Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Lamellar thickening behaviour of nylon-6,6 crystal by annealing

Nylon-6,6 — a typical polyamide — was annealed in the swollen state in glycerol to promote the partial melting of the polymer crystal. The recrystallization or lamellar thickening of nylon-6,6 crystal following partial melting was easily induced by this annealing, and the lamellar thickness of the crystal increased stepwise by $\text{1}\text{2}$ monomer unit length with increasing annealing temperature or annealing time. In addition, another distinct layer-thickening mechanism was observed which led to approximately doubling (and frequently quadrupling) the straight stem length of the lamellar crystal for all samples annealed under adequate conditions. New melting endotherms corresponding to these layer thicknesses (range of long spacings 140–180Å) were obtained by differential scanning calorimetry (d.s.c.) at temperatures ranging from 270° to 282°C. The mechanism of lamellar thickening is discussed with reference to the experimental results.     

Gas pressure sintering of β-silicon nitride

The sintering behaviour of -Si₃N₄ powder was investigated in 980 kPa (10 atm) nitrogen at 1800–2000 °C. It is shown that -Si₃N₄ has a higher sinterability than the finer -Si₃N₄. The solution of small grains and reprecipitation on large grains occurred during sintering at >1600 °C. The rate-determining step in the liquid-phase sintering is believed to be the diffusion of material through the liquid phase at grain boundaries. There was no abnormal grain growth during gas pressure sintering of -Si₃N₄. The microstructures of gas pressure sintered materials from -Si₃N₄ were more uniform than those from -Si₃N₄. The densification mechanism of -Si₃N₄ is discussed in relation to that of -Si₃N₄.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Real-time CAM-based Hough transform algorithm and its performance evaluation

Abstract. This paper proposes a highly parallel Hough transform algorithm for real-time straight-line extraction and its hardware implementation on a content-addressable memory (CAM). To achieve high-speed processing, incrementation for voting, which composes the Hough transform, and calculations for coordinate updating are carried out for the every scan line, not every edge pixel, and extracting maxima in Hough space is executed by parallel comparing. Moreover, variously weighted voting achieves more accurate line extraction in spite of the quantization error and noise in the image space. In the implementation, the CAM acts as a PE (processing-element) array that effectively performs highly parallel processing for the Hough transform and also as a memory for two-dimensional Hough space, and both voting and peak extraction are directly executed by the CAM. Evaluations of CAM hardware size, processing time and the accuracy of line extraction show that a real-time and high-resolution Hough transform for a 256256 picture can be achieved using a single CAM chip with current VLSI technology. This CAM-based Hough transform algorithm promises to be an important step towards the realization of a real-time and compact image-understanding system. Received: 15 August 1998 / Accepted: 15 March 2000     

Pressure sintering of Si3N4

The sintering of Si₃N₄ with 5% MgO was investigated at 1450 to 1900 C under a pressure of nitrogen. A maximum density of 95% of the theoretical value was obtained, which is greater than that obtained by pressureless sintering. The sintering process was inferred to be liquid-phase sintering and divided into two processes; rearrangement and solution-precipitation. The contribution of rearrangement to densification was about 10% in the present system, and the rest, up to 17% was due to solution-precipitation. Application of the present method of sintering Si₃N₄ with a high strength grain-boundary phase at high temperature is surveyed.     

氧化物冶金技术的最新进展及其实践

文中介绍了氧化物冶金技术提出的背景,该技术的主要内容和采用该技术对钢的组织、性能的影响.总结了该技术近十几年来在利用夹杂物钉扎晶粒的高温长大和形核晶内铁素体(特别是其机理探讨)方面的相关研究,介绍了国外一些钢铁公司在大线能量焊接过程中所开发的该领域的新技术和新应用,同时介绍了氧化物冶金技术在焊接以外的凝固、压力加工、非调质钢和厚板生产等过程中的研究和应用的最新进展.文末展望了该技术的发展趋势.