources of variation and error. Test results from a district heating plant are reported.     

A 2-level anisotropic electronic system in superfluid 4He

No Heading Theory for treating a two-level electronic system in superfluid helium is described. Numerical density functional theory calculations in 3-D are then used to calculate electronic absorption spectra for both spherical and angularly anisotropic chromophores. The results can be used in rationalizing the experimentally observed absorption spectra in small helium droplets. It is shown that anisotropic with the liquid does not lead to considerable changes in the linear absorption spectrum when compared to a purely spherical case.PACS numbers: 33.20 Kf, 33.70 Jg     

Development of a test device for the evaluation of fretting in point contact

Fretting wear and fatigue may occur between any two contacting surfaces, wherever short‐amplitude reciprocating sliding is present for a large number of cycles. A test device has been developed for the evaluation of fretting fatigue and wear in partial and gross slip conditions. Three similar sphere‐on‐plane contacts run at the same time. Normal force, tangential force or displacement amplitude and constant bulk stress can be controlled and measured separately. Reciprocating tangential displacement is produced with rotational motion, the amplitude and frequency of which can be adjusted and controlled accurately by an electric shaker. The number of load cycles for crack initiation and growth is determined with strain‐gauge measurements near the fretting point of contact. The contact surfaces are measured with 3D optical profilometer before fretting measurements to determine actual contact geometry. The measurements were done with quenched and tempered steel. The initial results indicate that cracks are mostly formed in partial slip conditions, whereas fretting wear is more heavily involved in gross slip conditions. The initiation of a crack occurs near the edge of the contact in the slip direction, where the calculated cracking risk has its maximum value in partial slip conditions. The number of cracks increases as the displacement amplitude, i.e. friction force, increases in partial slip conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Expression of two Trichoderma reesei endoglucanases in the yeast Saccharomyces cerevisiae

The cDNA copies of the two endo-beta-1,4-glucanase genes, egl1 and egl3, from the filamentous fungus Trichoderma reesei were expressed in yeast Saccharomyces cerevisiae under the control of the yeast phosphoglycerate kinase gene promoter. Active EGI and EGIII enzyme was produced and secreted by yeast into the growth medium. The recombinant EGI enzyme was larger and more heterogeneous in size than the native enzyme secreted by Trichoderma, due to differences in the extent of N-glycosylation between these two organisms. The morphology of the yeast cells producing EGI or EGIII was clearly different from control strain.     

Characterization of the genes of the 2,3-butanediol operons from Klebsiella terrigena and Enterobacter aerogenes

The genes involved in the 2,3-butanediol pathway coding for alpha-acetolactate decarboxylase, alpha-acetolactate synthase (alpha-ALS), and acetoin (diacetyl) reductase were isolated from Klebsiella terrigena and shown to be located in one operon. This operon was also shown to exist in Enterobacter aerogenes. The budA gene, coding for alpha-acetolactate decarboxylase, gives in both organisms a protein of 259 amino acids. The amino acid similarity between these proteins is 87%. The K. terrigena genes budB and budC, coding for alpha-ALS and acetoin reductase, respectively, were sequenced. The 559-amino-acid-long alpha-ALS enzyme shows similarities to the large subunits of the Escherichia coli anabolic alpha-ALS enzymes encoded by the genes ilvB, ilvG, and ilvI. The K. terrigena alpha-ALS is also shown to complement an anabolic alpha-ALS-deficient E. coli strain for valine synthesis. The 243-amino-acid-long acetoin reductase has the consensus amino acid sequence for the insect-type alcohol dehydrogenase/ribitol dehydrogenase family and has extensive similarities with the N-terminal and internal regions of three known dehydrogenases and one oxidoreductase.