Circulation rates of boiling liquids in a vertical tube

An experimental study of heat transfer to boiling liquids under natural convective flow has been carried out in a single tube vertical thermosiphon reboiler to investigate the effect of heat flux and submergence on circulation rates. The test liquids used were distilled water, various concentrations of propan-2-ol in water and their azeotrope. The test section was an electrically heated stainless steel tube of 25.56 mm i.d., 28.85 mm o.d. and 1900 mm long with twenty-one spot welded copper constantan thermocouples to measure the variations in wall temperature along its axis. The uniform heat fluxes in the range of 3.5–42.4 kW/m² were employed while inlet liquid sub-cooling varied from 0.2 to 30.7 °C. The liquid submergence levels were maintained in the range 30–100%. The typical experimental data has been graphically presented and discussed. An empirical correlation has been developed from the experimental data of the present study through regression analysis.     

Kinetics of oxygen absorption in aqueous sodium dithionite solutions

The absorption and reaction of oxygen in aqueous alkaline solutions of sodium dithionite has been experimentally investigated in a novel gas-liquid contactor. The novel gas-lift bubble column contactor was used to study the kinetics over wide ranges of reactant concentrations, temperature, and pH. The oxygen-sodium dithionite reaction was found to be first-order with respect to dithionite in the range of dithionite concentration < 0.1 M, and second-order in the range of dithionite concentration > 0.1 M. The reaction with respect to oxygen was found to be zero-order for all dithionite concentrations. These results and experimental investigations of the effect of solution alkalinity and temperature on the reaction rate are consistent with previous findings obtained in different gas-liquid contactors. The results thus confirm the feasibility of using the gas-lift bubble column for the kinetics of gas-liquid reactions.     

A New Method for Identifying Osmotically Limited and Gel Layer Controlled Pressure Independent Flux in Ultrafiltration

An unequivocal determination of whether pressure independent flux regime is osmotically controlled or gel layer dominated, is still open for discussion in the membrane literature. The present work reports a method that could be used to address this issue. It is shown that analysis of post steady state transient filtration data leads to clear demarcation of osmotically limited and gel layer controlled filtration. The method proposed in this work can also be used to estimate the additional filtration resistance offered by the polarization layer to the permeate flow in macromolecular ultrafiltration and has been verified experimentally. It has also been shown that the polarization layer thickness is not sensitive to the feed pressure but varies as a function of the bulk solute concentration; higher the bulk concentration, thicker is the polarization layer.     

A comprehensive study on co2-interphase mass transfer in vertical cocurrent and countercurrent gas-liquid flow

Cocurrent and countercurrent absorption and desorption of CO₂ in water was investigated in tall bubble columns (length 440 and 720 cm, diameter 15 and 20 cm, respectively). Operating conditions were applied which provided for high interphase mass transfer rates. Under these circumstances the relative gas holdup varies considerably with axial position whereas the mean bubble diameter measured at two points was found to be approximately constant. The measured data permit the calculation of local values of interfacial areas, superficial gas velocities, and frequency factors for bubble coalescence and break up. A dispersion model which takes into account the hydrostatic head and a variable gas velocity was applied to describe the measured concentration profiles in both phases. If increased mass transfer coefficients at the column bottom and measured local values of the hold up were used a striking agreement between experimental and predicted profiles could be obtained. The findings lead to a more sophisticated picture of the complex behaviour of gas-liquid dispersions at high interphase mass transfer rates.     

Admission control mechanism and performance analysis based on stochastic automata networks formalism

IEEE 802.16 has been designed to support QoS (Quality of Service) in Wireless broadband Metropolitan Networks (WMAN), and specifically in the access networks. To achieve this, the IEEE 802.16.e amendment introduces the service differentiation by five service classes (UGS, ertPS, rtPS, nrtPS and BE). To maintain the QoS of active connections and to avoid any congestion in the network, an Admission Control (AC) is defined. AC aims to accept or reject a new connection according to the negotiated parameters and the availability of resources in the network. This mechanism is not standardized and let to the operators. We tackle this point, by proposing in this study a new Admission Control (AC) that improves the QoS of BE traffic by avoiding a strict bandwidth assignment of other traffics (rtPS and nrtPS) as is defined in major previous studies. The proposed mechanism is based on token bucket for rtPS, nrtPS and BE traffics in order to reduce lightly the number of accepted connections and to improve considerably the number of accepted BE connections. To evaluate the performance of the proposed scheme, we use PEPS (Performance Evaluation of Parallel Systems) which is a powerful tool based on models which can be described with Stochastic Automata Networks (SAN). PEPS can solve complex models with a large state space and with many synchronized events. Therefore, we show that this tool is suitable for wireless network, and specifically for the proposed scheme, toward numerical results we show as we expected that our proposed AC outperform the classical one by reducing lightly the performance of other service classes.     

The design and development of suspended handles for reducing hand-arm vibration in petrol driven grass trimmer

The portable petrol driven grass trimmer is identified as a type of machine whose operator can be subjected to large magnitude of hand-arm vibration. These vibrations can cause complex vascular, neurological and musculoskeletal disorder, collectively named as hand-arm vibration syndrome. The vibration total level on the handle of grass trimmer of 11.30 m/s² was measured, and it has reached the exposure limit value of 5.0 m/s² for daily vibration exposure A(8). New suspended handles were designed to reduce the vibration level. Three different prototype handles with rubber mounts were designed. Handles were made of different materials, and the distance of rubber mounts were varied. From the study, it was observed that not all the handles with rubber mounts were effective in reducing hand-arm vibration. The reduction of vibration depended on the handle material and distance installed between rubber mount and vibration transmissibility of handle-isolation system. Subjective ratings of perception of vibration were measured, and the results indicated that operators were not fully aware of the level of vibration. A prototype handle that is made of heavier material results in the lowest hand-arm vibration of 2.69 m/s². The new handle has significantly reduced the vibration total value by 76% compare with the existing commercial handle.

Relevance to industry

Large numbers of workers are employed to perform grass trimming job in many developing countries. This paper presents the effect of handle types (commercial and prototype) on the commonly used grass trimmer.     

High-aspect ratio metal tips attached to atomic force microscopy cantilevers with controlled angle, length, and radius for electrostatic force microscopy

We demonstrate a method to fabricate a high-aspect ratio metal tip attached to microfabricated cantilevers with controlled angle, length, and radius, for use in electrostatic force microscopy. A metal wire, after gluing it into a guiding slot that is cut into the cantilever, is shaped into a long, thin tip using a focused ion beam. The high-aspect ratio results in considerable reduction of the capacitive force between tip body and sample when compared to a metal coated pyramidal tip.