Design of Polarization-independent Wavelength-interleave Coupler in Fluorinated Polyimide Waveguide

Based on the measurement of dispersion characteristic and birefractive index of the fluorinated polyimide film,a statistical optimum design method is proposed and used to realize the design of 32-and 36-wavelengths optical waveguide wavelength-interleave coupler (i,e.,interleaver) with the optimization of polarization fluctuation and wavelength interval of 0.8nm at 1550nm. The largest cross coupling ratios of the two interleavers are respectively less than 1.8% and 3.5%, while the least through coupling ratios are respectively greater than 98. 2% and 96. 5%. The output differences due to polarization fluctuation are less than 1.7% and 3.2%     

Preparation and Luminescence Spectra of Calcium- and Rare-Earth (R = Eu, Tb, and Pr)-Codoped α-SiAlON Ceramics

Rare-earth-doped oxynitride or nitride compounds have been reported to be luminescent and may then serve as new phosphors with good thermal and chemical stabilities. In this work, we report the photoluminescence (PL) spectra of europium-, terbium-, and praseodymium-doped Ca-α-SiAlON ceramics. The highly dense ceramics were prepared by hot pressing at 1750°C for 1 h under 20 MPa in a nitrogen atmosphere. Europium-doped Ca-α-SiAlON displayed a single broad emission band peaking at λ= 550–590 nm depending on the europium concentration. The emission bands in the spectra of europium-doped Ca-α-SiAlONs were assigned to the allowed transition of Eu²⁺ from the lowest crystal field component of 4 f ⁶5 d to ⁸S_7/2 (4 f ⁷) ground-state level. The emission spectra of terbium- and praseodymium-doped Ca-α-SiAlON ceramics both consisted of several sharp lines, which were attributed to the ⁵D₄→⁷F _j ( j = 3, 4, 5, 6) transitions of Tb³⁺ and ³P₀→³H _j ( j = 3, 4, 5) transitions of Pr³⁺, respectively. In particular, the terbium-doped α-SiAlON ceramics showed a strong green emission among these phosphors.     

Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

Synthesis of polymeric microspheres employing SPG emulsification technique

Relatively uniform polymeric microspheres, the coefficients of variation being close to 10%, were obtained by the BPO-initiated suspension polymerization of styrenic monomers. Unlike the conventional stirred-tank system, a particular microporous glass membrane (SPG) provided uniform monomer droplets continuously when monomer was allowed to permeate through the micropores. The monomer droplets were suspended in an aqueous solution containing the stabilizing agents, transferred to a stirred vessel, and polymerized. Up to 10μm spheres, of a far narrower size distribution than those obtained by conventional microsuspension polymerization spheres, were obtained. The initial droplet size and distribution were retained with the successful suppression of secondary particle nucleation by the addition of hydroquinone in the aueous phase. Crosslinked polystyrene spheres were also synthesized in the presence of various low-molecular-weight diluents. While a good solvent, toluene, was not so effective; poor solvents, n-heptane and n-heptane, easily yielded the microporous structure, the specific surface area being as high as 160 m²/g. © 1994 John Wiley & Sons, Inc.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Micromachining of electroformed nickel mold using thick photoresist microstructure for imprint technology

In order to fabricate polymer-based microstructures with feature sizes on the order of micrometers, we have been developing a microimprint technology with a fine nickel (Ni) mold instead of a conventional photolithography technique. The Ni mold was successfully fabricated by electroforming using a positive thick photoresist microstructure patterned on a silicon substrate as a replication master. The photoresist microstructure with excellent edge quality can be obtained under irradiation with single wavelength (g line) selected from a high-pressure mercury lamp. In addition, its sidewall angle in the range of 65° to 84° can be controlled precisely by varying the distance between a photomask and a photoresist surface. On the structured photoresist master, Ni was electroplated up to a thickness of about 110 μm, and then removed from the master. In this process, two-step electroplating at different current densities was carried out in order to prevent deformation of the photoresist master due to stress generated in a Ni electrodeposit. With the Ni mold, fine patterns with a width of 10 or 30 μm and a depth of 24 μm were almost completely transferred to polymetric materials (PMMA). The geometrical dimensions of the fabricated PMMA microstructures were found to be only about 10% reduction against the Ni mold.     

Real-time CAM-based Hough transform algorithm and its performance evaluation

Abstract. This paper proposes a highly parallel Hough transform algorithm for real-time straight-line extraction and its hardware implementation on a content-addressable memory (CAM). To achieve high-speed processing, incrementation for voting, which composes the Hough transform, and calculations for coordinate updating are carried out for the every scan line, not every edge pixel, and extracting maxima in Hough space is executed by parallel comparing. Moreover, variously weighted voting achieves more accurate line extraction in spite of the quantization error and noise in the image space. In the implementation, the CAM acts as a PE (processing-element) array that effectively performs highly parallel processing for the Hough transform and also as a memory for two-dimensional Hough space, and both voting and peak extraction are directly executed by the CAM. Evaluations of CAM hardware size, processing time and the accuracy of line extraction show that a real-time and high-resolution Hough transform for a 256256 picture can be achieved using a single CAM chip with current VLSI technology. This CAM-based Hough transform algorithm promises to be an important step towards the realization of a real-time and compact image-understanding system. Received: 15 August 1998 / Accepted: 15 March 2000