Effect of site-selective substitution in bulk superconducting Tl2Ba2CaCu2O8

Magnetization measurements were carried out on bulk Tl₂Ba₂CaCu₂O₈ (referred to as Tl-2212) and on various site-selective substituted Tl-2212 samples. At 5K between 0 and 4.5 T, the 5 at. % Mg-doped Tl-2212 (Tl,Mg-2212) samples displayed enhanced pinning as demonstrated by a field dependent increase of the magnetic critical-current density J_c by 18 to 25 percent over that of pristine Tl-2212. Excess Mg (10–15 at. %), however, is deleterious. Rietveld refinement of the x-ray diffraction pattern showed Mg on the Tl sites. Auger electron spectroscopy analysis showed part of the Mg on grain boundaries. The flux-creep activation energies are higher for flux expulsion than for flux penetration in both Tl-2212 and Tl,Mg-2212 samples; the latter displays higher individual values. Our results demonstrate an increase in the number density of flux lines as a result of increased density of atomic-size-structural, defects by Mg (5 at. %) doping. In the Tl_2−yBa₂(Ca_1−zY_z)Cu₂O_8−x(z=0–0.3; single phase; x and y represent oxygen and thallium vacancies) system also studied, the T_c decreases as z increases. At z=0.3, the sample becomes an antiferromagnetic semiconductor.     

Processing Dependence of Texture, and Critical Properties of YBa2Cu3O7−δ Films on RABiTS Substrates by a Non-Fluorine MOD Method

YBa₂Cu₃O_{7− δ} (YBCO or Y123) films on rolling-assisted biaxially textured substrates (RABiTS) were prepared via a fluorine-free metallorganic deposition (MOD) through spin coating, burnout, and high temperature anneal. The effects of substrate texture and surface energy of the CeO₂ cap layer were investigated. Except for the commonly accepted key factors, such as the textures of substrate and buffer layers, we found some other factors, for example, the deposition temperature of the cap layer, are also critical to the epitaxial growth of Y123 phase. With the CeO₂ cap layer deposited at relative high temperature of 700°C, a critical current density, J _c, over 1 MA/cm² has been demonstrated for the first time on Ni-RABiTS by a fluorine-free MOD method. Whereas for samples with CeO₂ cap layers deposited at a lower temperature of 600°C, even though XRD data showed a better texture on these buffer layers, texture degradations of YBCO grains under the optimized processing conditions were observed and a lower oxygen partial pressure around 40 ppm was necessary for the epitaxial growth of Y123 phase. As a result, J _c fell to 0.45 MA/cm² at 77 K. The observed phenomena points to the change of surface energy and reactivity of the CeO₂ cap layer with respect to the CeO₂ deposition temperature. In this paper, the YBCO phase diagram was also summarized.     

Growth of Highly Oriented TlBa2Ca2Cu3O9—y Superconducting Films on Ag Substrates Using a Dip-Coated Barium Calcium Copper Oxide Sol—Gel Precursor

Thin films of Ba_zCa₂Cu₃O₇ a precursor of TIBa₂, Ca₂-Cu₃O_9-y, were prepared by sol-gel synthesis from an all alkoxide solution. The barium and calcium precursors were the respective metals reacted with 2-methoxyethanol, and the copper precursor was copper methoxide complexed by triethanolamine. Silver substrates were coated using the sol-gel solution by dip-coating. Subsequent processing included a low-temperature drying step (600°C), repeated coating to provide the desired thickness, heat treatment at 850°C in oxygen to remove carbon, and reaction at 860°C in a two-zone thallination furnace to produce a TIBa₂Ca₂-Cu₃O_9-y, superconducting film. These films were strongly c-axis-aligned, had a zero-resistance temperature (T₂) of 110 K, and a critical-current density (J_c) of 1.9 × 10₄ A/cmZ at 77 K and zero magnetic field.     

Melting and Vaporization of the 1223 Phase in the System (Tl-Pb-Ba-Sr-Ca-Cu-O)

The melting and vaporization of the 1223 [(Tl,Pb):(Ba,Sr):Ca:Cu] oxide phase in the system (Tl-Pb-Ba-Sr-Ca-Cu-O) have been investigated using a combination of dynamic methods (differential thermal analysis, thermogravimetry, effusion) and post-quenching characterization techniques (powder x-ray diffraction, scanning electron microscopy, energy dispersive x-ray spectrometry). Vaporization rates, thermal events, and melt compositions were followed as a function of thallia loss from a 1223 stoichiometry. Melting and vaporization equilibria of the 1223 phase are complex, with as many as seven phases participating simultaneously. At a total pressure of 0.1 MPa the 1223 phase was found to melt completely at (980 ± 5) °C in oxygen, at a thallia partial pressure (p_Tl2O) of (4.6 ± 0.5) kPa, where the quoted uncertainties are standard uncertainties, i.e., 1 estimated standard deviation. The melting reaction involves five other solids and a liquid, nominally as follows: 1223→1212+(Ca,Sr)2CuO3+(Sr,Ca)CuO2+BaPbO3+(Ca,Sr)O+LiquidStoichiometries of the participating phases have been determined from microchemical analysis, and substantial elemental substitution on the 1212 and 1223 crystallographic sites is indicated. The 1223 phase occurs in equilibrium with liquids from its melting point down to at least 935 °C. The composition of the lowest melting liquid detected for the bulk compositions of this study has been measured using microchemical analysis. Applications to the processing of superconducting wires and tapes are discussed.     

Mesoporous electroactive silver doped calcium borosilicates: Structural,antibacterial and myogenic potential relationship of improved bio-ceramics

In this work improved electroactive mesoporous Ag-doped bio-ceramics for medical usages are developed, examining their structural, electrical, in-vitro bioactivity, cell cultures and antibacterial properties against various classical pathogenic bacteria. Ag-containing mesoporous bio-ceramics (MBCs): xmol%Ag₂O - (100-x)[45.8CaO-8.4B₂O₃-45.8SiO₂] where x = 2, 5, 7.5 and 10 were synthesized through a sol-gel method. The small angle X-ray scattering and electron microscopy studies reveal the embedment of silver nanoparticles in the samples. Existence of silver as Ag⁺/Ag⁰ forms in the samples is confirmed by X-ray photoelectron spectroscopy. The N₂ adsorption-desorption analysis evidence the mesoporous structure of the samples. The electrical conductivity of samples increases from 5.4 x 10^?8 S cm^?1 for x = 2 to 1.9 x 10^?6 S cm^?1 for x = 7.5 and then decreases to 0.9 x 10^?6 S cm^?1 for x = 10 at 110 °C. In vitro bioactivity studies revealed that Ag-containing MBCs hold the bone-like hydroxyapatite formation after immersion in human blood plasma like-solution such as Dulbecco's Modi?ed Eagle's Medium. The antibacterial effect of samples against pathogenic bacteria (S. aureus, E. coli, P. monas aeruginosa, and B. cereus) increases with Ag concentration (x = 7.5) and then decreases with Ag content (x = 10). Antibacterial effect is greater for the sample with high electrical conductivity. The cell culture studies evidence not considerable cytotoxic effects for Ag-containing MBCs. Finally, the C2C12 myoblast cell culture studies reveal the significant cell growths and differentiation (myogenesis) for high electrical conducting Ag-containing MBCs.     

MADE3D: Enabling the next generation of high-torque density wind generators by additive design and 3D printing

Forschung im Ingenieurwesen - Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments—especially offshore, where reliability and efficiency...     

Influence of Substrate Temperature on the Properties of Cobalt Oxide Thin Films Prepared by Nebulizer Spray Pyrolysis (NSP) Technique

Cobalt oxide thin films are prepared by the nebulizer spray pyrolysis technique using cobalt chloride as the precursor material. The structural, optical, morphological and electrical properties are investigated as a function of substrate temperature (300–450 °C). The X-ray diffraction (XRD) analysis reveals that all the films are polycrystalline in nature, having cubic structure with preferential orientation along the (111) plane. The optical spectra show that the films are transparent (68 %) in the IR region. The optical band gap values are calculated for different substrate temperature. Photoluminescence (PL) spectra of the films indicate the presence of indigo, blue and green emission peaks with an ultraviolet emission peak centered around 368nm. SEM images reveals small sphere-like structures for the prepared Co3O4 films. The maximum conductivity obtained is 1.48 x 10?3 S/cm at 350 °C. The activation energy varies between 0.039 and 0.138 eV for the substrate temperature variation from 300-450 Q°C.     

Preparation of YBCO Films on CeO2-Buffered (001) YSZ Substrates by a Non-Fluorine MOD Method

YBa₂Cu₃O_7−δ (YBCO) films were fabricated via a fluorine-free metal organic deposition (MOD) method followed by high-temperature, low oxygen partial pressure annealing. Trimethyl acetate salts of copper, yttrium, and barium hydroxide were used as the precursors, which were dissolved in proponic acid- and amine-based solvents. After spin-coating and burnout, samples were annealed at 740°C in 180 ppm oxygen partial pressure and exposed to humid atmosphere for different times. A critical transition temperature, T _c( R =0) of 90.2 K and a transport critical current density ( J _c) of 0.55 MA/cm² (77 K and self-field) were obtained for 0.2 μm YBCO films on CeO₂-buffered yttria-stabilized zirconia (YSZ) substrates. X-ray studies shows that the YBCO films have sharp in-plane and out-of-plane texture for all samples; however, the porosity of the YBCO film varies with the time of exposure to the humid atmosphere. A reaction between YBCO and CeO₂ during the high-temperature anneals and formation of the reaction product BaCeO₃ was confirmed by X-ray diffraction (XRD) studies. The XRD and transmission electron microscopy analysis indicated that the epitaxial relations in the film were YBCO (00 l )//CeO₂ (00 l )//YSZ (00 l ) and YBCO [100]//CeO₂ [110]//YSZ [110].