Cholescintigraphy in the diagnosis of Rotor syndrome

A 2-year-old boy with Rotor syndrome was studied with Tc-99m N-(di-isopropylphenyl carbamoylmethyl) iminodiacetic acid (DIPA). In this patient, the liver was not visualized, and there was persistent visualization of the cardiac blood pool and along with prominent kidney excretion. It is concluded that Tc-99m DIPA cholescintigraphy may be helpful in the diagnosis of Rotor syndrome.     

Further study on the one-pot synthesis of (E)-2-nonenal from castor oil

A one-step procedure is described for the synthesis of (E)-2-nonenal from commercial castor oil by ozonolysis in methanol, followed by reduction of the ozonide products with dimethyl sulfide and exposure of the resulting intermediate product to dilute sulfuric acid. The developed process allows the production of the aldehyde with a yield of 80% at a purity of 95%. The method has advantages over all those reported earlier, because of inexpensive raw material and reducing agent, recycling of the solvent and its unusual simplicity.     

Curing temperature and humidity effects on the strength of an aluminous cement

The effects of curing temperature (21 and 60°C), time (1,7,28 days) and relative humidity (25 to 87%) on the strength and phase compositions of specimens prepared from neat Fondu paste with water/aluminous cement ratio of 0.30 were investigated. The room temperature strengths of the materials aged at 60°C, containing C₃AH₆ and AH₃, were higher than pastes cured at 21°C, containing CAH₁₀. Conversion at 60°C of the specimens aged at room temperature resulted in strengths comparable to materials isothermally cured at 60°C. The effects of these curing conditions on the high temperature strength were also investigated.     

Structure and properties of 6061 + 26 mass% Si aluminum alloy produced via coupled rapid solidification and KOBO-extrusion of powder

Experiments on mechanical consolidation of rapidly solidified (RS) powder of 6061 + 26 mass% Si alloy were performed using the oscillating-die extrusion method. The RS powder was wrapped in thin-wall 6061-alloy cup 35 mm in diameter and vacuum-compressed by means of 100 ton press. Bars 8 mm in diameter were extruded with cross-section reduction of λ = 19 without any preheating of the charge. Tubes with a diameter/wall thickness of 14 mm/1 mm and cross-section reduction of λ = 33 were also manufactured with success. TEM/STEM observations revealed a very fine structure of as-extruded material and bimodal distribution of quasi-spherical silicon particles. Statistical analysis revealed a silicon fine fraction of 0.1–0.7 μm and a coarse fraction 2.1–2.5 μm in diameter. Examination by means of TEM did not reveal any significant changes in the morphology of the silicon particles, even when a high extrusion ratio and the material annealing after deformation were used. Hot compression tests on as-extruded rods (λ = 19) and preliminary annealed samples were performed at a constant true strain rate of 5 × 10^?3 s^?1 within the temperature range of 293–823 K. High strength of the material and relatively high ductility of samples deformed by compression up to ?_t ? 0.4 were observed. The maximum flow stress value for as-extruded material was reduced with deformation temperature from ～390 to ～3.5 MPa for 293 and 823 K, respectively. Annealing of the samples at 773 K/30 min was found to reduce the maximum flow stress by 30–40%. Tensile strengths of similar as-cast alloys and materials manufactured by means of other powder metallurgy methods were shown for the purpose of comparison.     

Unit cell parameters of monosulfide,pentlandite and taenite solid solutions within the FeNiS system

The unit cell parameters of monosulfide, pentlandite and taenite solid solutions in the FeNiS system have been obtained from standardised Jagodzinski X-ray powder patterns of the products of quench-type, annealing experiments and compared with the chemical compositions of the coexisting phases determined by electron microprobe. In Fe-rich monosulfide solid solution, metal excess relative to (Fe,Ni)S causes a decrease in the a parameter whereas metal deficiency causes an increase in a. The structural accommodations made in quenched Ni-rich monosulfide solid solution for ordering associated with metal excess, metal deficiency and Fe/Ni variation are more complex. The Ni,Fe alloy taenite appears to take a small amount of S in solid solution which is reflected in a significant shift in the cell parameter.     

Continuous computer controlled production of formate dehydrogenase (FDH) and isolation on a pilot scale

A continuous production process has been developed up to pilot scale (300 l) for FDH production with the methylotrophic yeast Candida boidinii. A high cell mass specific FDH activity (50 U/g) is achieved by process computer controlled supply of pure methanol to operate the reactor at an optimum methanol concentration of 10 g/l. The maximum FDH spacetime yield achievable with this process control involves a residence time of 7 h. The FDH space-time yield (STY) and FDH concentration are a function of the oxygen transfer rate (OTR) of the fermenter (maximum STY = 255 U/(l h) at k_La = 870 l/h). For a reasonable compromise between high FDH space-time yield and high FDH concentration, an optimum residence time is adjustable by regulating the supply of nutrient salt solution in relation to the OTR of the fermenter. On a pilot scale (200 l continuously stirred tank reactor) roughly 4 million U of FDH were produced within 10 days at a residence time of 14.3 h. Isolation of intracellular FDH enzyme was performed using extraction with an aqueous two-phase system (PEG/K₂HPO₄). A technical product quality of 1.2 U/mg FDH was achieved without any chromatographic purification step.