STI process steps for sub-quarter micron CMOS

This paper presents Shallow Trench Isolation (STI) process steps for sub-1/4 μ CMOS technologies. Dummy active areas, vertical trench sidewalls, excellent gap filling, counter mask etch step and CMP end point detection, have been used for a 0.18 μm CMOS technology. Electrical results obtained with a 5.5 nm gate oxide thickness show good isolation down to 0.3 μm spacing. Good transistor performances have been demonstrated.     

Influence of numerical and viscous dissipation on shock wave reflections in supersonic steady flows

Numerical simulations are investigated to describe precisely the shock wave reflections in supersonic steady air flow field. The main objectives are to study the influence of the wedge trailing edge corner angle, of the numerical methods and of the viscous effects on the shock wave reflections and on the hysteresis behavior. The computations are done with different MUSCL-TVD finite volume schemes and the corresponding results are compared. The flow viscosity is also taken into account and comparisons are made between inviscid and viscous flow simulations. The results display the non-negligible influence of the numerical scheme accuracy on the results, mainly on the position and height of the Mach stem, and the relatively weak influence of the flow viscosity on these parameters. Comparisons between numerical results and experimental data have also been done and a good agreement is only observed for small wedge angles mainly due to the three-dimensional effects in the experimental setup.     

Frequency and etiology of calf losses and calf diseases before weaning in cow-calf farms. II. Microbiological and parasitological diagnoses in diarrheic calves]

Diarrhea is the most frequently diagnosed disease in Swiss cow-calf farms. During an longitudinal study conducted in 105 cow-calf farms in Switzerland in 1993-95, blood and fecal samples were collected from diarrheic calves and from calves that died because of diarrhea. Campylobacter spp. were detected in 42%, E. coli (VTEC) in 32%, rotavirus in 33%, coronavirus in 13%, coccidia in 43% and helminths in 8% of the cases. In some samples Yersinia pseudotuberculosis were isolated. The BVD-virus antigen was not detected in any of the calves examined. In most cases concurrent infection with several enteropathogens was diagnosed. Specific causes of diarrhea were therefore difficult to establish. The bacteriological findings of this study have implication for food safety: VTEC, Campylobacter spp. Yersinia spp. and cryptosporidia are considered as potential causes on zoonoses.     

An investigation of carbon nanotube jet grinding

Since their observation in 1976 and 1991, carbon nanotubes (CNTs) have generated much interest due to their properties and potential applications. CNTs are tubular carbon molecules with remarkable mechanical, electrical, chemical and thermal properties, which make them useful in various applications. Industries producing CNTs via the fluidized bed chemical vapor deposition technique face challenges related to the size of CNT bundles. The two main challenges are agglomeration and agglomerate size distribution control. A solution to these challenges involves the use of jet mills to grind the CNT agglomerates. The goal of this study was to determine whether the nanotubes could be ground with air jets using a commercial jet mill and apply a two-parameter model to describe the grinding process. The present study has indicated that air-jet grinding of CNTs is feasible with a typical commercial jet mill. This paper presents the effect of operational parameters on the arithmetic mean diameter of the ground product. Sonic velocity through the grinding nozzles was required to obtain reasonable grinding rates and relatively narrow particle size distributions. This occurs at high air to solids feedrate ratios. Additionally, a simple attrition model can describe the grinding process in the spiral jet mill.     

Coverage-biased random exploration of large models and application to testing

This paper presents several randomised algorithms for generating paths in large models according to a given coverage criterion. Using methods for counting combinatorial structures, these algorithms can efficiently explore very large models, based on a graphical representation by an automaton or by a product of several automata. This new approach can be applied to random exploration in order to optimise path coverage and can be generalised to take into account other coverage criteria, via the definition of a notion of randomised coverage satisfaction. Our main contributions are a method for drawing paths uniformly at random in composed models, i.e. models that are given as products of automata, first without and then with synchronisation; a new efficient approach to draw paths at random taking into account some other coverage criterion. Experimental results show promising agreement with theoretical predictions and significant improvement over previous randomised approaches. This work opens new perspectives for future studies of statistical testing and model checking, mainly to fight the combinatorial explosion problem.     

On the role of conserved proline residues in the structure and function of Clostridium pasteurianum 2[4Fe-4S] ferredoxin

The widespread occurrence of Pro residues adjacent to Cys ligandsin the sequences of [4Fe-4S] electron transfer proteins hasnot yet found a functional basis. The two such Pro of Clostridiumpasteurianum 2[4Fe-4S] ferredoxin have been probed by site-directedmutagenesis. Any one of them, but not both simultaneously, canbe substituted without impairing the proper folding of the protein.The reduction potentials of the ferredoxin variants fall ina narrow range of <20 mV above the potential of the nativeprotein. The biological activities with C.pasteurianum hydrogenaseand pyruvate-ferredoxin oxidoreductase do not change significantly,except when Lys replaces Pro. In these cases, the data suggestthat the two clusters of 2[4Fe-4S] ferredoxin may not alwaysbe equivalent in the interaction with the redox partners. Destabilizationof the structure has been observed as the consequence of theProl9 or Pro48 substitutions. Using 2-D NMR, this effect hasbeen associated with perturbations of both the hydrogen bondnetwork and one amino acid side chain around the [4Fe-4S] clusters.Thus, the conserved Pro found in the binding motif of [4Fe-4S]clusters in proteins strongly stabilizes the active site butdoes not play an essential role in the mechanism of electrontransfer.     

Zinc Coated Steel/Epoxy Adhesive Systems: Investigation of the Interfacial Zone by FTIR Spectroscopy

The present study takes advantage of the ability of Fourier Transform Infrared Spectroscopy (FTIR) for the analysis of ultrathin organic films on metals. FTIR in the reflection mode (IRRAS) is used in order to study the interaction of ultrathin films of dicyandiamide (hardener of most one-pack epoxy resins) with various substrates, model ones such as gold or zinc and industrial ones such as steel and zinc-coated steels.

Pure zinc surfaces and, to a lesser extent, zinc-coated steels are shown to react with dicyandiamide after heating at 180°C, as evidenced by the frequency shift of the absorption band (at about 2200 cm^-1) characteristic for nitrile groups. As real systems consist of thick layers of a fully formulated adhesive cured onto a metallic substrate, the direct investigation of such a buried interphase is no longer possible by FTIR and by most of the known spectroscopies. Some mechanically tested specimens are then analysed, after failure, by FTIR microspectrometry. The spectra obtained, corresponding to the fracture initiation zone which is about 100 μm in diameter, advocate for the presence of an ultrathin layer of modified polymer still covering the substrate.     

Factors influencing encapsulation behavior in composite droplet-type polymer blends

In this study the influence of the molecular weight of the dispersed phase components on encapsulation effects in the composite droplet phase was examined for high density polyethylene (HDPE)/PS/PMMA ternary blends. Three different blends composed of various PS and PMMA materials dispersed in an HDPE matrix were prepared using an internal mixer. The morphology was studied by light and electron microscopy. Current models used for predicting encapsulation effects and composite droplet formation in ternary systems (based on static interfacial tension) predict in all cases that PS will encapsulate the PMMA. However, in one case, an unexpected encapsulation of PS by PMMA was observed. It was found that arguments based on the effect of viscosity ratio or the absolute viscosity of the different dispersed phases do not explain that discrepancy. In addition, the reversal of that latter composite droplet morphology from PMMA encapsulating PS to PS encapsulating PMMA was observed upon annealing treatment. Considering all the above, a conceptual model was developed to predict encapsulation effects in composite droplet type systems based on the use of a dynamic interfacial tension (i.e. taking into account the elasticity of the polymer components). Calculations based on the dynamic interfacial tension model, using elasticities based on constant shear stress, were able to account for all of the observed encapsulation effects in this study.     

Cell structure and dynamic properties of injection molded polypropylene foams

The cell structure and properties of branched and linear polypropylene (PP) foams containing organically modified nanoclay and maleic anhydride grafted polypropylene (PPMA) have been thoroughly investigated. X-ray diffraction (XRD) and melt rheometry were used to identify the structure and linear viscoelastic properties of the nanocomposites, as well as the effectiveness of two different compatibilizers. These nanocomposites were used in injection molding to investigate their foamability and the influence of experimental conditions such as chemical foaming agent concentration, shot size, back pressure, injection speed, as well as melt temperature and different injection methods on the resulting cell structure of the foams. Quite different results were obtained with the linear and the branched PP. While the foamability of the branched PP was intrinsically good, that of the linear one could largely be improved by modifying its rheological properties and favoring nucleation through the addition of nanoclay. The effect of cell structure on the dynamic mechanical properties of the foams was also investigated using dynamic mechanical analysis (DMA). POLYM. ENG. SCI., 47:1070–1081, 2007. © 2007 Society of Plastics Engineers     

Using electric actuation and detection of oscillations in microcantilevers for pressure measurements

Response characteristics of a microcantilever, such as resonant frequency, amplitude, phase and quality factor, can be used for absolute pressure measurements in the range of 10⁻⁴ to 10³ Torr. To this end, it would be very convenient to have the resonance of the microcantilever actuated and detected electrostatically. Herein, we report the nonlinear dynamics of microcantilevers under varying pressure and different gases using the harmonic detection of resonance (HDR) technique [J. Gaillard, M.J. Skove, R. Ciocan, A.M. Rao, Electrical detection of oscillations in 340 microcantilevers and nanocantilevers, Rev. Sci. Instrum. 77 (2006) 073907]. The HDR technique exploits nonlinearities in the cantilever-counter electrode system to allow electrostatic actuation and detection of the responses of the microcantilever to the pressure and gas composition. In particular, the 2nd and 3rd harmonics of the measured charge on the cantilever are investigated. The microcantilever demonstrates a quality factor of 10,000 at 10⁻³ Torr, and a usable response in the range from 10⁻³ to 10³ Torr. The use of different harmonics can enable us to adjust the range of pressures over which the sensor has an efficacious response, enhancing its sensitivity to a particular environment. The experimental results are in reasonable agreement with theoretical calculations, despite the nonlinearities involved.